ZURN Sundara Z5003.01 User manual

Zurn Industries, LLC |Commercial Brass Operation
511 W. Freshwater Way, Milwaukee, WI U.S.A. 53204 · Ph. 1-855-ONE-ZURN, Fax [phone]
In Canada |Zurn Industries Limited
7900 Goreway Drive Unit 10, Brampton, Ontario L6T5W6 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. -
Date: 1/3/2018
C.N. No. SAN007500
Form No. FV611
Sundara®Drift Single Basin
Hand Washing System
Z5003.01
Sundara®Drift Single Basin
Hand Washing System
Installation, Maintenance,
and Parts Manual
PATENT(S)PENDING
LIMITEDWARRANTY
All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the
dateofpurchase.Decorativefinisheswarrantedforoneyear.Wewillreplaceatnocostsgoodsthatprovedefectiveprovidedweare
notified in writing of such defect and the goods are returned to us prepaid at Atlanta, GA, with evidence that they have been properly
maintainedand used in accordance with instructions.We shall not be responsible forany labor charges or any loss,injury or damages
whatsoever,includingincidentalorconsequentialdamages.Thesoleandexclusiveremedyshallbelimitedtothereplacementofthe
defectivegoods.Beforeinstallationanduse,thepurchaser shall determine thesuitabilityofthe product for hisintendeduseand the
purchaserassumes all risk and liability whatever in connection therewith. Where permittedby law, the implied warranty of merchantability
isexpresslyexcluded.If the products sold hereunder are “consumer products,” the implied warranty of merchantability islimitedtoa
period ofthree years andshall be limited solelyto the replacementof the defectivegoods. All weightsstated in ourcatalogs and lists are
approximateandarenotguaranteed.
NOTE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT.
NOTE: The information in this manual is subject to change at any time without notice. Installations may
be performed at different times of construction by different individuals. For this reason, these instructions
should be left on-site with the facility or maintenance manager.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov

FV611 Rev. - 1/3/2018
Page2
Overview:
Designed for modern commercial restrooms, the Sundara system delivers a superior user experience in both form and
function. Crafted by world-class industrial designers Sundara combines seamless basin designs with curated faucets
and soap dispensers, delivering a complete, easy to install hand washing solution.
Specifications:
Sundara®Drift single basin lavatory system manufactured by Zurn Industries. Lavatory shall be mounted at standard
height to conform with ANSI, UFAS, TAS and ADAAccessibility Standards. Counter and integral basin to be constructed of
Sundara®solid surface resin with aluminum trihydrate and other additives conforming to CSAB45.5/Z124 and IGC 156
standards. Shroud enclosure is constructed of satin finished type 304, 18 gage stainless steel designed for easy access
with vandal resistant hardware. Lavatory is furnished complete with 0.5 gpm laminar flow sensor operated faucet (specify
model) and optional liquid soap dispenser (specify model), ½” quarter turn supply stops, 3/8” flexible supply risers,
chrome 1 ¼” tail piece, and chrome 1 ¼” p-trap for complete system operation.
Paired Faucet Typical Specification
(Refer to faucet manual for more details on specific model)
Voltage: 6 VDC Series [4 “AA” (Alkaline or Lithium) and/or external power option]
Sensor Range: Self-calibrated, dependent upon sink depth and finish.
Operating Water Pressure: 10-125 psi
Operational Water Temperature: 33°F to 140°F (1°C to 60°C)
Aerator: 0.5 GPM Vandal-Resistant (Standard)
Paired Soap Dispenser Typical Specification
(Refer to soap dispenser manual for more details on specific model)
Power Supply: AC 110 V; DC 6V
Soap Viscosity: 100-3800 cps
Operating Temperature: 340- 1310F
Typical Dispensed Volume: 1.25 ml
Be sure the sink/lavatory/basin is clear from any objects upon making the sensor to electronics connection initiating the self-
calibration feature. The sink must be clear of any and all objects in order to calibrate appropriately (calibration time approx
30-60sec).
Prior to Installation:
• If applicable, carrier (Z1240 series) is installed behind the wall.
• Hot and cold water supply lines are installed as per building codes.
• Care shall be taken when installing this product to prevent damage of any exposed or decorative surfaces.
• Measure the drain outlet from the floor.
Important Safety Information:
• Installer is responsible for ensuring the product is installed and conforms to all plumbing codes and ordinances.
• Do not convert or modify this Zurn product yourself. All warranties will be voided.
• Water supply lines must be sized according to building design in order to provide adequate water supply for each fixture.
• Flush all water lines prior to making connections.
• Minimum 2 people required for the sink installation
•Au minimum, 2 personnes sont requises pour l’installation du lavabo.
S’assurer qu’aucun objet ne se trouve sur l’évier/le lavabo/le bac lors du branchement du capteur sur l’électronique, ce qui
lance la fonction d’auto-étalonnage. Rien ne doit se trouver sur le lavabo pour permettre son auto-étalonnage correct (temps
d’étalonnage de 30 à 60 s environ).

FV611 Rev. - 1/3/2018
Page3
Z5003.01 Parts List
Optional
5
6
9
8
7
4
ItemName QTY
1Basin 1
2 Shroud Wall Bracket 1
3Shroud 1
4Mounting(L)Bracket 2
5 Wall HangerBracket
(Available only for Retrofit) 1
6Griddrain 1
7 Water Supply Items 2
8 Drain Adapter Assembly 1
9 P Trap Assembly 1
10 Sensor Faucet 1
11 Soap Dispenser (If Ordered) 1
12 5/16-18 Screw for Mounti ng
L Bracket to Basin 4
13 #10-24 Screw for Drain Adapter and
Shroud 6
14 #6-32Screw for Grid Drain 2
15 Coarse Screw for Wall Bracket 2
16 Flanged Socket Head Screw for Shroud 2
17 Oversi ze 5/16 Washe
r
4
18 #10 Flat Washer for Drain Adapter and
Shroud 8
19 3/8-16 Hex Bol t with washer 14
20 3/8" Toggl e Never Drop Anchor 14
21 3/8 Fender Washe
r
8

FV611 Rev. - 1/3/2018
Page4
Plumbing and Electrical Rough-Ins
34 [863]
291
2[752]
283
4[733]
143
4[378]
11
4[29]
191
2[493]
29 [735]
11
2[36]
21
4[57]
73
4[195] 73 4[195]
21
4[57] 16 [404]
5 [124]
Note: Installing the P-trap outlet lower than 19.5” from finished
floor will prevent the vandal shroud from being installed.

FV611 Rev. - 1/3/2018
Page5
L Brackets Installation
Required Tools:
Drain Adapter Assembly
Installation
12
17
13
18
Torx Wrench:
T10 & T25 Socket Wrench: 5/16” & 3/8” Non-toothed Wrench
Allen Wrench:
3mm
For ease of installation, lay basin on its top surface on a
cushioned surface.
Use socket wrench to torque the screws (approximately 4-5
complete turns bottom out approximately 5 ft-lbs of torque).
Warning: Do not overtighten the screws.
Avertissement : ne pas trop serrer les vis.
For ease of installation, lay basin on its top surface on a
cushioned surface.
Use T25 torx wrench to torque the screws (approximately 4-
5 complete turns and squeeze the gasket, approximately 2-
3 ft-lbs of torque).
Warning: Do not overtighten the screws.
Avertissement : ne pas trop serrer les vis.

FV611 Rev. - 1/3/2018
Page6
Installing Mounting Bracket
•Securethe mountingbrackettotheplywood cut-outwith suppliedwashers, boltsand toggleanchors on
theplywood.
Retrofitting Hanger Bracket
Installation
1 [25]
31
2[89]
4 [99]31
2[89]
21
19
20
Plywood
Wall Stud
Bolt supplied by
installer to attach
the plywood to
wall studs
Hanger
Bracket
Mounting
Bracket
21
19
20
Plywood
Wall Stud
Bolt supplied by
installer to attach
the plywood to
wall studs
Recommended for retrofit:
• Measure the rough in dimensions on the wall. Top edge of
the cutout marked must be 2” below the basin top back
edge.
• Cut the drywall to suitable size (30”x20”) and attach a
minimum of 1/2” thick plywood to the wall stud and flush
to the drywall.
•Drill four ¾” holes in the plywood at the locations shown
in the graphic to the left. Then, install the supplied toggle
anchors to wall and secure the hanger bracket(s) directly
to the plywood with the supplied bolts.
• Installhanger bracket to wallperstructural rough-in.
• Theplywoodshould not be visible afterbasinandshroud
installation.
• Thebracket needs to be checkedfor level after
installation.
Warning: Must be handled by at least 2 people
Warning: Ensure the basin back edge is completely supported in the wall bracket.
Avertissement : s’y prendre à deux minimum.
Avertissement : s’assurer que le bord arrière du bac est complètement soutenu par le support mural.

FV611 Rev. - 1/3/2018
Page7
Installing with Carrier Option
Faucet Installation
Refer to faucet installation guide for details.
Warning: Must be handled by at least 2 people
Avertissement : s’y prendre à deux minimum.
Refer to Carrier Rough-in & Installation guide for details.

FV611 Rev. - 1/3/2018
Page8
Soap Dispenser Bracket
and Bottle Installation
Refer to soap dispenser installation guide for details.
Soap Dispenser Installation
Install the soap spout on right or left as applicable.
Refer to soap dispenser installation guide for details.

FV611 Rev. - 1/3/2018
Page9
P Trap Installation & Water
Supply Connection to Faucet
Adjust the tail piece base on drain outlet on the wall.
Grid Drain Installation
14
Connect the tail piece
to drain adapter
(threaded connection)
Shroud Installation:
Step 1
•Align wall bracket as shown and install coarse screw
on each side. Mark the slots in the wall bracket on the wall.
15
9
615
Use T10 Torx wrench to attach the grid drain to basin.
Torque screws until the screw heads are flushed with the
screw pocket of grid drain.
Warning: Do not overtighten the screws.
Avertissement : ne pas trop serrer les vis.
Suggested Final Step: Caulk/Silicon lavatory to the finished
wall for a water tight seal.

FV611 Rev. - 1/3/2018
Page10
Shroud Installation:
Step 2 Step 3
Step 4 Step 5
•Remove the wall bracket and drill 3/4” holes into the
center of the holes previously marked. (Note: For installa-
tion with carrier, do NOT drill the two outside holes. For
retrofit applications, the two outside holes are recom-
mended.) Ensure that wall studs are not immediately
behind the marked hole locations prior to drilling.
•Install anchor toggle bolts into previously drilled holes
in walls.
•Re-install wall bracket with coarse screws in previous
location. Then, fasten the wall bracket with 3/8” bolts
through each holes and into the toggle bolts.
•Place shroud on hanger hooks of wall bracket as
shown. Then, position the pivot of the shroud through the
hole in the wall bracket. (Note: the shroud will likely need to
be rotated upward slightly in order to install each pivot.
•After one pivot is installed, fasten the flange screw into
the pivot with the 3mm allen wrench. Then repeat this step
for the other side
•Rotate the shroud up to the basin until the threaded
hole in the L-bracket in visible through the slot in the
shroud. Then, install the screw shown, and repeat for the
other side.
16
19
13
20