ESI Solution 6CC Quick start guide

INSTALLATION AND USE
Solution 6CC
ARTICULATING ARM and
KEYBOARD PLATFORM
SOLUTION 6CC Rev A 4/17
SOLUTION 6CC
Model SOLUTION 6CC

2
Tape to Underside
of Work Surface
SOLUTION 6CC
PLEASE REVIEW these instructions before beginning the installation. Check that
all parts needed were provided with your order. Contact your supplier if any
operates to your satisfaction.
Solution 6CC combines the AA750DAT articulating arm with the PL003CC-27
keyboard platform. In this instruction booklet, installation of the two products
will be explained in sequence, beginning with the AA750DAT.
AA750DAT PARTS PROVIDED
CAUTION: This install
T RACK MOUN T IN G T EM P LA T E
FRONT EDG E OF WO RK S UR FA CE
1. Tape thismountingtemplate
to
th
e underside ofwork surface.
2. Drilltwo(2) 1/8" diameterx 1/2" deeppilotholes at markedlocations. Be careful notto
drillthroughth
e worksurface.
3. Remove templateandinstalltwo(2) #12 x 3/4" woodscrews intopilotholes. Leavea gap
ofapproxim
ate
ly 1/8" betweenthe head of each screw
andwork surface.
4. Slidetrack ontoscrews, usingthe keyholes inthe track. Tightenth
e screws andinstall
additionalscrews as required, minimum of four (4).
Note:Ifkeyboardtray is deeperthan12", mount baseframea further 1/2" back from
thefron
t
edgeofwork surface.
1/8" PilotHole
1/8" PilotHole
Articulating Arm (1) Track (1)
12x3/4" Screws (8)
10x3/8" Self TappingFront Stop (1)Template (1)
ADDITIONAL TOOLS REQUIRED
•
STEP 1: Use Template to Drill Pilot Holes
• Tape the template to the underside of the work
surface. Align the “front edge” line on the
template with the front edge of the
work surface.
• Drill 1
/8" pilot holes 5/8" deep
through the two marked
locations on the template.
CAUTION: Be careful not to drill
through the top of the work surface.
Screws (2)
• Drill with 1 /8" bit #3 Phillips drill bit •#2 square Phillips bit
requires a power tool or
cordless drill. This is not a
handtool install.

3
SOLUTION 6CC
STEP 2: Attach Track
• Remove the template and install two 3/4" wood screws into the pilot holes.
— Leave a gap of approximately 1 /8" between the head of each screw and
the work surface
• Slide the track onto the screws, using the keyholes in the track. Tighten the
screws.
• Drill pilot holes for six additional screws spaced evenly along the track.
Fasten the screws to complete the installation of the track.
Slide Small Portion
of Keyhole Under
Screw and Tighten
1
/8"

4
Begin keyboard installation with STEP 5 on page 5.
SOLUTION 6CC
Slide Back
STEP 3: Install Articulating Arm
• Slide the articulating arm onto the track.
Position it back far enough so that
you have access to the front two
recessed holes on the track.
STEP 4: Attach Front Stop
• Position the front stop onto the
front of the track and secure it
with the 3/8" machine screws.
Front
Stop
3/8"Machine
Screw

5
Panhead
Screw
SOLUTION 6CC
The keyboard platform for Solution 6CC is the 27" wide PL003CC-27. Its cut
corner design works well with straight edge, large radius, and corner diagonal
work surfaces.
PL003CC-27 PARTS PROVIDED
Keyboard Platform (1) Palm Rest (2)
1 Each for
Keying and Mousing
Flathead Screw (4) Flange Nut (4) Cord Clips (2)Panhead Screw (4)
#8-32x1
/2#8x32 #8-32x5
/8
(R-Series: #8-32x3 /4)
CAUTION:
Hand-tighten screws only. Do not use power tools.
ADDITIONAL TOOLS REQUIRED
• Phillips screwdriver
STEP 5: Attach Palm Rests
• Attach the palm rests to the keyboard platform.
Use the #8-32x5
/8panhead screws (#8-32x3 /4
with the R-Series) and a Phillips screwdriver.
Six screw holes are located in the keyboard
platform to accommodate the choice
of palm rest installations.
— Attach each palm rest with
two screws through the two
end holes.
— The mouse and keyboard
palm rests may be attached
on either the left or right sides
of the keyboard platform.

6
SOLUTION 6CC
STEP 6: Attach Keyboard Platform
• Attach the keyboard platform to the keyboard arm and track assembly
using the four athead screws and ange nuts.
— Be sure the ange on the nuts is facing upward.
IMPORTANT: The ange nuts must be fully tightened to ensure the nuts are
locked. Use a Phillips screwdriver.
Flathead
Screw
Flange
Nut
Flathead
Screw
Flange
Nut

SOLUTION 6CC
STEP 7: Manage Cables
• Adhere cord clips to the underside of
the keyboard platform as needed to
organize the keyboard and mouse
cables.
Cord Clip
OPERATION
To Raise:
• Grasp both sides of the platform and raise
to the desired height.
To Lower:
• Grasp both sides of the platform, tilt up the front, and move down to the
desired height.
To Tilt:
• Turn the handle clockwise to tilt the platform up.
• Turn the handle counterclockwise to tilt the platform down.
© 2017 ESI Ergonomic Solutions. All rights reserved. SOLUTION 6CC Rev A 4/17
800.833.3746 esiergo.com