Espressotoria Barista 2.0 User manual

_____________________________Espressotoria
®
System
Automatic coffee capsule m
ac hine
Instruction manual
Espressotoria Barista™2.0

IMPORTANT SAFEGUARDS
When using electrical appliances, in order to reduce the risk of fire,
electric shock and/or injury, these basic safety precautions should
always be followed:
Read all instructions.
Do not touch hot surfaces. Use handles or knobs.
To protect against electrical shock, fire and injury to persons, do not
immerse cord, plug or any part of the coffee machine in water or other
liquid.
Close supervision is necessary when it is used by or near children.
Unplug unit from outlet when not in use and before cleaning, allow to
cool before putting on or taking off parts and before cleaning the
appliance.
Do not operate any appliance with a damaged cord or plug, after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination,
repair or adjustment.
The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
Do not use outdoors.
Do not let the cord hang over edge of table or counter, or touch hot
surfaces
Do not place on or near a hot gas or electric burner, or in a heated
oven.
Always attach plug to appliance first, then plug cord into the wall
outlet. To disconnect turn off the switch then remove the plug from the
outlet.
Do not use the appliance for other than its intended use.
Make sure that your outlet voltages correspond to the voltage stated
on the rating label of the coffee machine.
Do not use the coffee machine with a damaged outlet.
Any examination, repair, or adjustment for the appliance should be
made by the authorized service agent.
If the power cord is damaged, it must be replaced by the manufacturer
or its service agent or similar qualified person in order to avoid danger.
Save this instruction manual for future use.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the
appliance.

This appliance is intended to be used in household and similar
applications only. Other than this application is not recommended,
such as commercial use in restaurant and bar etc. This appliance is
household use ONLY.
Do not open the handle when the appliance is working. Scalding may
occur if the handle is opened during the brewing cycles.
SAVE THESE INSTRUCTIONS
Vittoria Food & Beverage Corporation is not responsible for any damages
to the appliance, caused by:
Heat chamber-water scale build up
Use of inappropriate anti-calcium detergents
Use of inappropriate cleaning detergents
The use not according to the instruction manual
The warranty shall not apply if:
The model and/or serial number on the product has been altered,
removed or is unreadable.
Repairs, modifications or adjustments are made by any other than
authorized dealers.
The product is being used for commercial purposes or other than
approved.
The defect is caused by abuse, misuse or by local conditions
installation/usage not in accordance with the recommendations for
the operation of the product.
The damage is caused by accidents as lightning, flickering, fall, voltage,
flooding, fire, natural disasters or accidents.
The damage is caused by animals.
The product malfunctioning due to normal wear of parts/components.
The product doesn’t work properly because it was not originally
developed/engineered/ manufactured, approved and/or authorized
for the country/area where it is being used.
If it has been purchased in another country.
Normal cleaning not according to instruction, in term of frequency and
method. Cleaning of parts not in the appropriate method.
No performance due to inappropriate use of the appliance.

NOTE:
A short power-supply cord (or detachable power-supply cord) is to
be provided to reduce risks resulting from becoming entangled in or
tripping over a longer cord.
Longer detachable power-supply cords or extension cords are
available and may be used if care is exercised in their use.
If a long detachable power-supply cord or extension cord is used:
1. The marked electrical rating of the detachable power-supply cord
or extension cord should be at least as great as the electrical
rating of the appliance;
2. If the appliance is of the grounded type, the extension cord
should be a grounding type 3-wire cord; and
3. The longer cord should be arranged so that it will not drape over
the counter top or table top where it can be pulled on by
children or tripped over.

Safety instructions
Pl e as e t a ke t i me t o re ad t h e s e saf ety p rec au t ions c a re full y b e fo re c onn ect in g y ou r m a c hin e t o t h e po wer
supply. It is essential to follow them and the operating instructions
 First read this entire operation manual.

To avoid damage, only use capsules designed for this
system with this machine.

Danger of electric shock! Never immerse the appliance
in water or any other liquid.

Connect only to properly grounded power point (120V~)
protected by:
a) At least a 10A fuse when collect only the coffee
machine; OR
b) At least a 15A fuse when collect the coffee
machine together with the ESPRESSOTORIA®
MILK FROTHER.
To make sure that the appliance is switched off, switch
the power point off and remove the plug from the
power point.

Never clamp or run the power cable over sharp corners
of edges.

Danger of electric shock! Damaged power cables may
only be replaced at the customer service centre.
Danger of electric shock! Never touch the power
plug/socket/cable or the appliance with damp or wet
hands.
Danger of electric shock! Never unplug by pulling the
power cable out of the power point or machine, always
turn off the machine and power point before removing
the power plug.
If you need an extension cable, make sure it is suitable
for your appliance (3-pole grounded, 1.5mm2
conductor cross-section), and lay the cable to avoid
tripping.
We recommend connecting the appliance via. An Fl
circuit-breaker. Consult an electrician or other
electrical specialist if in doubt.

Danger of scalding! Never move the appliance during
operation!

Never operate the appliance without water.

Danger of burning! Never touch very hot parts of the
appliance (e.g. brew unit during operations).

Danger of scalding! Do not touch the water jets.
Danger of scalding! Do not move the operating lever
when the appliance is still under pressure making
coffee.
Choose a dry, stable and level support surface for the
appliance, not immediately underneath the power
point, and at least 60cm away from the washbasin and
taps.

Never place the appliance on flammable/fusible
surfaces or equipment.

Never place the appliance or power cable on or nearer
than 50cm to hot surfaces or open flames.

The appliance with power outlet (max. 4.5A 120V~) on
the right housing of coffee machine, it is only for collect
with the ESPRESSOTORIA® MILK FROTHER for making hot
milk or milk froth.
 Always put on the protection cover when the appliance
outlet is not in use.
To avoid any electric shock, never insert any other
appliances other than the ESPRESSOTORIA® MILK
FROTHER.

Never cover the appliance during operation.

Keep children away from the appliance during operation.

Only use the appliance in dry rooms

Danger of tripping! Do not let the power cable hang down.

Pull out the power plug and allow the appliance to cool
down completely before cleaning and or maintenance.
 To prevent frost damage, do not store the appliance at
temperatures below 5°C / 41
o
F (e.g. in caravans)

To prevent damage, never use replacement parts or
accessories not recommended by the manufacturer.
This appliance can be used by children aged from 8 years and
above if they have been given supervision or instruction
concerning use of the appliance in a safe way and user
maintenance shall not be made by children unless they are
older than 8 and supervised. Keep the appliance and its
cord
out of reach of children aged less than 8 years.
Appliances can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the
appliance.

Children should be supervised to ensure that they do not
play with the appliance.
This appliance is intended to be used in household�

DO not use the appliance in case of:
- Faulty operation.
-
Damaged power cable.
-
After failing or other damage.

In such case the appliance must be checked and repaired by
an authorized customer service centre in other to avoid
hazard.

Always pull out the power plug, in accordance with these
safety instructions, before:
-
Relocating the appliance.
-
Cleaning or maintenance.
-
Long periods of disuse.
Clean the water tank, drip try, perforated cover and capsule
container with tepid water and household detergent. Never
clean them in the dishwasher!
 Danger of scalding! The heating element surface is subject
to residual heat after use.

Always disconnect the appliance from the supply if it is left
unattended and before assembling, disassembling or
cleaning.

Switch off the appliance and disconnect from supply before
changing accessories or approaching parts that move in use.
Intended utilization
The Espressotoria BaristaTM 2.0 automatic capsule
machine is designed only to
make espresso, lungo,
hot water and Americano
coffee

Before use
Congratulations! Before using your new machine, please read this
This Espressotoria Barista™ 2.0 automatic espresso
and americano capsule machine is a first-class
product, manufactured with the greatest care. If you
look after it properly it will reward you with many years
of good service.
operating manual carefully, keep it safe and pass it on
to the next user. For further information please
contact the service and sales centre.
After unpacking, please check that the following parts are included:
Caution Note
Check that your power supply voltage is the ·There can be remaining water in the machine
same as marked on the machine rating plate and water tank from the function testing
(120~ 60Hz). before leaving the factory.
Destroy all the plastic bags to prevent danger ·Coffee capsules are not included!
to children!
1. Before using for the first time
Thoroughly rinse out the water tank with hot water
before using for the first time. Clean the capsule coffee
machine using a damp cloth only.
Caution
Danger of tripping! Do not let the power cable
hang down.
Danger of electric shock! Never clamp or run
the power cable over sharp corners or edges or
hot surfaces.
To make sure that the machine is switched off,
remove the plug from the power point.
Danger of scalding: beware of hot water.
Do not operate the machine with an empty
water tank.
Always pull out the power plug before cleaning
the machine.
2. Installation / Power connection
The machine location must meet the following
requirements:
Place the machine on a dry, stable and level
surface, not directly under the power point.
Only use the machine in a dry room.
Never place the machine or power cable on or
nearer than 50cm / 20 inch to hot surfaces or
open flames.
Never place the machine nearer than 60cm / 24
inch to the wash basin.
If you need an extension cable, make sure it is
suitable for your machine (3-pole grounded,
1.5mm² conductor cross-sections).
Remove the protective foil from the perforated
drip tray cover and insert it in the drip tray.
Note
Before using for the first time the internal piping must
be flushed out (for details see: 9. Flushing machine and
internal piping).

Overview
1. Water tank lid
2. Water tank
3. Power switch
4. Operating lever
to load the capsules
5. Dispensing button
small cup, coffee(Espresso)
6. Dispensing button
large cup, coffee(Lungo)
7. Dispensing button
for hot water only
8. Dispensing button
for coffee + hot water (Americano)
9. Dispensing head
for coffee and hot water
10. Upper drip tray cover
11. Drip tray
12. Lower drip tray cover
13. Capsule tray
for used capsules
14. Capsule full indicator
15. Appliance outlet for milk frother base
16. Protective cover

Starting up
3. Filling the water tank 4. Starting up / Preheating
Note
‧Never use distilled water.
‧Use only cold tap water.
‧After filling the water tank, and before the next time
that coffee is dispensed, press one of the dispensing
buttons, until you obtain a regular flow of water from
the dispenser (without the capsule).
‧Water which has been softened with
commercially available water filter can be used.
Damages caused by wrong handling of the water filter
are not covered by the guarantee.
‧If the water tank is empty and the pump sounds very
loud, this does not indicate any malfunctioning. Press
one of the dispensing buttons lit up and the pump is
immediately deactivated.
‧If no dispensing button is pressed, the pump is
automatically deactivated after 20 seconds.
‧How does the water level sensor work?
When there is insufficient water in water tank (below
the min. water level), all dispensing buttons will flash
blue alternately in a counterclockwise direction. After
filling the water tank, all dispensing buttons light up in
blue. The machine goes back to normal.
Filling without removing the
tank
‧Turn off the machine.
‧Remove the water tank lid.
‧Fill the tank up to the MAX
mark with cold water (the
maximum is 1 liter / 1 qt).
‧Replace the lid.
Filling by removing the water
tank
‧Switch off the machine.
‧Remove the water tank lid.
‧Lift up the water tank holding
it by the special grip (on the
outside) and remove it pulling
upwards.
‧Fill the tank up to the MAX
mark with cold water (the
maximum is 1 liter / 1 qt).
‧Lower the water tank into
place, pushing firmly.
‧Replace the lid.
Connecting the appliance
‧Connect the machine to a
grounded power point by
plugging in the power plug.
Switching on
Before turning on the power
switch, make sure that:
‧the operating lever is
closed.
‧the water tank is full.
‧the water tank is firmly in
place.
‧the drip tray with the
container is completely
inserted.
‧Turn on the machine with the
main power switch.
Preheating
After switching on the
machine the two dispensing
buttons &flash blue
to indicate heating up.
When heating up is finished
(after approx. 1 min.), all
the four buttons remain
illuminated. The machine is
now ready to use.
Note
Before using for the first time and after long periods of
inactivity (like vacation, e.g.) the internal piping must
be flushed out (for details see: 9. Flushing machine
and internal piping).

Making coffee
5. Making Espresso, Americano & dispensing hot water
Note
For safety reasons the dispensing button may be pressed
only if the operating lever is closed.
6. After making coffee
Making coffee with this machine is
only possible with capsules
designed for this system. Use one
capsule per cup.
Use button or to make
coffee, follow the steps in this
order:
‧Be sure there is enough water in
the tank before making coffee.
‧Move the operating lever back
completely.
‧Insert a capsule in the capsule
opening. It automatically falls into
the right position.
‧Move the operating lever
completely forward to load the
capsule into the brewing position.
‧Place an empty cup under the
dispenser.
‧Press the dispensing buttons:
Small cup: 30ml / 1 fl. oz
coffee flow
Large cup: 100ml / 3.3 fl. oz
coffee flow
Use button to make hot water:
Be sure there is enough water in
the tank. Press and then release
button . It starts to have hot
water flow after heating up.
Hot water:100ml / 3.3 fl. Oz
water flow
Use button to make an
Americano:
Press and then release button .
After waiting for around 8 seconds
for heat
up, it starts to have hot water. You
have to insert a capsule in the
capsule opening before the water
flow finishes. Shortly after finishing
water flow, it will brew coffee and
automatically stop after finish.
Hot water +coffee:
120ml / 4 fl. oz hot water
flow + 30ml / 1 fl. oz
coffee flow
After making coffee the empty
capsule is ejected as follows:
‧Move the operating
lever completely back to eject
the empty capsule into the
container. The container holds
up to 16 used capsules. It must
be emptied regularly.
‧If the used capsules held
reaches the max. capacity of
the container, the capsule full
indicator will flash red when
you move the operating lever
back. This reminds you to
empty the container.
‧If you want another
cup of coffee, just insert a new
capsule and press the coffee
dispensing button (see 5.
Making coffee).
The automatic switch-off device is programmable (8.
Programming the amount of water). The dispensing
process stops automatically when the programmed
amount of coffee has been reached. To interrupt the
process at any time, press the button again.

Energy saving mode /
Programming the amount of water
7. Energy saving mode
Switch to long ready mode
8. Programming the amount of water & coffee
Note
‧The capsule may stick in the opening if it has been
there for a long time. If so, open and close the
operating lever. If the capsule is still blocked, push
down lightly with a finger.
‧Various kinds of coffee (including decaffeinated)
capsules are available.
‧For Hygiene reasons, we recommend filling the
water tank with fresh water, emptying the capsule
container and drip tray every day.
Tips
‧Use thick, pre-heated cups for espressos in order to
prevent cooling down too quickly. Cups can be pre-
heated by rinsing them with hot water.
Caution
To avoid damaging your machine, never use other
makes of capsule.
If the machine is not being
used, after 5 minutes the
energy saving mode is
activated, the voltage
absorbed by the machine
falls to ≤0.5 Watt. The
energy saving mode is
indicated by the dispensing
button lighting up in
green.
To use the machine press one
of the dispensing buttons.
The machine is ready to
dispense coffee as soon as
the buttons are steadily lit up
in blue.
If the machine is not used for
an extended period of time
(for example during holidays),
switch off the machine,
empty the water tank and
pull the power plug out of
the power source.
Switch off the machine
and close the metal
handle.
Switch on the machine
while pressing the
button . Keep the
button pressed until it
glows blue. The
machine will now stay
in Ready Mode for
max. 4 hours.
To return to the normal
energy saving mode
please switch on the
machine while pressing
the button . Keep it
pressed until it glows
blue.
With the ESPRESSOTORIA
®
Barista™ 2.0 Automatic
capsule machine you can
program the amount of
water for these 4 dispensing
buttons:
For button or
‧Hold down the button to
be programmed (for
example for button )
until it starts to flash blue
rapidly (around 3 seconds).
The dispensing cycle
commences.
‧Once the desired amount
in the cup has been
obtained, press the button
again. The dispensing
process stops, the amount of
water is programmed and
four buttons light up.

Programmable quantity
For button & :
small cup (min.30ml / 1 fl. oz to max.220ml / 7.4 fl. oz)
large cup (min. 30ml / 1 fl. oz to max.220ml / 7.4 fl. oz)
For button :
hot water amount
(min.30ml / 1 fl. oz to max.220ml / 7.4 fl. oz)
For button :
hot water amount
(min.30ml / 1 fl. oz to max.220ml / 7.4 fl. oz)
coffee flow amount
(min.30ml / 1fl. oz to max.160ml / 5.4 fl. oz)
For button
‧Hold down the button
until it starts to flash
blue rapidly (around 3
seconds). The dispensing
cycle commences. It
starts to jet water after
heat up.
‧Once the desired
amount in the cup has
been obtained, press the
button again. The
dispensing process stops,
the amount of water is
programmed and four
buttons light up.
For button
‧Hold down the button
until it starts to flash
blue rapidly (around 3
seconds). The dispensing
cycle commences. It starts
to have hot water after
heat up.
‧You need insert a
capsule in the capsule
opening during the water
flow process.
‧Once the desired
amount of hot water in
the cup has been
obtained, press the
button again.
‧Programming of coffee
flow amount will start
shortly after finishing hot
water amount
programming.
‧Once the desired
amount of coffee flow in
the cup has been
obtained, press the
button again. The
dispensing process stops,
the amount of coffee flow
is programmed and four
buttons light up.
How to reset to factory
default settings:
To return to the default
settings, press both buttons
& simultaneously for
3 seconds until they both
glow blue then release, The
machine is now reset to the
factory default settings.
The default quantities are:
Small cup: 30ml /
1 fl. oz coffee flow
Large cup: 100ml /
3.4 fl. oz coffee flow
Hot water: 100ml /
3.4 fl. oz water flow
Hot water + coffee:
120ml / 4 fl. oz hot
water flow + 30ml /
1 fl. oz coffee flow

Maintenance
9. Flushing out the machine and internal piping
10. Emptying capsule container and drip tray
Cleaning / Storage / Final disposal
11. Cleaning the appliance
Before using for first time, or
after long pauses (for example
holidays), the machine must be
flushed out. This short
procedure thoroughly flushes
out and cleans the internal
piping.
‧Turn on the machine with the
main power switch.
‧Press one of the lighted
dispensing buttons (the pump
begins working and the water
circulates).
‧After dispensing the
programmed amount of
water，the pump is
automatically deactivated. The
procedure can be interrupted
or repeated at any time by
again pressing the chosen
button.
Caution
‧The water coming out of the dispenser head is hot!
Danger of scalding!
The capsule container
holds around 16 empty
capsules and the upper
drip tray around 150 ml /
5.1 fl. oz of residual water.
For hygiene reasons we
recommend emptying the
capsule container and the
drip tray every day.
‧
Hold the drip
tray firmly and pull it out by
lifting gently.
‧Remove the perforated drip
tray cover.
‧Pull the capsule container out
of the drip tray.
‧After emptying/cleaning,
reassemble the pieces in
reverse order and insert
them into the machine as far
as they go.
Drip tray and cover, capsule
container
‧Clean the drip tray, perforated
cover and capsule container
with tepid water and
household detergent.
‧Never clean them in the
dishwasher!
Coffee machine
Always pull out the power
plug before cleaning the
machine.
Never immerse the
machine in water or clean
it under running water.

(For Decalcification process, details see 13. Descale)
Fill the water tank with
1 liter water
‧Clean the machine with a
damp cloth and allow to
dry afterwards.
‧Never use abrasive cleaning
agents or materials.
Water tank
‧Clean the water tank with tepid
water and household detergent.
‧Never clean it in the dishwasher!
This appliance has two self-
cleaning modes:
Cleaning mode with COLD water
Press dispensing buttons &
for 9 Seconds, until button
flashes green, then release them.
The full cleaning cycle mode starts
and will automatically stop after
3.5 minutes. The full cleaning
process is completed.
CAUTION
The water coming out of
the dispensing head is
HOT! danger of scalding !
Fill the water tank with
1 liter / 1 qt water
Cleaning mode
dispensers with HOT
water.
Press dispensing buttons
&
for 3 Seconds, then both
buttons glow blue, and
release them until button
glows blue. Then
button will flash blue.
The full cleaning cycle
mode starts and will
automatically stop after
3.5 minutes. The full
cleaning process is
completed.

12. Storage / Final disposal
‧Important : If the machine is not used for a long
time, flush out the piping by pressing
button before storage.
Correct Disposal of this product
Descale
13. Descale
Regularly descale the machine is
highly recommended to prevent
limestone block the piping which
might damage the machine. If you
find drips water continuously or
sprays irregularly out of Dispensing
heads, you need to decalcify the
machine. Follow the below
instructions and procedure to run
the decalcification process.
‧If the machine will not be
used for some time, switch
it off and pull out
the power plug.
‧Store your coffee machine
in a dry, dust-free place out
of reach of children.
‧To avoid frost damage, do
not store the machine at
temperatures below 5 °C /
41 oF(such as caravans).
Tap water varies according to region. The limestone
particles in hard drinking water are deposited as residues
in the machine and can block the piping and cause
damage. To prevent this, be sure to decalcify the machine
at the very least after making 100 cups of coffee or in any
case if the output falls significantly or, in any case after
max. one month.
Decalcification of machine must be done correctly to
prevent damage. So it is essential to follow these
instructions.
This marking indicates that
this product should not be
disposed with other
household wastes
throughout the EU. To
prevent possible harm to the
environment or human
health from uncontrolled
waste
disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return
your used device, please use the return and
collection systems or contact the retailer where the
product was purchased. They can take this product
for environmental safe recycling.

Note: Always read carefully and follow the
instructions or recommendations on the packaging of the
descaling agent to be used.
Caution - These liquids are scalding hot!
Danger of scalding!
Caution
‧Never clean the machine with vinegar. This cause
damage to the appliance and will make your coffee
taste bad!
‧Damage caused by incorrect decalcification or
failure to decalcify is not covered by the guarantee.
‧These liquids are scalding hot! Danger of scalding!
‧Follow carefully the safety instructions inside the
descale liquid packaging.
1. Recommendations: purchase commercially available
descaler (decalcifying liquid), and
dilute according to the manufacturer‘s instructions; pour
the mixture into the water tank.
2. Make sure the capsule container is empty.
3. Place a large bowl under the dispensing head to
collect the decalcification liquid and limestone
residues.
4. Turn on the power switch (the coffee dispensing buttons
start flash).
5. As soon as the dispensing displays remain on, press the
dispensing buttons &to have 3.5-minutes cleaning
mode with hot water or 3.5-minutes cleaning mode with
cold water. (see 11. Cleaning the appliance)
Wait until the dispensing operation is complete.
6. Turn off the machine with the power switch for about five
minutes and let the decalcifying fluid take effect.
7. Turn on the power switch again.
8. Repeat the process until the tank is empty.
9. Rinse the water tank well and refill with water. Place the
tank back inside the machine.
10. Press the coffee dispensing button. Press the button
again until the water tank is empty.

Troubleshooting
Problems and their remedies
Repairs to your machine may only be carried out at an authorised service centre. Unprofessional repairs and use of non-original
replacement parts can be dangerous for the user. In case of unprofessional repairs, no liability will be accepted for resultant
damage and the guarantee is invalidated.
If this troubleshooting guide does not help you solve your problem, please contact your Espressotoria® System Customer
service on 1800 610 5512.
IMPORTANT: pull out the power plug immediately in case of malfunction or possible damage to the machine after a fall.
Problem Possible cause Remedy
No coffee output or insufficient
output
water tank empty fill the water tank
defective pump
contact the service centre
capsule not (completely) perforated use a new capsule/contact the service
centre
operating lever open close lever completely
piping blocked with limestone deposits
decalcify the machine
No coffee or water jet output water tank not properly in place insert water tank correctly
defective pump contact the service centre
Cold coffee heating system defective contact the service centre
4 dispensing buttons flash blue
alternately in a counterclockwise
direction
insufficient water in water tank (below the
min. water level)
after filling the water tank, all
dispensing buttons light up in blue. It
goes back to normal.
Water drips continuously or sprays
irregularly out of Dispensing head
machine / piping blocked with limestone
deposits
decalcify the machine
Occasional drops drip
out of dispensing head
empty capsules have remained in the
brewing unit
eject the capsule (occasional drops
are normal, it is not a defect)
Coffee tastes sour
machine not flushed out enough
after decalcifying
flush out the machine again
capsule has passed expiration date use a new capsule
The amount of water
programmed per cup is
not correct
water tank empty fill the water tank
programming changed reprogram
Dispensing button
fast flashes Red
electronic malfunctioning switch off the machine, wait for 20
minutes and restart it. If the problem
persists, contact the service centre
Dispensing button
lights up in Green
no malfunctioning. The machine is in
energy-saving mode
press one of the dispensing buttons

Dispensing button
fast flashes Green
machine is exposed to cold temperature for
prolonged time, the heating function is
disabled for safety reasons
switch off machine, wait until it
reaches room temperature and
restart. If the problem persists,
contact the service center
Dispensing button
fast flashes Purple
electronic malfunctioning
let the machine cool down first, it will
return to normal after approx. 10
mins. If the problem persists, contact
the service center
Capsule tray light
flashes Red
the used capsule tray is full empty the used capsule tray

Simply purchase the ESPRESSOTORIA®SYSTEM
compatible MILK FROTHER, connect with your
Espressotoria Barista™2.0 coffee capsule
machine to make milk-based coffees.
ESPRESSOTORIA®SYSTEM compatible MILK FROTHER

Vittoria Food & Beverage Corp.
3121 S La Cienega Blvd, Los Angeles
CA 90016 United States