Ergotron 97-487-800 User manual

1 of 7

888-97-057-W-00 rev. C • 08/19

CAUTION:

Product is shipped with a stop screw that MUST be removed before use.

DO NOT REMOVE STOP SCREW BEFORE ATTACHING KEYBOARD TRAY.

Failure too follow these instructions will cause equipment damage.

Auto Retractable Keyboard Assembly

for use with Ergotron products:

25-022

60-593

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

User's Guide

2 of 7

888-97-057-W-00 rev. C • 08/19

ABCDE

3/32"

3/16"

M4 x 12mm

8-32 x 1/4"

2.5mm

2x 2x2x

4x 1x

2.5 lbs

(1.14 kg)

<7"

(178 mm)

Max Weight Capacity

Depending on the design of your VL, you may need any one or combination

of these 4 tools to remove your keyboard tray and pivot.

Max Keyboard Depth

3/8"

Rear of Monitor

Centerline of Four-Hole

VESA FDMI Pattern

Minimizing Vertical Lift Storage Profile

For keyboard to fit under the monitor when in storage position, follow these guidelines:

Dimension “A”must be no greater than 7-7/8" (200 mm).

NOTE: Keyboard needs to attach to the lowest set of holes as shown in Step 3

3 of 7

888-97-057-W-00 rev. C • 08/19

Tighten all 4 screws

3/32" 2.5mm

Depending on the design

of your VL, you may need

any one or combination of

these 4 tools to remove your

keyboard tray and pivot.

Save these

screws for

use in steps

3a and 3c.

Attach pivot screws to

middle set of holes (third

up from the bottom

set) so pivot attaches at

lowest position.

3/8"

4 of 7

888-97-057-W-00 rev. C • 08/19

REMOVE STOP SCREW BEFORE USE.

M4 x 12mm

CAUTION:

Product is shipped with a stop screw

that MUST be removed before use.

DO NOT REMOVE STOP SCREW BEFORE

ATTACHING KEYBOARD TRAY.

Failure too follow these instructions will

cause equipment damage.

5 of 7

888-97-057-W-00 rev. C • 08/19

8aFollow these

instructions to tighten

or loosen tension.

1. Mount all Equipment

(keyboard, wrist rest,

mouse pad, mouse, ect.).

2. Tighten screw slowly

(turn clockwise) until tray

auto rises to full up position.

Screw may require several turns

Auto-rise Tension

abc

3/32"

Top tray must be

removed for pivot to

function properly.

Attach the loop (soft) side of the velcro to the

bottom of the mouse tray to eliminate rattle

when the tray is stowed upright.

Remove and discard.

Route mouse cable as shown.

8-32 x 1/4"

6 of 7

888-97-057-W-00 rev. C • 08/19

Lift – Up and down

It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is

added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and

optimum operation.

Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments are dicult and do not stay in the

desired position, follow the instructions to loosen or tighten the tension to create a smooth, easy adjustment motion. Depending on your product and the