ESP MAGPRO-2i2O User manual

General Description
MAGPRO-2i2O is an addressable input-output module. The module monitors 2 analogue input signals and
controls 2 relay outputs.
MAGPRO-2i2O is powered on from the fire panel and can be controlled via the communication protocol.
The module is mounted is a separate small plastic box suitable for wall mounting.
Installation
Attention: Power off the loop circuit before installing the MAGPRO-2i2O addressable module!
1.󱆱Choose the proper place for installation of the module. Undo the screws of the cover and open the box.
2. Set the module address using MAGPRO-PROG programming tool. The address must be in the range from
1 to 250. The set address is one for the entire module.
3. Dismount the module’s PCB from the box bottom. Mark the mounting holes on the installation surface. Drill
holes at the appropriate box side and run the cables to the module’s loop and input-output terminals.
4. Mount the box bottom at the place of installation. Mount the PCB back on place.
5. Connect the cables to the loop and input-output terminals of the module according the shown Connection
diagrams.
6. Close the cover of the plastic box and fix it to the bottom with the supplied screws.
7. Test the module for proper operation and LED indication.
Installation Instructions
The MAGPRO-2i2O addressable module must be connected only to fire panels from MAGPRO Series!
!
Operating voltage . . . . . . . . . . . . . . . . . . . . . 15÷32 VDC
Consumption stand-by mode . . . . . . . . . . . . 235µА@27VDC
Nom. current consumption . . . . . . . . . . . . . . 260µА@27VDC
Outputs, electrical characteristics (max.) . . . DC 30V/1A; AC 125V/0.5A
Current consumption with 1 LED on . . . . . . . 3.5mA
Current consumption with 2 LEDs on . . . . . . 7mA
2 2
Installation wires . . . . . . . . . . . . . . . . . . . . . . 0.4mm ÷ 2.0mm
Relative humidity . . . . . . . . . . . . . . . . . . . . . . ≤93% @ +40°C
Material (plastic) . . . . . . . . . . . . . . . . . . . . . . PS
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gray
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN54-18
TECHNICAL SPECIFICATIONS
Distributor: Elite Security Products Ltd, Unit 7 Target Park, Shawbank Road Lakeside, Redditch B98 8YN, UK http://www.espuk.com
Manufacturer: Teletek Electronics JSC, 14 Srebarna Str., 1407 Sofia, Bulgaria, http://www.teletek-electronics.com
18020170; RevD; 03/2017
MAGPRO-2i2O
EN54-18
Dimensions
!
IP40
-10°C ÷ +60°C
Installation
!
~320g
Indoor use
Outdoor use
1293-CPD-0258
176mm
126mm 57mm
ATTENTION

Input 1 Input 2 Output 1 Output 2
56k
56k
56k
56k
NO
Common
NC
NO
Common
NC
Loop IN Loop OUT Isolator
Loop
Line + Line - Line + Line -
Loop
Isolator
ATTENTION: When you use the integrated short circuit isolation module connect one
of the “+Loop” loop lead to the “Isolator” terminal of the module.
LED
(red-yellow)
123Mounting and Cable holes
5
Address programming
Connection diagrams
Line + > Line - > Izolator > Line + > Line - >
Down
Right
Up
Modify
Esc
Enter
MAGPRO-
PROG
- Use the cable with
5-pin terminal.
Open the box
Mounting
holes
Possible places for
drilling of cable holes
4Installation
Fix the
box on the
installation
surface
Run the
cables
!LED Indication
2. INPUTS
IN 1
Normal
Normal
ON
Status
IN 2
ON
ON
ON
Normal
Normal
Red
LED
1. OUTPUTS
OUT 1
OFF
ON
Status
OUT 2
ON
ON
ON
Red
LED
OFF
OFF
OFF
SHORT
ON
NORMAL
OPEN
Short circuit
Activation
Stand-by mode
Open circuit
>54µA
38µA - 54µA
23µA - 38µA
<23µA
<13k
13k - 36k
36k - 90k
>90k
* R - resistance between the input and GND
** I - current at the input
Status Description R* I**
IN 1
Normal/ON
Short/Open
Status
IN 2
Normal/ON
Yellow
LED
Normal/ON
Short/Open
Normal/ON
Short/Open
Short/Open
Legend:
- LED Lights on;- LED Lights off
!INPUTS Status