ErGear EGDS2 User manual

Desk Monitor Arm
Instuction Manual
Technical Support:
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info: [email protected]
Website: https://ergear.com
EGDS2
Rev00(A)

4.4-26.4 lbs
(2.0-12 kg)
If your monitor weighs
more or less than the
range above, this mount
is NOT compatible.
Monitor should not
exceed maximum listed
weight.
WARNING
DO NOT exceed the maximum weight indicated. This
mounting system is intended for use only within the
weight range listed. Exceeding the maximum weight limit
may result in failure of the mount, causing potential
damage and / or injury.
It is the responsibility of the installer to verify the total
weight of the monitor and any accessories attached.
• Please carefully read all instructions before attempting installation. If you do not understand the
instructions or have any questions or concerns, please contact our Technical Support at
1-800-651-9525 (US / CA), 44-808-196-3875 (UK) or Customer Service at [email protected].
CAUTION: Avoid potential injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do not
exceed weight capacity. We are not liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
• This product contains gas spring arms which are under high pressure. Do Not puncture these
arms or expose the arms to fire or flame. If product is defective, please contact our Technical
Support at 1-800-651-9525 (US / CA), 44-808-196-3875 (UK) or Customer Service at
[email protected].
• Do Not use this product on desks made of particle board or other soft woods.
• The information contained in this manual does not cover all possible conditions or variables in
relation to the install of this product.
If your Monitor's VESA Pattern is smaller than 75mm x 75mm / 3” x 3” or greater than
100mm x 100mm / 3.9” x 3.9”, this mount is NOT COMPATIBLE. Please contact our Technical
Support at 1-800-651-9525 (US / CA), 44-808-196-3875 (UK) or Customer Service at
[email protected].
W
H
Minimum: 75mm x 75mm / 3” x 3” (W x H)
Maximum: 100mm x 100mm / 3.9” x 3.9” (W x H)
Measure Your Monitor's VESA Pattern:
Important Safety Information
Weight Restrictions
Check the VESA Pattern of Your Monitor before Installation
01

Grommet Mounting for grommet bolt
0.4 - 3.5” (10 - 90mm)
C-Clamp Mounting for table edge
0.4 - 3.5” (10 - 90mm)
360° 360° 180°
360°
21''
(533mm)
+85°/ -30°
Product Features
02

DO NOT adjust tension without monitor attached.
1. Verify the weight of your monitor (including accessories) is between
4.4 - 26.4 lbs (2 - 12 kg).
2. Monitor weight information can be found within its box or manual.
3. Ensure monitor has been securely attached to the mount.
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MONITOR INSTALLATION
Attention
WARNING:
• Gas Spring Arm is under pressure and should be handled with care.
• Failure to follow the instructions may result in damage to the mount
and / or personal injury.
03

WARNING: This product contains small items that may pose a choking hazard.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
Technical Support at 1-800-651-9525 (US / CA), 44-808-196-3875 (UK) or
Customer Service at [email protected].
• NOTE: Not all hardware included in this package will be used.
Electric Drill (Optional)
Drill Bit (Optional)
3/8 - 1 1/16" (10 - 27mm)
Base USB Cable
Bolt
M4 x 10mm
Large Allen Key
3/16” (5mm)
USB Pressure Plate
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Step 1 Supplied Parts and Hardware
Step 2 Supplied Parts and Hardware
C-Clamp Brace C-Clamp
Bolt
M6 x 12mm Grommet Bolt
x 101 x 202 x 1Ax 2B
x 1M3
x 203 x 204 x 6Cx 1D
04

Arm Extender Arm
Small Allen Key
1/8” (3mm)
Large Allen Key
3/16” (5mm)Monitor Plate
Bolt
M8 x 38mm
Washer
16 x 8.2 x 1.5mm
Step 3 Supplied Parts and Hardware
Step 4 Supplied Parts and Hardware
Medium Allen Key
5/32” (4mm)Locking Plate Butterfly Nut
Washer
10 x 4.5 x 1.0mm
Spacer
L13mm
Bolt
M4 x 12mm
Bolt
M4 x 30mm
Large Allen Key
3/16” (5mm)
Step 5 Supplied Parts and Hardware
x 1Ex 1Fx 1M2
x 205 x 206 x 1M1
x 207 x 2Gx 2Hx 1M3
x 8Ix 8Jx 8Kx 8L
x 1M3
05

Step 6 Supplied Parts and Hardware
Step 8 Supplied Parts and Hardware
Step 9 Supplied Parts and Hardware
Step 11 Supplied Parts and Hardware
Large Allen Key
3/16” (5mm)
Large Allen Key
3/16” (5mm)
Large Allen Key
3/16” (5mm)
Small Allen Key
1/8” (3mm)
x 1M3
x 1M3
x 1M1
x 1M3
06

2A-1 Insert bolts [C] through C-clamp brace
[03] and thread into base [01]. Tighten with
medium Allen key [M2].
Route USB cables under base as
demonstrated in the following
diagram.
Use bolts [B] to attach USB
pressure plate [A] to hold the
USB cable in the base.
Option A: No USB Cable
Option B: Route USB Cable
Option A: For Clamp Mounting
Step 1 Attach the USB Cable
Step 2 Attach to Desk Mounting Surface
0101
0202
M3
M3
B
B
A
A
01
01
CC
03
03
M2
M2
07

2A-3 After pushing the clamp fully onto the desk, rotate the knob until the
C-clamp [04] is secured firmly to the underside of desktop.
2A-2 At an angle, guide the C-clamp [04] over the C-clamp brace [03] to desired
position then straighten the C-clamp [04] to be vertical.
0.4 - 3.5"
(10 - 90mm)
0.4 - 3.5"
(10 - 90mm)
Maximum
thickness:
3.5” (90mm)
0101 0101
0303
0404
0404
08

0.4 - 3.5"
(10 - 90mm)
0.4 - 3.5"
(10 - 90mm)
3/8" - 1 1/16"
(10 - 27mm)
NOTE: The hole should be
at least 2" (50mm) from
the edge of the desk.
2B-3 Slide locking plate [E] and butterfly nut [F] onto the grommet bolt and firmly
secure with butterfly nut [F].
2B-2 Screw grommet bolt [D] into the base, and then put it through the desk.
2B-1 If a hole is needed for grommet
installation, be sure to leave at least 2”
from the edge of desktop and mark where
the hole will be drilled. Use either a 3/8” or
1 1/16” drill bit for this step.
Electric Drill
(Not Included)
WARNING:
Ensure the grommet bolt is
threaded securely to the base.
Option B: For Grommet Mounting
DD
EE
FF
09

3-1 Push the arm extenders [05] into the base, and then the arms [06] onto the
arm extenders [05].
3-2 Tighten the set screws on both sides of the arm joints. Do not overtighten the
set screws as this may affect the rotation of the arm.
Step 3 Attach the Arm Sections
M1M1
0505
0606
M1M1
10

M3M3
H
H
G
G
07
07
Slide the monitor plates [07] sideways into the slot at the end of the arms [06].
Fasten with bolts [H] and washers [G].
Step 4 Attach the Monitor Plates
0707
0707
11

KK
IIII
KK0.1-0.2" (3-5mm)
spacing left
Turn clockwise to thread
Fig. A
For Monitor Hole Pattern:
100 x 100mm (3.9 x 3.9”)
For Monitor Hole Pattern:
75 x 75mm (3 x 3”)
Fig. B
Fig. C
5A-1 Thread two bolts [I] with washers [K] into the top holes until about 0.1-0.2"
(3-5mm) of space is left between monitor back and washer.
5A-2 Hang the monitor from the monitor plate with the top two bolts [I] (see Fig. A
or Fig. B). Screw the remaining two bolts [I] into the bottom holes (see Fig.C).
Tighten all bolts [I] evenly.
Step 5 Attach the Monitors to the Arms
Option A (For Flat Back Monitor)
II
II
II
KK
IIKK
KK
M3M3
KK
12

For Monitor Hole Pattern:
100 x 100mm (3.9 x 3.9”)
Fig. A
For Monitor Hole Pattern:
75 x 75mm (3 x 3”)
Fig. B
Fig. C
M3M3
0.1-0.2" (3-5mm)
spacing left
Option B (For Curved Back Monitor)
5B-1 Slide the washers [K] and spacers [L] over the bolts [J]. Turn the top two bolts
[J] CLOCKWISE until about 0.1-0.2" (3-5mm) of space is left between the washer
[K] and the spacer [L].
5B-2 Hang the monitor from the monitor plate with the top two bolts [J] (see Fig. A
or Fig. B). Place the spacers [L] between the monitor plate and back of monitor.
Screw the remaining two bolts [J] into the bottom holes (see Fig.C). Tighten all
bolts evenly.
KKLL
JJ
KKLL
JJJJKKLL
JJ
JJ
KKLL
KK
JJKK
LL
13

WARNING!
Gas Spring arm is under pressure
and should be handled with care.
Failure to follow the instructions
may result in damage to the
mount and / or personal injury.
NOTE: Ensure the arm is held in a
horizontal position (parallel to
desktop) during adjustment. Failing
to do so may result in difficulty
adjusting or potential damage to
the mount.
6-1 If the gas spring arm RISES with the
monitor attached, hold the arm in a
horizontal position while using the large
Allen key [M3] to turn the adjustment bolt
CLOCKWISE, REDUCING the arm tension.
6-2 If the gas spring arm LOWERS with the
monitor attached, hold the arm in a
horizontal position while using the large
Allen key [M3] to turn the adjustment bolt
COUNTER-CLOCKWISE, INCREASING the arm
tension.
Clockwise to
REDUCE tension
Counter-clockwise
to INCREASE tension
M3M3
Step 6 Adjust the Gas Spring Tension
14

M3M3
Incorrect orientation Correct orientation
To ensure proper stability, do not position monitor behind base. Monitor and arms
should remain over the desktop. Failure to do so may cause instability, resulting in
property damage or injury.
8-1 Slightly loosen the bolt with large Allen key [M3].
8-2 Tilt monitor to your desired position.
8-3 Re-tighten the bolt with large Allen key [M3] to hold monitor in desired position.
Step 7 Rotation Restriction
Step 8 Adjust the Monitor to Proper Tilt Angle
15

WARNING:
Do not overtighten or
overloosen the bolts.
180°180°
360°360°
360°360°
M1M1
M1M1
Turn adjustment set screw CLOCKWISE to INCREASE the swiveling tension.
Turn adjustment set screw COUNTER-CLOCKWISE to REDUCE the swiveling tension.
Step 9 Swivel Adjustment
16

360° Rotation
WARNING:
Ensure bolts are secured
firmly before rotation.
Firmly hold monitor at edges and rotate from Landscape to Portrait mode.
Step 10 Rotation Adjustment
17

①
②
⑤
④
③
①
②
⑤
④
③
Step 11 Route Cables along the Arm
M3M3
18

Thank you for choosing this ErGear product! At ErGear we
strive to provide you with the best quality products and
services in the industry. Should you have any issues, please
don't hesitate to contact us at
Technical Support:
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm (CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info:
[email protected]
Website:
https://ergear.com
860-00492-00 Rev00