ESCALADE Stiga T8631F User manual

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together.
Leave bolts slightly loose until you are instructed to tighten them.
4. Tools required for assembly: Allen Wrench T1 & Wrench T2(included), 10mm Wrench is helpful and
5. An electric screwdriver is recommended in assembly. However, please set at low torgue and use
extreme caution with an electric screwdriver because you could overtighten the hardware andstrip
the screws.
6. To make assembly as easy as possible, place all parts of the table tennis table in a cleared area and
remove the packaging material. Organize all parts as per parts identifier in the assembly manual.
Do not dispose of the packing materialuntil assembly is completed.
7. Avoid scratching table tennis top and metal tube parts during the assembly process.
8. Assemble product on a clean, level and flat surface.
9. Taketime to correctly orientate parts exactly as per each assembly diagram.
10. Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
OWNER’S MANUAL
Please visit our website at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMANTION
R
Escalade Sport products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2023 Escalade Sports
R
C
R
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [e-mail]
R
READ ASSEMBLY, OPERATING AND SAFETY INSTRUCTIONS
CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED TO PUT
THIS TABLE TOGETHER!
Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as
Manufacturing defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT
TO THE STORE!
Mailing Address
(correspondence only):
Escalade Sports
PO Box 889, Evansville, IN 47706
Be sure to write your model number and serial number
here for future reference. You can find these numbers
printed on the bottom of the table.
MODEL NO.: T8631F
DATE CODE : CPSIA#2-T8631F-____-SY
PURCHASE DATE : _____________________
Please provide model number and/or part number of the product and/or part when you call or write. These numbers can be found on the
product, packaging, and/or in this Owner’s Manual.
Phillips Screwdriver.
Physical Location:
Escalade Sports
817 Maxwell Ave.
Evansville, IN 47711
CAUTION:

- 2 -
HARDWARE IDENTIFIER (To Scale)
H6 - 5mm x 13mm
Phillips Round Head
Screw (36 pcs)
H1 - 6mm x 60mm
Allen Head Bolt
(8 pcs)
H4 - 6mm x 55mm
Allen Head Bolt
(8 pcs)
H2 - 6mm x 18mm
Flat Washer
(36 pcs)
H7 - 6mm x 10mm
Plastic Spacer
(8 pcs)
H3 - 6mm
Lock Nut
(18 pcs)
H8 - Shoulder Washer
(2 pcs)
T1 - Allen
Wrench (1 pc)
T2 - Wrench (1 pc)
(Not to Scale)(Not to Scale)
H5 - 6mm x 45mm
Allen Head Bolt
(2 pcs)

P1 - Half Table Tennis
Table Assembled
(2 pcs)
P2 -
Inner U-Support
with Caster Sockets
installed (2 pcs)
P3 -
Plastic Leg Panel
with Frame (2 pcs)
P4 - U-Clip Bracket
(6 pcs)
P5 - Caster without Lock
(4 pcs)
P6 - Safety Latch
(2 pcs)
P7 - Linkage Tube with
Stop Bracket (2 pcs)
- 3 -
PARTS IDENTIFIER (Not to Scale)
P8 - Linkage Tube
(2 pcs)
P9 - Net
(1 pc)
P10 - Net Post
(2 pcs)

- 4 -
PARTS REQUIRED
36 pcs - H6 Phillips Round Head Screw
2 pcs - P1 Half Table Tennis Table
2 pcs - P2 Inner U-Support with Caster Socket Installed
Mounting Holes
on this side
IMPORTANT NOTE: Table halves must be laid on a clean flat surface for correct assembly and to prevent any scratches or
blemishes to playing surface. As bottom of table halves have many predrilled pilot holes - please make sure to match all
parts to the correct pilot holes.
IMPORTANT NOTE:
1. BE SURE THAT SLOT IN THE THREE P4 U-CLIP
BRACKETS ALL FACE THE SAME DIRECTION
(TOWARD THE MIDDLE OF THE TABLE) AS SHOWN IN
FIGURE 1 & DETAIL A.
2. BE SURE TO ALIGN THE THREE P4 U-CLIP BRACKETS
WITH PRE-DRILLED PILOT HOLES IN TABLE TOP
ASSEMBLY BEFORE SECURING WITH H6 SCREWS.
3. BE SURE THE THREE P4 U-CLIP BRACKETS ATTACH
TO THE SMALL LOCATING PIN ON P2 U-SUPPORT AS
SHOWN IN FIGURE 1 & DETAIL B.
This end is the middle of
the table and does not
have white screen lines
DETAIL A
Slot in U-Clip
P4
P4
P1
This end is the
middle of the table
and does not have
white screen lines
FIGURE 1
P4
P2
H6
H6
P4
DETAIL B
Slot in U-Clip
Locating
Pin
Middle Side
Slots All Face
Middle Side Of Table
Middle Of Table Is The
“Net” Side
P4 - U-Clip Bracket
(Pre-Installed)
6 pcs - P4 U-Clip Bracket
P4
STEP 1:
Attach each P2 Inner U-Support Leg to P1 Table using
three pieces P4 U-Clip Brackets and pre-drilled pilot holes
with H6 Screws.
Repeat procedure for the other table half assembly.
Note: Be careful not to strip these screws - All H6
screws must be tight - but not stripped.
NOTICE:
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT
THAT THE P4 U-CLIPS BRACKET BE TURNED AS SHOWN
IN FIGURE 1 & DETAIL A.
IF U-CLIPS ARE TURN INCORRECTLY, YOU WILL DO
IRREPARABLE DAMAGE TO YOUR TABLE WHEN YOU
ATTEMPT TO OPEN IT TO THE PLAYING POSITION.

- 5 -
PARTS REQUIRED
8 pcs - H4 6mm x 55mm 16 pcs - H2 Flat Washer 2 pcs - P7 Linkage Tube with Stop Bracket
Allen Head Bolt H7 Plastic Spacer 2 pcs - P8 Linkage Tube
8 pcs - H3 Lock Nut 1 pc - T1 Allen Wrench
STEP 2:
Attach one end of P7 Linkage Tube with Stop Bracket to OUTSIDE of P2 Inner U-Support using H4 Bolt, H2 Flat Washers, H7 Plastic
Spacer and H3 Lock Nut as shown in DETAIL C.
Attach one end of P8 Linkage Tube to OUTSIDE of P2 Inner U-Support using H4 Bolt, H2 Flat Washers, H7 Plastic Spacer and
H3 Lock Nut as shown in FIGURE 2.
Attach the other end of P7 Linkage Tube with Stop Bracket to INSIDE of C2 Outer Curved Leg using H4 Bolt, H2 Flat Washers,
H7 Plastic Spacer and H3 Lock Nuts as shown in DETAIL D.
Attach the other end of P8 Linkage Tube to INSIDE of C2 Outer Curved Leg using H4 Bolt, H2 Flat Washers, H7 Plastic Spacer and
H3 Lock Nuts as shown in FIGURE 2..
Repeat procedure for the other table half assembly.
IMPORTANT NOTE:
- Be sure to use the "bottom hole" in
P2 U-Support for H4/P7 and P8 assembly.
- Tighten hardware snug enough to keep
table stable but do not overtighten.
Tubes must pivot freely.
P1
This end is the
middle of the table
and does not have
white screen lines
FIGURE 2
H4
H2
H7
H2
H3
P7
H2
H4
H7
H2
H3
H2
H4
H7
H2
H3
P7
DETAIL C
H2
H7
H3
H2
H4
P8
H2
H4
H7
H2 H3
H4
H2
H7
H2
H3
P2
P7
C2
DETAIL D
End of P8 Linkage must
be placed OUTSIDE of
P2 U-Support
End of P7 Linkage must
be placed OUTSIDE of
P2 U-Support
End of P8 Linkage
must be placed
INSIDE of C2 Leg
End of P7 Linkage
must be placed
INSIDE of C2 Leg
C2
P2
Small hole must face
towards CENTER of
table
Small hole must face
towards CENTER of
table Small hole must face
towards CENTER of
table
Small Hole must face
towards OUTSIDE of
table
T2 Wrench1 pc -
8 pcs -
H2

- 6 -
PARTS REQUIRED
4 pcs - H1 Allen Head Bolt 4 pcs - P5 Caster without Lock
8 pcs - H2 Flat Washer 2 pcs - P3 Plastic Leg Panel with Frame
STEP 3:
Insert two pieces P5 Casters into each C4 Caster Socket as shown in FIGURE 3. Caster must “snap” down into Caster Socket.
Repeat procedure for the other table half assembly.
Note: Be sure P5 Casters are installed completely into C4 Caster Sockets.
Attach two pieces P3 Plastic Leg Panel with Frame to the P2 U-Support using H1 Allen Head Bolts with H2 Flat Washers and
Lock Nuts as shown in FIGURE 3..
Note: Logo label face outside and is upside down at this point of assembly.
This end is the
middle of the table
and does not have
white screen lines
FIGURE 3
P3
H2
H1
P3
Logo label face
OUTSIDE and
UPSIDE DOWN.
C4
Caster Sockets
(Pre-Installed)
P5
P5
P2
P2
Logo label face
OUTSIDE and
UPSIDE DOWN.
H2
H1
4 pcs - H3 Lock Nut
H3
H2
H2
H1
H2
H2
H3
H2
H3
C3
Corner Protector
(Pre-Installed)
C2
Curved Leg
(Pre-Installed)
C1
Leg Plastic Cap
(Pre-Installed)
C4
Caster Sockets
(Pre-Installed)
C1
Leg Plastic Cap
(Pre-Installed)

- 7 -
PARTS REQUIRED
4 pcs - H1 Allen Head Bolt
8 pcs - H2 Flat Washer
STEP 4:
Make sure the legs on one table top half (the half with P3 Plastic Leg Panel attached) are open.
With one person on each side of the table, lift and set table half on its legs. Place table against a wall as shown to help stabilize table
top half while another table half (the half without P3 Plastic Leg Panel) is being attached.
Be sure there is enough room to connect table half without P3 Plastic Leg Panel.
Next, With a person on both sides of the table half without P3 Plastic Leg Panel, slide the table half without P3 Plastic Leg Panel
against the table half with P3 Plastic Leg Panel attached.
Next, Secure the table half together using four pieces H1 Allen Head Bolts with H2 Flat Washers and Lock Nuts as shown in
FIGURE 4. Tighten all H1 bolts on this time.
FIGURE 4
Place This Half
Against A Wall
Table Half with
Plastic Leg Panel
Attached
Table Half without
Plastic Leg Panel
Attached
H1
H2
P3
P2
4 pcs - H3 Lock Nut
H3
H2
H3
H2
H3
CAUTION:
CAUTION:
WARNING:
THIS STEP REQUIRES THREE OR MORE ADULTS.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON ITS LEGS.
BE CAREFUL, THE TABLE IS VERY HEAVY.
BE SURE TABLE HALF WITH P3 PLASTIC LEG PANEL IS STABLE AND AGAINST A WALL.
DO NOT LEAVE TABLE HALF STANDING UNATTENDED.
UNTIL THE TABLE HALVES ARE CONNECTED THEY WILL NOT STAND ON THIER OWN.
IT IS RECOMMENDED TO HAVE THREE PEOPLE TO CONNECT TABLE HALVES.
TWO TO STABILIZE TABLE AND ONE TO BOLT TABLE TOGETHER.

- 8 -
PARTS REQUIRED
2 pcs - H5 Allen Head Bolt 2 pcs - H8 Shoulder Washer 1 pc - P10 Net Post
4 pcs - H2 Flat Washer 2 pcs - P6 Safety Latch 1 pc - T1 Allen Wrench
2 pcs - H3 Lock Nut 2 pcs - P9 Net
STEP 5:
Attach one piece P6 Safety Latch into the right-hand hole on the P2 Inner U-Support using one piece H5 Bolt, two pieces H2 Washers,
one piece H8 Shoulder Washer and one piece H3 Lock Nut as shown in FIGURE 5, FIGURE 6 and DETAIL E.
Next, Go to the other side of the table and attach the second P6 Safety Latch into the right-hand hole on the other P2 Inner U-Support
using one piece H5 Bolt, two pieces H2 Washers, one piece H8 Shoulder Washer and one piece H3 Lock Nut as shown in FIGURE 5,
FIGURE 6 and DETAIL F .
Next, Attach P10 Net Posts and P9 Net as shown in FIGURE 5 and DETAIL G.
FIGURE 5 P10
P9
DETAIL G
IMPORTANT NOTE:
1. SAFETY LATCHES MUST PIVOT FREELY.
2. SAFETY LATCHES MUST BE ATTACHED
DIAGONALLY ACROSS FROM EACH OTHER
AS SHOWN IN FIGURE 6.
H5 H2
H8 P6
H2
H3
FIGURE 6
P6 Safety Latch
(in right-hand hole)
P2
P6 Safety Latch
(in right-hand hole)
P2
DETAIL E
H8
P6 H2 H3
H2H5
P2
DETAIL F
P2
P6 H8
H3 H2 H2 H5
T2 Wrench1 pc -
CAUTION:
INSTALL P6 - SAFETY LATCHES AS SHOWN FOR PROPER USE OF TABLE!
DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY LATCHES ARE
INSTALLED AND ASSEMBLY IS COMPLETE!

- 9 -
TO OPEN:
1. Pull both legs away from table slightly.
2. Stand behind the table near the safety latch.
3. Hold table half with one hand and pivot safety latch enough
to allow the edge of the table half to pass over it.
4. While keeping an eye on the safety latch, pivot table half
until it moves past the safety latch. Once edge of table has
passed over safety latch, stop pivoting table half.
5. With both hands on the table half, center yourself along the
table half and lower the table half to the floor.
6. Repeat for the other table half.
OPENING AND CLOSING INSTRUCTIONS
TO CLOSE:
1. Lift table half upward and inward to vertical position.
2. Check to be sure the table half is locked in the safety latch.
3. Repeat for the other table half.
CAUTION:
THIS IS GAME TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP
ON THE TABLE! FAILURE TO COMPLY WITH THIS CAUTION COULD
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
See
Detail
Views
Pivot safety latch
until table edge can
pass over it.
Table edge passes
over safety latch.
CAUTION:
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO NOT ALLOW CHILDREN
TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON TABLE! SERIOUS OR FATAL INJURY MAY RESULT!
THIS IS NOT A TOY! TABLE IS TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY OR PROPER DAMAGE.

- 10 -
CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple
maintenance steps, you will add to the life of your new table.
The top (playing surface) of your table is made of Mid-Density Board.. Like all products made of wood, it
can be affected by atmospheric changes in both temperature and humidity. This may cause a slight
sag or distortion as the top expands or contracts. This is normal and should not cause concern as it
does not detract from the play or utility value of the table. After assembly of the table, you can minimize
the effects of temperature and humidity changes by storing the table in a dry area when table is not
in use.
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes can cause the wood to warp, swell, crack or blister. When your table is not in
use, it should be stored in a dry area. Due to the nature of particle board, table top may bow.
Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
THE TABLE TOP
STORAGE OF YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table’s playing
surface, DO NOT USE ANY CHEMICALS, ABRASIVE OR CLEANING PRODUCTS on your table’s playing
surface.
CLEANING YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease
of use of your table.
MAINTENANCE OF YOUR TABLE
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING
POSITION and move table several inches in different directions to find the best location for the table.
If the floor is extremely unlevel, table may not play or operate properly.
If table is high in the center, shim upunder the outer curved legs.
UNLEVEL FLOORS
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes which occur on patios or similar areas can cause wood to warp, swell, crack or
blister.
PRODUCT PARTS LIST - T8631
Key# Part# Description Qty.
H1
H3 T8631SYH3 6mm Lock Nut 18
H5 T8631SYH5 6mm x 45mm
H7 T8631SYH7 6mm x 10mm Plastic Spacer 8
H8 T8631SYH8 Shoulder Washer 2
T1 T8631SYT1 Allen Wrench
Key# Part# Description Qty.
Sockets Installed 2
P3 T8631SYP3 Plastic Leg Panel with Frame 2
P4 T8631SYP4 U-Clip Bracket 6
P5 T8631SYP5 Caster without Lock 4
P6 T8631SYP6 Safety Latch 2
C4 T8631SYC4 Caster Socket (Pre-Installed) 4
M1 T8631SYM1 Owner’s Manual 1
K1 T8631SYK1 Hardware Kit 1
2
T2 T8631SYT2 Wrench 1
1
H4 T8631SYH4 6mm x 55mm
8
P7 T8631SYP7 Linkage Tube with Stop Bracket 2
P8 T8631SYP8 Linkage Tube 2
P9 T8631SYP9 Net 1
P10 T8631SYP10 Net Post 2
C1 T8631SYC1 Leg Plastic Cap (Pre-Installed) 4
C2 T8631SYC2 Curved Leg (Pre-Installed) 2
C3 T8631SYC3 Corner Protector (Pre-Installed) 4

- 11 -
90 DAY LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the “Product”).
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of
ninety (90) days from the original purchase.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall
repair or replace withacomparable model, and Product, or component thereof, which may prove
defective under normal use and proper care, and which our examination shall disclose to our
satisfaction to be thus defective, please contact our Warranty Dept.
R
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any
Product of its manufacture is free from defects in material and workmanship when used for the intended
purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED
BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS
PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND
R
WORKMANSHIP.
R
1-800-467-1421 / Warranty Dept.
Or Write us at:
Escalade Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[e-mail]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty
Produts. ESCALADE SPORTS strongly recommends that the Product is insured for value prior to mailing.
R
R
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE ABOVE NINETY (90) DAY WARRANTY PERIOD. ESCALADE SPORTS SHALL
NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS,
EXPENSES OR DAMAGES INCURRED BY THE CONSUMER OF ANY OTHER USE.
R
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental
damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty give you specific legal rights and you may also have other rights which
may vary from state to state.
NOT COVERED BY THIS WARRANTY:
- Product not intended to be in places of public assembly, such as, but not limited to, schools, parks,
public or private recreational facilities.
- Any product subjected to Non-residential abuse, negligence, improper installatin, vandalism, acts
of God, alteration of product, or any other events beyond the control of ESCALADE SPORTS.