Taylor T-2XS User manual

T-2XS Aircraf
T-3XS Rive ing
T-4XS Hammers
USE 90 PSI MAXIMUM
Ref # Part # Qty.
234XS01
2X02
3X02
4X02
2X03
34X03
234X04
234X05
234X06
234X07
234X08
234X19
234X20
De cription
hrottle Button
2X Cylinder
3X Cylinder
4X Cylinder
2X Piston
3X,4X Piston
Bushing
Valve Box
Valve
Pin
Valve Seat
Stop Pin
Exhaust Cover
1
2
2
2
3
3
4
5
6
7
8
19
20
1
1
1
1
1
1
1
1
1
1
1
1
1
505 N. Railroad Ave. (33435)
P.O. Box 1117 (33425)
Boynton Beach, Florida
Ph. [phone]
Fax [phone]
oll Free 800-805-8665
Ref # Part # Qty.
-5210
-5120
234XS23
234XS24
234XS25
234XS26
234XS27
234XS28C
234XS29
234XS30
234XS31
234XS32
De cription
Beehive Spring
Quick Change Spring
Roll pin
hrottle Bushing
Hex Bolt
Spring Washer
Adjusting Bar
Handle Complete
O-Ring
Valve
Spring
Plug
22
21
23
24
25
26
27
28
29
30
31
32
1
0pt.
1
1
1
1
1
1
1
1
1
1
For use with .401 shank rivet sets and chisels
When not using this tool, keep it in a clean, dry place.
Grinding dust and metal chips may jam the piston or valves.
FOR WARRANTY INFORMATION &
WARRANTY REGISTRATION VISIT
www.taylorpneumatic.com
0523T TC /all rights reserved /CO YRIGHT 2023 / final
OILING INSTRUCTIONS:
OIL AFTER EACH USE
WITH A FEW DROPS OF
AIRTOOL OIL THROUGH
THE AIR INLET. RUN
FOR 1 SECOND TO COAT
ALL INTERNAL PARTS.

505 N Railroad Ave. (33435)
P.O. Box 1117 (33425)
Boynton Beach, Florida
SEE OUR CATALOG
at
www.taylorpneumatic.com
PH. 561-732-1111
FAX [phone]
OLL FREE 800-805-8665
11/15 P C /all rights reserved /COPYRIGH 2015 / final
General Air Hammer
Main enance T-7111,T-7151,
T-1X, T-1XS,T-2X, T-3X, T-4X,& XS,5X,7X,9X,
T-#2,#3,#4 & T-#24B, T-#34B & T-#44B
- OILING & SPECIFIC HAMMER INSTRUCTIONS:
*ALWAY USE CLEAN DRY CO PRESSED AIR @ OR BELOW 90
PSI.
*USING DIRTY AIR CAN CAUSE THE VALVES OR PISTON TO
JA AND VOIDS THE WARRANTY.
*IF AIR IS WET, THE INSIDE OF THE TOOL CAN RUST AND
VOIDS THE WARRANTY.
*USING ORE THAN 90 PSI CAN DA AGE THE VALVES AND
PISTON (THEY ARE ONLY DESIGNED TO TAKE SO UCH
PRESSURE), USING HIGH PRESSURE VOIDS THE
WARRANTY.
*NEVER DRY FIRE TOOLS. THEY NEED TO BE AGAINST THE
CHISEL AND WORK BEFORE THE TRIGGER IS DEPRESSED.
IF THE TOOL IS DRY FIRED DA AGE TO THE PISTON AND
BARREL AY OCCUR AND THIS WILL VOID THE WARRANTY.
* ALWAYS CHECK TO BE SURE THAT THE BARREL IS TIGHT
IN THE HANDLE. LOOSE HANDLES CAN DA AGE THE
HANDLE THREADS AND VOID THE WARRANTY. OIL AFTER
EACH USE WITH 1/2 TEASPOON OF AIRTOOL OIL THROUGH
THE AIR INLET. RUN FOR ONE SECOND TO COAT ALL
INTERNAL PARTS.
- GENERAL INSTRUCTIONS
1. ALWAYS DISCONNECT THE TOOL FRO AIR SOURCE
WHEN CHANGING ACCESSORIES OR SERVICING THE TOOL.
2. USE SAFETY GLASSES, FULL FACE SHIELDS, HEARING
PROTECTION AND GLOVES.
3. USE WHIP HOSE FOR QUICK DISCONNECTS.
4. VIBRATION AY BE HAR FUL TO YOUR AR S AND HANDS.
WEAR PROTECTION.
5. INSPECT THE TOOL AND AIR SUPPLY ON A REGULAR
BASIS.
6. DO NOT RE OVE GUARDS OR SAFETY DEVICES. DO NOT
ODIFY OR DEFEAT SAFETY DEVICES.
7. DO NOT AKE CONTACT WITH ELECTRICAL LINES.
8. LEAVE TRIGGER OFF BEFORE CONNECTING THE TOOL TO
THE AIR SUPPLY. AVOID ACCIDENTAL STARTS.
9. WEAR THE PROPER CLOTHING. DO NOT WEAR JEWELRY,
LOOSE CLOTHING, OR LONG HAIR AS IT CAN GET CAUGHT
IN ROTATING PARTS. KEEP GLOVES AWAY FRO OVING
PARTS.
10. DO NOT WORK IN HAZARDOUS AT OSPHERES WHERE
SPARKS COULD IGNITE OR DETONATE FU ES.
11. WATCH WHAT YOU ARE DOING. USE CO ON SENSE
WHEN OPERATING PNEU ATIC TOOLS. DO NOT USE
PNEU ATIC TOOLS WHEN TIRED OR UNDER THE
INFLUENCE OF EDICATION, ALCOHOL OR DRUGS. SERIOUS
PERSONAL INJURY AY RESULT FRO A O ENTS
INATTENTION.
12. USE 90 PSI AT THE TOOL. USE 3/8”, 1/2” or 3/4” HOSE OR
LARGER WITH FITTINGS 9/32 INI U I.D. AS SPECIFIED
13. ONLY USE CLEAN DRY CO PRESSED AIR. NEVER USE
OXYGEN, CARBON DIOXIDE, CO BUSTIBLE GASES OR ANY
OTHER BOTTLED GAS TO POWER THIS TOOL.
14. SECURE YOUR WORK BEFORE STARTING - USE CLA PS
OR FIND A SUITABLE WAY TO AINTAIN STABILITY.
15. STORE TOOLS IN A CLEAN DRY ENVIRON ENT.
16. DO NOT USE DA AGED TOOLS - ARK, AND RETURN
FOR SERVICE.
17. NEVER FORCE THE TOOL, LET THE TOOL DO THE WORK.
18. STOP USE I EDIATELY IF TOOL IS AKING AN UNUSUAL
NOISE OR VIBRATION. HAVE TOOL CHECKED BY
PROFESSIONAL TECHNICIAN.
19. WORK IN A WELL VENTILATED AREA AND USE APPROVED
PERSONAL PROTECTIVE EQUIP ENT SUCH AS DUST
ASKS, THAT ARE SPECIFICALLY DESIGNED TO FILTER OUT
ICROSCOPIC PARTICLES. SO E DUST CREATED BY
POWER SANDING, SAWING, GRINDING AND OTHER
CONSTRUCTION ACTIVITIES CONTAIN CHE ICALS KNOWN
TO CAUSE CANCER, BIRTH DEFECTS OR OTHER
REPRODUCTIVE HAR . SO E EXA PLES OF THESE
CHE ICALS ARE: CRYSTALLINE SILICA FRO BRICKS,
CE ENT AND OTHER ASONRY PRODUCTS, ARSENIC AND
CHRO IU FRO CHE ICALLY TREATED LU BER AND
LEAD FRO LEAD BASED PAINTS. YOUR RISK FRO
EXPOSURE VARIES, DEPENDING ON HOW OFTEN YOU DO
THIS TYPE OF WORK. TO REDUCE YOUR EXPOSURE TO
THESE CHE ICALS WEAR PROTECTIVE ASKS AND
CLOTHING.
20. KEEP CHILDREN, PETS AND BYSTANDERS AWAY WHILE
OPERATING A PNEU ATIC TOOL. DISTRACTIONS CAN
CAUSE YOU TO LOSE CONTROL. PROTECT OTHERS IN THE
WORK AREA FRO DEBRIS SUCH AS ETAL FILINGS AND
SPARKS. PROVIDE BARRIERS OR SHIELDS AS NEEDED.
21. THESE WARNINGS AND INSTRUCTIONS CAN NOT COVER
ALL POSSIBLE CONDITIONS OR SITUATIONS. THE
OPERATOR UST UNDERSTAND THAT CO ON SENSE AND
CAUTIONS ARE FACTORS WHICH CAN NOT BE BUILT INTO
THE PRODUCT BUT UST BE SUPPLIED BY THE OPERATOR.