ESP EnVision EV-12010 BR User manual

© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com / UM-enVision-Rev-H
User Manual
120 and 208-240 Volt Models

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 1

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 2
I. PRODUCT OVERVIEW.........................................................................................................4
1. MODELS...........................................................................................................................4
2. KEY FEATURES.................................................................................................................4
3. TECHNICAL SUPPORT ........................................................................................................4
II. INSTALLATION INSTRUCTIONS........................................................................................5
1. FILTER INSTALLATION........................................................................................................5
a. TURN OFF EQUIPMENT..................................................................................................5
b. CONNECT MODEM/FAX LINE..........................................................................................5
c. CONNECT 10/100/1000 ETHERNET NETWORK LINE ........................................................5
d. CONNECT EQUIPMENT ..................................................................................................6
e. CONNECT FILTER TO OUTLET.........................................................................................7
III. HARDWARE........................................................................................................................8
1. FILTER.............................................................................................................................8
a. LCD EVENT MONITOR .................................................................................................8
I. NORMAL OPERATION...............................................................................................8
II.WIRING FAULT ......................................................................................................10
III.ABNORMAL VOLTAGE.............................................................................................10
b. CLEARING MEMORY....................................................................................................11
I. BUTTONS .............................................................................................................11
II. DIAGNOSTIC SOFTWARE .......................................................................................11
2. DATA INTERFACE CABLE .................................................................................................12
a. OVERVIEW.................................................................................................................12
b. INSTRUCTIONS FOR DATA RETRIEVAL..........................................................................12
c. INSTRUCTIONS FOR EV-230XX DATA RETRIVIAL..........................................................12
IV. SOFTWARE INSTALLATION ...........................................................................................13
1. COMPUTER REQUIREMENTS ............................................................................................13
2. HARDWARE REQUIREMENTS.............................................................................................13
3. DOWNLOAD AND INSTALL SOFTWARE ...............................................................................13
4. ANDROID APP DOWNLOAD...............................................................................................13
4. INSTALL DATA INTERFACE CABLE .....................................................................................14

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 3
V. USING THE SOFTWARE...................................................................................................14
1. PHYSICAL CONNECTIONS ................................................................................................14
2. START THE SOFTWARE....................................................................................................14
3. CONFIGURE THE DATA INTERFACE CABLE AND COM PORT................................................15
4. SOFTWARE MODES .........................................................................................................17
a. MULTIMETER MODE....................................................................................................18
b. SCOPE MODE.............................................................................................................19
c. CHART MODE.............................................................................................................21
d. OUTLET CONTROL MODE............................................................................................22
e. HISTORICAL DATA MODE ............................................................................................23
f. SETTINGS MODE.........................................................................................................28
g. COMPORT SETUP MODE...........................................................................................30
5. COMMAND LINE OPERATION ............................................................................................30
VI. TROUBLESHOOTING.......................................................................................................31
1. ENVISION PCS FILTER ....................................................................................................31
2. SOFTWARE.....................................................................................................................31
VII. SPECIFICATIONS.............................................................................................................32

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 4
I. PRODUCT OVERVIEW
The enVision PCS is a state-of-the-art, microprocessor-controlled, power filter engineered
with real-time data acquisition and storage.
1. Models: This manual applies to the following enVision models:
2. Key Features:
•Normal and Common Mode EMI Noise Filter
•3-Stage Normal and Common Mode AC Surge Suppressor
•CAT6 Network Line Surge Suppressor
•Modem/Fax Line Surge Suppressor (Note: Not available for EV-230xx)
•Inrush Current Elimination with Zero-Voltage Turn-On and Zero- Current Turn-Off (ICE Zero)
•Wiring Fault Detection
•Catastrophic Over/Under Voltage Shutdown (COUVS®) with selectable thresholds
•Under-Voltage Event Recorder (up to 65535 events)
•Over-Voltage Event Recorder (up to 65535 events)
•Power Outage Event Recorder (up to 65535 events)
•Surge Event Recorder (up to 65535 events)
oRecords surges in all three modes: Line-Neutral, Line-Ground, Neutral-Ground (120V)
oRecords surges in all three modes: Line1-Line 2, Line1-Ground, Line2-Ground
(208-240V)
•Event Timestamp Recorder (up to 512 events)
oRecords actual date and time of events
•Internal logging of measured parameters
oAverage power, maximum power, average voltage, maximum voltage, minimum voltage,
maximum current of 30 minute intervals for up to 138 days
oLine voltage, current, power, NG voltage, frequency, power factor, crest factor, energy
sampled every 10 seconds for up to 2.25 days
•Additional features available when connected to a PC
(detailed in Diagnostic Software User Manual)
3. Technical Support:
•To download software and access further product information, visit www.ametekesp.com
•For enVision PCS technical support, please contact ESP at 1-800-645-9721
Model Number
Voltage (AC RMS)
Current (AC Amps)
Outlet
EV-12010 BR
120
10
EV-12015
120
15
EV-12016 BR
120
16
EV-12020
120
20
EV-20815
208-240
15
EV-20816 BR
208-240
16
EV-20820
208-240
20
EV-20830-630
208-240
30
EV-20830-L630
EV-20830-L630-GNS
208-240
30
EV-23010
230
10
EV-23016
230
16
EV-23016-F
230
16
EV-23030-GNS
230
30

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 5
II. INSTALLATION INSTRUCTIONS
1. Filter Installation:
a. Turn off the machine you are connecting to the
Filter, and unplug the machine’s power cord
from wall outlet.
Éteignez la machine que vous connectez au
filtre et débranchez de la prise murale le cordon
d'alimentation de la machine.
Apague la máquina que intenta conectar al filtro
y desconecte el cable de alimentación de la
máquina del tomacorriente.
b. Connect Modem/Fax line: Connect a phone cord from the wall jack to the
“Modem/Fax” modular jack labeled “IN”, and then connect a second phone cord
from the “Modem/Fax” modular jack labeled “OUT” to the machine/equipment to
be protected. The EV-23010 and EV-23016 models do not support a Modem Fax
telco port.
Please Note: The Filter only provides connectivity and protection for a single phone line.
c. Connect “10/100/1000 ETHERNET” network line: Connect a CAT6 network cable
from the wall jack to the “10/100/1000 ETHERNET” modular jack labeled “IN”, and
connect a second CAT6 network cable from the “10/100/1000 ETHERNET”
modular jack labeled “OUT” to the equipment to be protected.
One CAT6 network cable is included with the Filter.
EV-23010
EV-23016
EV-12015/20
EV-20815/20

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 6
d. Connect Equipment
i. Make sure that the total amperage of all equipment plugged into the Filter
does not exceed the maximum branch circuit rating.
Assurez-vous que l'intensité totale de tous les appareils reliés au filtre ne
dépasse pas la tension maximale du circuit de dérivation.
Asegúrese de que el amperaje total del equipo conectado al filtro no
supere la clasificación máxima del circuito de derivación.
ii. Connect the AC power cords of the equipment to be protected into the
short output power cord of the Filter or two convenience receptacles next
to the short output power cord.
Please Note: Exceeding the branch circuit rating will cause the branch circuit breaker
to trip.
EV-20830-L630
EV-23016
EV-12015/20
EV-23010
EV-20815/20
EV-20830-630

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 7
e. Connect Filter to Outlet: Plug the Filter input power cord into a properly grounded
and compatible branch circuit outlet. The plug is used as the disconnect device.
Please Note: Do not plug the Filter into a re-locatable power tap.
i. If the branch circuit outlet is correctly wired and the magnitude of the line
voltage is acceptable (between 105 and 140 VRMS for 120V products, or
between 190 and 260VRMS for 208-240V products), power will be
connected to the outlets of the Filter and the Green “System On” LED will
illuminate. Your equipment is now protected and installed correctly. You
may now turn all connected equipment back on.
ii. If the branch circuit outlet is incorrectly wired, the Red ‘Wiring Fault” LED
will illuminate and the LCD will display specific wiring fault information. If
this occurs, contact a licensed electrician to correct the outlet wiring. Refer
to Section III: Hardware/EnVision PCS Filter, for LCD EVENT MONITOR
display details.
iii. If neither “System On”, nor the “Wiring Fault” LED illuminates, there is
either no voltage at the receptacle or the magnitude of the line voltage is
not acceptable (less than 105 VRMS or above 140 VRMS for 120V products,
or less than 190 VRMS or above 260 VRMS for 208-240V products). If the
magnitude of the line voltage is not acceptable, specific information will be
displayed on the LCD. If this occurs, contact a licensed electrician to
trouble-shoot the abnormal voltage condition. Refer to Section III:
Hardware/EnVision PCS Filter, for LCD EVENT MONITOR display details.
1. You may also need to verify that the Filter is operating properly.
To test, plug the Filter into a known properly functioning outlet. If the “System
On” LED still does not illuminate in the functioning outlet, contact ESP at 1-800-
645-9721.
•Protection against short-circuits and earth
faults shall be provided as part of the building
installation.
•The socket-outlet shall be installed near the
equipment and shall be easily accessible.
•A dedicated Earth Ground (PE) wire is
required in addition to line voltage.

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 8
III. HARDWARE
1. Filter
a. LCD Event Monitor
The LCD EVENT MONITOR displays useful
information related to data collection, device
status, and troubleshooting.
i. Normal Operation
1. When the EnVision PCS Filter is plugged into a branch circuit
outlet with correct wiring and acceptable line voltage, the LCD
Event Monitor will display the following information:
Menu
Item
Example Display
Electrical
Parameters
(EP)
Line Voltage
Neutral-Ground Voltage
Load Current Draw
Load Power Draw
Load Energy Usage
Crest Factor
Power Factor
Line Frequency

User Manual
© 2019 AMETEK Electronic Systems Protection / Technical Support: 1-800-645-9721 / ametekesp.com 9
Power
Disturbances
(Pd)
Power Outages
Under Voltages (Off)
Under Voltages
(Record)
Over Voltages (Record)
Over Voltages (Off)
Surges
Overload
Last Recorded Event
Outlet State (OS)
On / Off
User Control
(UC)
Press and hold
Menu and Scroll
buttons to
perform control
action.
Turn Outlets On / Off
Memory All Clear (ALC)
Disturbance History
Clear (dhC)
Power Usage Clear
(PUC)
Disturbance Count
Clear (dcC)
Energy Display Clear
(EdC)
Chart Data Start (cdS)