Erbauer ERB383WCH User manual
1500W WALL CHASER
ERB383WCH
Original Instructions
(Version 2.0)
1500W WALL CHASER
GUARANTEE
This product carries a 2 year guarantee. If your product develops a fault within this
- Fair wear and tear
- Misuse or abuse
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
For further technical advice, spare parts or repair service (outside of guarantee) please con-
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This
product should give you reliable service but for your peace of mind this
power tool does carry a 2 year guarantee, the terms of which are detailed below.
If this product develops a fault within the guarantee period contact your retailer.
Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions.
Save all warnings and instructions for future reference.
(corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
cords increase the risk of electric shock.
e
)
When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f
)
If operating a power tool in a damp location is unavoidable,
1500W WALL CHASER
use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
or medication.
b) Use personal protective equipment. Always wear eye
protection.
safety shoes, hard hat, or hearing protection used for appropriate
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on.
A wrench or a key left attached to a rotating part of the power tool
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool in
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving parts.
parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct power tool for
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making any
adjustments, changing accessories, or storing power tools.
power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are
f) Keep cutting tools sharp and clean.
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
result in a hazardous situation.
5. Service
person using only identical replacement parts. This will
b) If the replacement of the supply cord is necessary, this
has to be done by the manufacturer or his agent in order to
avoid a safety hazard.
1500W WALL CHASER
ADDITIONAL SAFETY RULES FOR YOUR WALL CHASER
a) The guard provided with the tool must be securely attached
to the power tool and positioned for maximum safety, so
the least amount of wheel is exposed towards the operator.
Position yourself and bystanders away from the plane of the
rotating wheel.
b) Use only bonded reinforced or diamond cut-off wheels for
your power tool. Just because an accessory can be attached to
your power tool, it does not assure safe operation.
c) The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
d) Wheels must be used only for recommended applications.
For example: do not grind with the side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral grinding, side
diameter for your selected wheel
the wheel thus reducing the possibility of wheel breakage.
f) Do not use worn down reinforced wheels from larger power
tools. Wheels intended for a larger power tool are not suitable for
g) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
spindle of the power tool.
i) Do not use damaged wheels. Before each use, inspect
the wheels for chips and cracks. If power tool or wheel is
dropped, inspect for damage or install an undamaged wheel.
After inspecting and installing the wheel, position yourself
and bystanders away from the plane of the rotating wheel and
run the power tool at maximum no load speed for one minute.
j) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and shop apron capable of stopping small abrasive or
workpiece fragments.
cause hearing loss.
k) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
equipment.
l) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting accessory
m) Position the cord clear of the spinning accessory. If you
n) Never lay the power tool down until the accessory has come
to a complete stop.
and pull the power tool out of your control.
o) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
p) Regularly clean the power tool’s air vents.
r) Do not use accessories that require liquid coolants. Using
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged rotating
wheel. Pinching or snagging causes rapid stalling of the rotating
1500W WALL CHASER
wheel which in turn causes the uncontrolled power tool to be forced
binding.
workpiece, the edge of the wheel that is entering into the pinch point
conditions.
procedures or conditions and can be avoided by taking proper
precautions as given below.
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper precautions
are taken.
b) Never place your hand near the rotating accessory. Accessory
c) Do not position your body in line with the rotating wheel.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain, woodcarving blade, segmented
diamond wheel with a peripheral gap greater than 10 mm or
toothed saw blade. Such blades create frequent kickback and
loss of control.
f) Do not “jam” the wheel or apply excessive pressure. Do not
attempt to make an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility
to twisting or binding
of the wheel in the cut and the possibility of kickback or wheel
breakage.
g) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the wheel from the cut while the wheel is
in motion otherwise kickback may occur. Investigate and take
h) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut. The
in the workpiece.
i) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend to
workpiece near the line of cut and near the edge of the workpiece
on both sides of the wheel.
j) Use extra caution when making a “pocket cut” into existing
walls or other blind areas.
ADDITIONAL SAFETY RULES:
1. Always wear a dust mask.
2. Always wear safety glasses or eye shields when using the
WALL CHASER Everyday eyeglasses have only impact-
resistant lenses; they are NOT safety glasses. Following this
3. Always wear hearing protection during extended periods
of operation. Following this rule will reduce the risk of serious
4. Keep your hands away from cutting area. Do not reach under
5. Do not use dull or damaged blades. Bent blades can break
easily, or cause kickback.
6. Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
7. Fully unwind cable drum extensions to avoid potential
overheating.
8. When an extension cable is required you must ensure it has
1500W WALL CHASER
the correct ampere rating for your power tool and is in a safe
electrical condition.
9. Ensure your mains supply voltage is the same as indicated
on the rating plate.
10.Your tool is double insulated for additional protection against
a possible electrical insulation failure within the tool.
power cables and pipes.
12.After long working period, external metal parts and
accessories could be hot.
13.Only withdraw the blade from the cut when the blade has
been stopped moving.
material being cut to reduce saw vibration, blade jumping
and blade breakage.
15.Before cutting, check the cutting line is free of nails, screws,
etc.
prevent movement.
17.Never stop the cutting blade by applying side pressure to the
blade.
Warning: Some dust particles created by power sawing, contain chemicals
known to cause cancer, birth defects or other reproductive harm.
•
•
•
• Work in a well-ventilated area.
•
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help reduce
daily basis and the choice of tool.
Further Advice can be found at www.hse.gov.uk
Typical weighted vibration
h2
used with the current guidance on vibration.
Warning:
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct
working practices in order to reduce the exposure to vibration.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
Warning:
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate)
If the tool is to be used regularly then invest in anti vibration accessories.
0C or less
1500W WALL CHASER
Health Surveillance
any vibration related diseases at an early stage, prevent disease progression and help
Double insulation
earthed.
Important note
with a two-core cable and plug.
SYMBOLS
Double insulation
Warning
Wear ear protection
Wear eye protection
Waste electrical products should not be disposed of with household waste.
or retailer for recycling advice.
1500W WALL CHASER
12
4
35
7
9
16 17 18 1915141312 6
1011
8
1. ON/ OFF TRIGGER SWITCH
2. SAFETY BUTTON OF SWITCH
3. ATTACHMENT POINT FOR AUXILIARY HANDLE
4. FIXED GUARD
5. CONNECTION TO DUST EXTRACTION
6. GUIDE WHEEL
7. FLANGE CAP LOCK KNOB
8. FLANGE CAP
9. BASE PLATE
10. OUTER FLANGE
11. DISTANCE WASHERS
12. CAP OF CARBON BRUSH (ON BOTH SIDES)
13. SPINDLE LOCKING BUTTON
14. DIAMOND CUTTING DISC
15. CUTTING DIRECTION
16. AUXILIARY HANDLE
17. CHISEL
18. SPANNER
19. HEX KEY
1500W WALL CHASER
TECHNICAL DATA
Rated voltage
Rated power
Rated speed
Blade size
Cutting depth
Cutting width
Protection class
Weight
NOISE INFORMATION
A weighted sound pressure LpA
A weighted sound power LwA
KpA & KwA
ACCESSORIES
125mm Diamond disc 2pcs
Spanner for screw loosen/tighten 1pc
Hex key for blade change 1pc
Chisel for material removal 1pc
Auxiliary handle 1pc
OPERATION
NOTE: Before using the tool, read the
instruction book carefully.
1. FITTING CUTTING DISCS (See Fig. 1-11)
Warning: Please make sure the blade is
diamond cutting disc which can cut
concrete, masonry and paving.
Always turn off and unplug the tool before
cap (See Fig.1).
the spindle lock button (See Fig. 2), then take out
the distance washers (See Fig.
cutting disc and distance washers onto the spindle.
Place the other cutting disc on the washer. (See Fig.
press in the spindle lock button (See Fig.
See
Fig.
Flange
cap
lock
knob
Outer flange
Fig. 1
Fig. 2
Fig. 3
Fig. 4
1500W WALL CHASER
Fig. 5
Fig. 8
Fig. 7
Fig. 6
Fig. 8
Fig. 9
Fig. 12
Fig. 11
Fig. 10
2. ADJUSTING CHANNEL WIDTH
width. The thickness of these washers is about
the spanner (See Fig. 2), take out the distance
width (See Fig.
clockwise fully.
3. ADJUSTING CHANNEL DEPTH
See Fig. 10) and
(See Fig. 11).
Set the cutting depth as the scale provided and
tighten the knob clockwise to lock.
4. INSTALLING THE AUXILIARY HANDLE (See
Fig. 12)
until it is secured fully.
Note:
Other manuals for ERB383WCH
1
Table of contents
Other Erbauer Power Tools manuals
Erbauer
Erbauer ERB140D User manual
Erbauer
Erbauer ERB900 User manual
Erbauer
Erbauer ERB474HT User manual
Erbauer
Erbauer ERB383WCH User manual
Erbauer
Erbauer ERB125Y User manual
Erbauer
Erbauer ERB807A User manual
Erbauer
Erbauer ERB706SA User manual
Erbauer
Erbauer ERI065JSW User manual
Erbauer
Erbauer ER2100 User manual
Erbauer
Erbauer ERN634ATL User manual
Erbauer
Erbauer ERN647ATL-I User manual
Erbauer
Erbauer EJS18-Li User manual
Erbauer
Erbauer ERB096HTG User manual
Erbauer
Erbauer ERB389JSW User manual
Erbauer
Erbauer EHTIW18-Li User manual
Erbauer
Erbauer EID18-Li User manual
Erbauer
Erbauer ERB108SDR User manual
Erbauer
Erbauer EWC1500 User manual
Erbauer
Erbauer ERI068TOR Operator's manual
Erbauer
Erbauer ERB567DRH User manual
