American Standard ARCH 4101.100 User manual

M968586 Rev. 1.5
SINGLE CONTROL
KITCHEN PULL-OUT FAUCET
Installation
Instructions
Certified to comply with ANSI A112.18.1M
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
ARCH™
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the screws
slightly each time until all are snug to ensure even pressure.
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (3) from underside of
sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the screws
slightly each time until all are snug to ensure even pressure.
Installation with ESCUTCHEON: Figure A. Apply a light bead of plumbers putty to underside of ESCUTCHEON (1) if
mounting surface is uneven. Insert SEAL (1) into groove at base of faucet. Insert supply HOSES (2) and SHANK (3)
through ESCUTCHEON (4) and mounting surface.
Installation for single hole mounting: Figure B. Insert SEAL (10) into groove at base of ESCUTCHEON (11).Insert
SEAL (1) into groove at base of faucet. Insert supply HOSES (2) and SHANK (3) through ESCUTCHEON (11) and mounting surface.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
RECOMMENDED
TOOLS
Adjustable Wrench Regular Screwdriver Phillips Screwdriver
Turn off water at
main supply.
CAUTION
SINK OR
MOUNTING
SURFACE
SINK OR
MOUNTING
SURFACE
GROOVE IN FAUCET
GROOVE IN FAUCET
GROOVE IN ESCUTCHEON
10
11
87
5
7
9
6
4
33
1
87
1
5
7
9
6
22
Figure A Figure B
Channel Locks
4101.100
4101.100F15

M968586 Rev. 1.5
2MAKE WATER SUPPLY CONNECTIONS
3CONNECT SPRAY HOSE AND INSTALL WEIGHTS
With PULL-OUT SPRAY (1) seated in FAUCET (2),
install WEIGHT (3) onto HOSE (4) using SCREW (5).
Locate the WEIGHT (3) two feet (2') from the underside
of the sink deck.Tighten SCREW (5) firmly.
Make sure SEAL WASHER (7) is installed in COUPLING
NUT (6). Connect threaded end of HOSE (4) to SPRAY HOSE
COUPLING NUT (6) from fitting. Use wrench to tighten.
1
2
COLD
HOT
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
4
6
7
1
2
24"
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE (1) down into "off" position.
Turn on water supplies and check connections
for leaks.
CHECK CONNECTIONS
FOR LEAKS
4
1
53

M968586 Rev. 1.5
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then: 1
2
3
4
7
5TEST INSTALLED FAUCET
Move HANDLE (1) down into "off" position.
With HANDLE (1) down in "off" position, pull HAND SPRAY (2)
from FAUCET (3). SPRAY (HOSE (5) should pull approximately 2 feet
and direct open SPRAY END (2) into sink.
Turn on water supplies. Check connections for leaks.
Operate handle up and down, in COLD and HOT positions,
to flush water lines thoroughly.
Place HAND SPRAY (2) back into FAUCET (3).
Check HAND SPRAY (2) operation:
With faucet on push BUTTON (4) for a broad cleansing
spray. BUTTON (4) will lock into this position.
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
Test fitting.
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
1
To unlock push opposite end of BUTTON (4). Faucet will
return to standard spray. 2
4
3
5
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
5
6
8
9
7
6a
AERATOR (9) may accumulate dirt causing distorted and reduced water
flow. Remove AERATOR (9) and rinse clean.

M962146-0070A
MOUNTING KIT
M968586 R e v. 1. 5
MODEL NUMBERS
M962721-YYY0A
SINGLE HOLE
ESCUTCHEON KIT
M918506-0070A
CARTRIDGE SCREWS
M962732-YYY0A
ESCUTCHEON KIT
A951470-0070A
CARTRIDGE
M911261-0070A
SEAL
SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
M962716-0070A
BUTTON AN D
SCREW KI T
M907302-YYY0A
ESCUTCHEON CAP
M962717-YYY0A
HANDLE KIT
CHROME
STAINLESS STEEL
002
075
Replace the "YYY" with
appropriate finish code
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are t rademarks of American Standard Inc .
© AS America, Inc. 200 8
HOT LINE FOR HELP
ARCH™
M964395-0070A
WEIGHTS
4101.100
4101.100F15
M953173-YYY220A
(2.2 GPM) SPRAY
M953173-YYY150A
(1.5 GPM) SPRAY