Etec E100 User manual

One Shelf Wall Mounting
A/V Component Stand
Installation Guide
Model: E100
For technical assistance or troubleshooting
please call 1-855-994-3832.
This product is intended for use only with Audio/Video components (Not for use with any type of TV). The maximum weight
capacity per shelf is 22 lbs. See apparatus instructions. Using with an apparatus heavier than the maximum shelf support
weight indicated may result in instability and cause personal injury.
READ THIS FIRST
Read this entire manual! Do not attempt to install this product if you do not understand the instructions. Contact a qualified
mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what specific wall
materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or damaged parts.
Improper installation may result in damage to your Components, TV, property, and personal injury.

This product is intended only to be used to support Audio/Video Components (DVD players,
Cable boxes, 5.1 Sound systems, etc.) Do not use this stand for any type of Television.
Use with components heavier than the maximum shelf weight capacity can damage equipment and
cause personal injury.
Schoenfeld International Inc. and ETEC are not responsible for personal injury or product
damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of this
product.
Always wear safety goggles to when drilling or installing hardware.
Tools
For your convenience, we have included an allen wrench and a socket tool with this mount. For the best as-
sembly experience and mounting safety, we always recommend using full-size tools for each assembly steps.
Below is a recommended tool list you will need for proper and safe installation. See applicable warnings
in this manual about certain types of mounting surface materials and the special hardware and tools that
should be used.
•Drill with a specific size drill bit to pre-drill holes in the wall
•Stud finder
•Tape measure
•Pencil
•Screw drivers
•Socket wrenches
•Small hammer
•Safety goggles
CHILD SAFETY
How and where you use your A/V Component Wall Mount Stand is extremely important for Child Safety
As you set up and use your new product, keep all of these safety tips in mind.
One size of A/V Component Stand does not support all components weights and sizes.•
YourA/VComponentStandassemblyinstructionscontainsspecificinformationonthemaximumweight•
capacity per shelf that your A/V Component Stand can safely support. Do not exceed the maximum
support weight for each shelf.
Carefully read all of enclosed instructions for proper use of this product. If you have any doubts about•
safe and secure assembly, please contact a professional.
Don’t let children climb on or play next to Wall Mounted A/V Stands or TV Wall Mounts.•
Remember that children can become excited while watching a program, especially on a “larger than•
life” TV. Make sure to place or install the A/V Component Stand where it cannot be pushed, pulled on,
or knocked down.
Make sure that you safely route all cords and cables so that they cannot be pulled or grabbed by curious•
children.

15
15

Do not attach this A/V Component Stand to any wall with Brick or steel stud construction.
Attaching this mount to wood or concrete walls requires special tools and hardware to
ensure the mount is securely and safely attached to these materials. Brick and concrete
will break or crumble if special concrete drill bits and drill operating speeds are not properly
used. Consult a professional if you areunsure or have any doubts about the safely of the
installation. Personal injury or equipment damage can result if the mount is not properly
installed.
Wood stud walls (Fig 3):
1. Use an electronic stud finder to locate the wall studs. Mark their locations on the wall.
2. Place the Wall Bracket flat against the wall in the desired mounting location, alighning the mounting holes in
the bracket with the studs. Use the Wall Bracket as a template to mark the mounting holes on the wall.
3. Use a 4.5mm drill bit to pre-drill six holes at least 2” (50 mm) deep at the marked locations.
4. Use the supplied Long Bolts (4) with the 5x5mm Hex Wrench (11) to mount the Wall Bracket into the wall.
Do not use wall anchors in wood stud walls.
5. Use a level to make sure the stand Wall Bracket is vertical and securely tighten the bolts.

15

9

10

11
LIMITED SIX-YEAR WALL MOUNT WARRANTY
We warrant this product to you, the original purchaser at the time of purchase printed on a dated store receipt from
an authorized ETEC retailer and for a period of six-years thereafter that our wall mount product and all it’s parts
and components are free of defects in material and workmanship under normal use. This warranty is subject to
the provisions below. ETEC’s sole obligation and the purchaser’s exclusive remedy pursuant to these warranties
are limited to replacement at ETEC’s sole discretion. There are no other warranties except as expressively set
forth below either expressed or implied, including any warranty of merchantability for any particular purpose.
Should you be missing any of the assembly parts or components (screws, pieces, etc.), please contact the
Customer Support Center to secure a replacement. It is not necessary to bring the unit back to the store. When
calling, please reference the parts list found in the Instruction Manual to help us accurately identify the missing
parts and promptly provide replacements.
Our Customer Support Center is available Monday to Saturday (10:00AM to 7:00PM EST) for technical assistance
or troubleshooting. To contact us please call 1-855-994-3832.
This warranty is expressly limited to the replacement of wall mount parts and components described in the parts
list located in the Instruction Manual included with the product.
This warranty applies under conditions of normal use.
This warranty does not cover: any product, which has been subject to damage due to improper assembly or
disassembly, products which were not assembled, installed, used, or maintained in accordance with the product
assembly instructions & warnings, acts of nature, misuse, neglect, accidents, abuse, exposure to elements,
outdoor use, extreme temperature ranges, damage during transit, commercial use, modification of, or to any part
of the product or attachments to the product not approved by ETEC. Also not covered are costs for
assembly/dis-assembly labor, costs incurred in shipping the unit or parts for warranty repair/exchange or any
products purchased from unauthorized ETEC sellers. Under no circumstances shall ETEC, be liable for any loss
(direct, indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage arising out of, or in
connection with, the use of this product. Nor shall ETEC have any responsibility for incidental or consequential
damages resulting from the breach of this warranty including but not limited to inconvenience, purchase or rental
of replacement products, loss of profits or commercial loss.
We reserve the right to request damaged parts or units be shipped to our offices for inspection or confirmation of
any warranty claims.
This warranty does not cover product sold ‘As Is’.
This warranty is valid only to the original purchaser of the Product in the United States and Canada and grants
specific legal rights.

Rev 1.3 September 2013
2013