ESBE GDA200 Series User manual

Dimensions ▯ Cabling Mounting position
SERIES FUNCTION
ESBE
GDA211
GDA 212
ESBE
GFA211
GFA212
GRA211
GRA212
GRA231
GRA232
GRC221
GRC222
GRC241
GRC242
ESBE
GBA211
Gxx2xx 100/10/1
0
5
15
Psi/bar/Mpa
+70
+58
+100
+110
+212Gxx2x1
+5
+41Gxx2xx
GRx2xx, GBA2xx
+32 0
+136
+55
+131
GDx2x1, GFx2x1
GDx2x2, GFx2x2 +158+158
+230Gxx2x2
Gxx2xx PN10
ESBE System Units
CIRCULATION UNIT DN25, DN32
Mtrl.nr. 98141121 Ritn.nr. 7951 vers. A• Rev. 2022‒12‒01
Series GDA200
Series GRA200
Series GFA200
Series GBA200
Series GRC200
125
321 58
250
0º
*
3
6
0
º
Pull
Pull
2Remove insulation
ESBE AB
Bruksgatan 22
SE‒333 75 Reftele
www.esbe.eu
Remove actuator/controller
Series GRA2xx, GBA211, GRC2xx
LVD 2014/35/EU
EMC 2014/30/EU
RoHS 2011/65/EU
ErP 2009/125/EU
PED 2014/68/EU, article 4.3
EnEV 2014
SI 2016 No. 1101
SI 2016 No. 1091
SI 2012 No. 3032
SI 2010 No. 2617
SI 2016 No. 1105

5
6
3
OUICK FIT!
Press
Press
»C
l
Click!
25°C22°C 33°C 40°C 47°C 54°C 60°C
https://esbe.eu/group/products/
thermostatic-mixing-valves
1
SERIES ARA600 Prop
Pro
P
SERIES ARA600 3-Point
S
ERIE
S
AR
A60
SERIES ARA600 2-Point
https://esbe.eu/group/
products/rotary-actuators
Commissioning actuator Commissioning
fixed temperature
Series GFA211, GFA212
CCWNCW
bkbu bn
L(bn)
N(bu)
PE (gn)
Electric installation
www.esbe.eu
SERIES VTA370/VTA570
Fit supply pipes
40-50Nm c/c 125mm
Adjust wallbracket
Assembling on wall 4
Assemble insulation
30mm
Assemble actuator/controller
Series GRA2xx, GBA211, GRC2xx
0
20 MINUTES
Commissioning
Flow
Filling and
venting
Open
White mark, indicate
check valve position
45
o
Filling and venting
Preparation
Open Closed
90
o
Checkvalve position
Flow
OPEN
AIR
CLOSE
Assemble removed knob

Wilo
= Factory settings
Factory setting
Variable differential
pressure - Δp-v
Constant differential
pressure - Δp-c
Constant speed
PUMP CURVE
I, II, III
CONTROL MODE
NORMAL
OPERATION FAULT
NORMAL
OPERATION
FAULT
CONTROL MODE
Variable differential
pressure - Δp-v
Constant differential
pressure - Δp-c
Constant speed
PUMP CURVE
I, II, III
Wilo Display
LED display
Hold
Hold
Status
Locked
8 sec
Unlocked
Factory
setting
Venting
1 sec
1 sec
10 min
Manual
restart
Factory
setting
30sec
Hold
8 sec
Hold
3 sec
Hold
6 sec
Hold
+
1.4.3.2.
LED
Indicator
Meaning Diagnostic Cause Remedy
lights green Pump in
operation
Pump runs
according its
setting
Normal operation
blinks red/
green
Pump in
function but
stopped
Pump restarts
by itself after
the fault is
disappeared
1. Undervoltage U<160 V
or Overvoltage U>253 V
2. Modul overheating:
temperatur inside motor
too high
1. Check voltage supply
195 V < U < 253 V
2. Check water and
ambient temperature
blinks red Pump out of
function
Pump stopped
(blocked)
Pump does not restart by
itself due to a permanent
failure
Change pump
blinks
orange
Pump out of
function
Pump stopped Pump is not starting Change pump
LED off No power
supply
No voltage on
electronics
1. Pump is not connected
to power supply
2. LED is damaged
3. Electronics are damaged
1. Check cable connection
2. Check if pump is running
3. Change pump
http://www.esbe.eu/global/en/
products/circulation units
WILO - Faults, Causes and
Remedies
LED displayclick Control mode Pump curve
Recomended
Alt.
1Constant speed II
Constant speed I
Variable differential III
Variable differential II
I
III
6
II
I
III
2
3
4
5
7
8
9
Click
Click
Recommended Alternative
LED display Control mode Pump curve
Constant speed
Constant speed
Variable differential
pressure Δp-v
Variable differential
pressure Δp-v
Variable differential
pressure Δp-v
Constant differential
pressure Δp-v
Constant differential
pressure Δp-v
Constant differential
pressure Δp-v
Constant speed
Settings navigationsPump Settings 6

Application
information
Expose application info using leaflet
6
7
Settings navigation
1
1
1
2
2
2
3
3
3
AUTOADAPT
AUTOADAPT
1
1
1
2
2
2
3
3
3
AUTOADAPT
AUTOADAPT
MODE UPM3 xx-50 UPM3 xx-70
MODE UPM3 xx-50 UPM3 xx-70
MODE UPM3 xx-50 UPM3 xx-70
MODE
FAULT DISPLAY SOLUTION
Wilo
Push button LEDs
Grundfos Display
http://www.esbe.eu/global/en/
products/circulation units
Grundfos - Faults, Display and
Solutions
No.2
2
1
ON
230 V
5 mm
0/Off
1/On
RED YELLOW
<160 V
ON
L
PE
N
RED YELLOW
2
3 4
230 V
ON 1
0/Off
1/On
RED YELLOW
OFF
0V
SYSTEM
CONTROLLER
PWM
AC
B
0/Off
1/On
L
PE
N