ETS-Lindgren 5225 Series User manual

Model 5225 Series Shielded Enclosure
© Copyright 2008–2010 by ETS-Lindgren L.P. All Rights Reserved. No part of this document
by any means without written permission from ETS-Lindgren L.P.may be copied
The logo is a trademark of ETS-Lindgren L.P.ETS-Lindgren
399296, Rev B
USA Headquarters
1301 Arrow Point Drive
Cedar Park, TX 78613
Phone: [phone]
[email protected]
Please see
f
www.ets-lindgren.com
or a list of all ETS-Lindgren offices.
Safety Information
Warranty Information
For warranty information, see the .Product Information Bulletin
ONLY QUALIFIED PERSONNEL should install, operate, or service this equipment.
CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself
may void your warranty. If you attempt to service the unit by yourself, disconnect all electrical power
before starting. There are voltages at many points in the instrument that could, if contacted, cause
personal injury. Only trained service personnel should perform adjustments and/or service procedures
upon this instrument. Capacitors inside this instrument may still be CHARGED even when instrument is
disconnected from its power source.
WARRAN TY
For complete safety information, see the .Product Information Bulletin
Revision/Date:
B, Adjust graphics, add specifications - October, 2010
A, Initial Release - September, 2008
www.ets-lindgren.com www.ets-lindgren.com
The following views and setup instructions apply to a standard configuration of the
. Components may vary for custom
Model 5225 configurations. Contact ETS-Lindgren for questions regarding your configuration.
ETS-Lindgren Model 5225 Series Shielded Enclosure
IEC power connector Lid handle
(on front)
Front, Right Side
Antenna patch with
SMA connectors
Front, Left Side
Back View
Antenna patch with
SMA connectors
Location for
equipment under test
(EUT)
Inside View
Filtered DB-9
feedthrough
Fiber optic
feedthrough

Model 5225 Series Shielded Enclosure
www.ets-lindgren.com
Before connecting components, read on the back page of this document.Safety Information
Setup Instructions
Raise the lid handle to open the door of the Model 5225.
1.
2. (As required by the testing you want to perform) Attach cables to the SMA connectors
on the antenna patches.
4. Place EUT inside the Model 5225 and connect cables as required.
Lower the lid handle to close the door of the Model 5225.
6.
5. Attach a power cable to the IEC power connector.
3. (As required by the testing you want to perform) Connect cables to the DB-9 and
fiber optic feedthroughs.
Apply power to the Model 5225. Perform testing as required.
7.
Note: ETS-Lindgren may substitute a similar part or new part number with the same functionality
for another part/part number. Contact ETS-Lindgren for questions about part numbers and
ordering parts.
Shielding Specifications
Filter Specifications
Attenuation 100 dB, 5 MHz–6 GHz
Current 10 Amps
Voltage 100—250 VAC
Operating Frequency 0 Hz–60 Hz
Insertion Loss 100 dB, 5 MHz–18 GHz
Electrical Specifications
Weight 22.0 kg (48.6 lb)
Physical Specifications
External Dimensions
Length:
Width:
Height:
71.1 cm (28.0 in)
43.2 cm (17.0 in)
60.9 cm (24.0 in)
Internal Dimensions
(Absorber to Absorber)
Length:
Width:
Height:
60.5 cm (23.8 in)
32.3 cm (12.7 in)
50.3 cm (19.8 in)
Coupling Loss
Typical Coupling Loss Repeatability +/-1dB
Typical Internal RF Absorption 2 GHz–6 GHz
Typical RF Isolation 2 GHz–6 GHz >80 dB
Better than -36 dB from
5 GHz to 6 GHz for
high frequency antennas
•
(~25 dB at 5.5 GHz) using
identical antennas at 10 cm
from antenna surface
•
•30 dB to 35 dB minimum
at the 2.54 band for
low frequency antennas
Connectors •SMA feedthrough (2)
•Fiber optic feedthrough (1)
•Filtered DB-9 feedthrough (1)
•Type N (1)
•IEC power (1)