Eterna B18WSS User manual

Ifyou experience problems:
If your light is defectiveor develops afault,pleasereturn it tothe placewhere you bought it. You can call our Helpline
for advice.TheHelpline willgladlygiveadviceonanyaspectofanyEterna Lighting product butmaynotbe able to
givespecificinstructionsregarding individual installations.
Ifindoubt,consultaqualified electrician.
Helpline:
Tel:[phone]Fax: [phone]Email: [e-mail]
For answers tofrequently asked questions (FAQs)and other information visit our web-site
www.eterna-lighting.co.uk
Lampreplacement:
>Switchoff the electricityatthe mains.
>Removethe diffuser etc., see diagram inside. Takecare not tolosethe small “O”ringseals fitted tothe screws.
>Removeand replacelamp. Note,the lamppullsdirectly outofthe lampholder, do not twist.
>Replacethe diffuser and trim (if fitted ).Ensure thatthat all sealsand gasketsare correctly positioned.
Replacementlamptype:
Wattage:18 W
Supply Voltage:240 V
Type: G24q baseCFL—4pin
Cleaning:
>Disconnect the power and clean the exterior only ofthisfitting withamoist(notwet)cloth.
>The diffuser maybe removed and washed in amild detergentsolution.Makesure itiscompletelydrybefore
putting it backon your lightfitting.
>Donot useanychemical or abrasivecleaners.
Eventually, you may wanttoreplace thislightfitting:
When your lightfitting comestothe end ofit’slifeor you choosetoupdateor upgrade itby
replacing it, pleasedo notdisposeofitwithyour normal household waste,pleaserecycle where
facilitiesexist.When youneed todisposeofthisfitting,checkwithyour retailer or local authority
for suitable options. Newregulationsrequire the recycling ofWastefromElectrical and Electronic
Equipment(European “WEEE Directive”effectiveAugust 2005—UKWEEE Regulationseffective
2nd January 2007 ).
PLEASE READ THESE INSTRUCTIONSBEFOREINSTALLING
YOUR NEWFITTING
--
PLEASE RETAINFORFUTUREREFERENCE
Low energybricklight
Model(s)
B18WSS
Pack contents:
Bricklight fitting c/w trim 1
Cable gland 2
Screws 4
Plastic wall plugs 4
4pin CFL 1

Safetymarkings:
Read thisfirst:
>Thislightfitting mustbeinstalledin
accordance withtheBuilding Regulations.
Thesemaybeobtained fromHMSOorviewed
and downloaded from www.communities.gov.uk
followingthe linkforBuildingRegulations.
>Ifinanydoubt, consultaqualifiedelectrician.
>Disconnectthe fittingfromtheelectricalsupply
before flashor highvoltagetesting.
>Suitablefor indoor and outdoor use.
>Thisproduct issuitableforinstallationon
surfaceswithnormalflammability(indicated by
the "F"inatriangle)e.g. wood, plasterboard,
masonry. Itisnotsuitablefor useon highly
flammablesurfaces(e.g. polystyrene,textiles).
>Before makingfixinghole(s), checkthat there are
no obstructionshidden beneaththe mounting
surfacesuchaspipesorcables.
>Ifthe location ofyour newfittingrequiresthe
provision of anewelectricalsupply,thesupply
mustconformwiththerequirementsofthe
BuildingRegulations.
>Thisproduct isdesigned for permanent
connectiontofixed wiring: thisshouldbe either a
suitablelightingcircuit(protected witha5or 6
AmpMCBorfuse)or afusedspur (witha3
Ampfuse)viaafusedconnection unit. We
recommendthatthesupplyincorporatesaswitch
for easeof operation.
>Makeconnectionstothe electricalsupplyin
accordancewiththe followingcode:
Live-Brownor Red
Neutral-Blue orBlack
(Earth-Green andYellow) Note:this
terminalisprovided forlooping through and
isnotrequired forthe safetyor operation of
the fitting.
>Thisfittingisdoubleinsulated, donotconnect
anyparttoearthother thanthe loopingthrough
terminalasdescribed above.
>You are advised at everystageofyour
installationtodouble-checkanyelectrical
connectionsyou havemade.Afteryou have
completedyour installationthere are electrical
teststhatshouldbecarried out:thesetestsare
specified inthe WiringRegulations(BS7671 )
referred tointhe BuildingRegulations.Ifin
doubt,consultaqualified electrician.
Installation:
1) Choosethe locationforyour bricklight according
totheconditionslisted above.Your bricklight is
designed tofitintothespaceoccupied byone
normalsinglehousebrick.
2) Removethestainlesssteeltrimand diffuser.
Takecare nottoloseanyofthe“O”ringsealson
the screws.
3) Removethelampbypullingstraight out of the
lampholder—do nottwist.
4) Loosen thescrewseither sideofthe lampholder
and removethetwoscrewsattheoppositeend
of the ballastcaseinsidethefittingand slideit
out.
5) Offerthe remainingcaseintothecavityinto
whichyouwant ittofitand markthelocation of
the fixingholesonyourmountingsurface.
6) Makethe fixingholesasappropriate.
7) Removetheblank(s)fromthecableentry(ies)
usingeither acore drillorslowdrillwithlargebit.
the holeshouldbe 16.0mm diameter.
8) Fitthecablegland(s)tothecaseasrequired.
Thread the supplycablethroughthe gland and
intothefitting.
9) Makethe electricalconnectionstothe ballast
accordingtothecolourcode above.
10)Slidethe ballastcasebackintopositionand
replace/tighten allfour screws.
11)Ensure thatthe reflectorsitscorrectlyinthe
case.
12)Tighten the gripring(s)on thecablegland(s).
13)Offerthe caseintothe cavityoncemore and
secure inposition usingthe fixingssupplied.If
the fixingssupplied are notappropriatetoyour
installation,selectsuitablealternatives.
14)Re-fit thelamp,pressfirmlyintothe lampholder
until itclicksintoplace.
15)Fitthe diffuserontothe fittingand secure using
the twoscrewsonthe longestsides(top and
bottom).Ensurethatthesmallrubber “O”ring
gasketsareinplace.
16)Ifyou do not wanttofitthestainlesssteeltrim,
B18WSS Bricklight—low energy 070410PA.pub
IP65
insertthe remainingtwoscrewsand tighten.
17)Ifyou dointendtofitthestainlesssteeltrim,
secure it inplaceusingthetworemaining
screws.
18)Restore the power andswitchon.
B18WSS Bricklight—low energy 070410PA.pub
StainlessSteeltrim Opaldiffuser
Cablegland
Ballastcase
Lampholder
To remove ballastcase
Loosen2screws
Remove2screws