Eureka Jewel Insert User manual

Operation & Installation Instructions
Jewel Insert
Please keep these instructions for future reference.Rev *
Jewel Insert 16
WARRANTY
1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 warrants the following components of its heaters against defects in workmanship
and/or materials for the following periods from the date of purchase:
a) the rebox for ten years;
b) the paint nish for a period of 12 months if the purchaser has followed the instructions provided by Gason in the operation and Installation Instructions manual; and
c) all other components for 12 months except the glass, re brick lining or ba e plate if, in the opinion of Gason, these items have been damaged by impact.
2. This extended warranty does not apply;
a) if the heater is purchased from a person who has not been authorised by Gason to sell its products; b) if, in the opinion of Gason, the heater or any other component has been subject to abuse, misuse, alteration, modi cation or has not been installed, operated or maintained in
accordance with the instructions provided by Gason; or,
c) to owners other than the original purchaser.
3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason servicce
centre to arrange for an assessment.
4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:
a) replace the heater; b) repair or replace speci c components of the heater; or
c) provide a full refund.
5. Parts replaced under warranty are warranted for the balance of their original warranty period. 6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this
warranty must pay all costs associated with:
a) returning the heater; and b) the delivery or collection of any new or repaired heater.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Any bene ts you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under law in relation to the heater to which
these warranties relate.
These warranties are given by: AF Gason Pty Ltd Blake Street Ararat VIC 3377 Please contact us if you have any queries on: Phone: [phone] or email us via the “Contact Us” section of our website: www.gason.com.au
224438

Jewel Insert 2 Jewel Insert 15
Troubleshooting (Continued)
Read and follow these instructions carefully before installing and
u
sing this appliance.
WARNING
!
WARNING
!
Safety Warnings
• A ue re with resulting damage may occur if the appliance is not installed,
operated and maintained as per this booklet.
• Never place combustible materials such as wood, paper or furniture near the
appliance.
• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood,
flammable liquids or any substance containing salts or corrosives.
• This appliance must not be installed and operated in an area where kerosene,
petrol, paint thinner or other ammable liquid is used or stored.
• The ue system must be inspected and cleaned annually or sooner if required.
Failure to do so could result in an excessive buildup of creosote which may
result in a ue re, which may damage the ue or cause damage to your home.
• The surface of the appliance becomes hot during operation. Do not touch the
surface of this appliance. Keep children away from this appliance during
operation. Do not allow anyone to operate this appliance who is not familiar
with this instruction booklet.
WARNING
!
Paint Curing and Care
Your heater is coated with the best available heat resistant paint. Even though
t
he paint has been baked after application, it may require further temperature
c
uring. It may, if you overre the heater on its rst re, discolour. For your rst
t
wo or three rings, never exceed Medium air setting and always have the fan
o
n when above low burn. Do not wipe the heater while the paint is curing. After
t
he paint has cured the only maintenance required to maintain the heater’s nish
i
s to wipe it with a soft cloth. Do not use any commercial cleaners or solvents on
t
he paint nish.
W
e are proud of the presentation of our products. If at any time you need to
f
reshen up the paint, your local dealer has touchup paint available for purchase.
Y
ou may even change the colour of your heater if you wish.
If you have any enquiries, please contact the dealer from whom you purchased your heater:
P
LEASE COMPLETE:
D
ealer Name:
D
ealer Address:
Phone:
P
lease attach your original purchase dockets to this booklet for future reference.
PAGE INTENTIONALLY BLANK
To aid heater installation, remove door, bae system and cast iron liners to reduce
overall heater weight.
This heater is painted in stovebrite Metallic Black - code 6309.
Dealer Email:

0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%< (&11R '$7(
5(9
%< (&11R '$7(
5(/($6('
'21276&$/(


$

6&$/(
3$571R
,1%$66(0%/<
(85(.$-(:(/-,1'$5$63(&75(
77
(1*35 
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU  
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

 77
Jewel Insert 14 Jewel Insert 3
Installation
WARNING
!
Installation
THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS
MANUAL AND THE FLUE MANUFACTURER’S SPECIFICATIONS.
WE RECOMMEND THAT YOU USE A QUALIFIED INSTALLER TO CARRY OUT
THE INSTALLATION.
If you have any other enquiries, please contact the dealer from whom you
purchased your heater.
THIS APPLIANCE WEIGHS IN EXCESS OF 200 KILOGRAMS. EXTREME CARE
SHOULD BE TAKEN WHEN HANDLING THE APPLIANCE.
WARNING
!
Brick Removal
IF BRICKS REQUIRE REMOVAL WHEN PREPARING THE FIREPLACE, ENSURE
THAT YOU DO NOT EXPOSE COMBUSTIBLE MATERIALS BEHIND THE
BRICKWORK OR WEAKEN THE INTEGRAL STRUCTURE OF THE CHIMNEY.
AF Gason Pty. Ltd. accepts no liability whatsoever for any interpretation of AS/NZS 2918:2001.
It is important you understand these installation instructions and minimum clearances to
combustible materials before selecting a position for your Eureka Jewel, to ensure safe and
correct installation is achieved.
Installation permit
Depending on your local authority requirements, a permit may be required for the installation
of your heater. It is your responsibility to arrange the same.
Installation into existing or masonry replace
The Eureka Jewel Insert can be installed into a masonry replace with a ue system that is in
accordance with the relevant sections of AS/NZS 2198:2001.
In a masonry replace installation, the minimum hearth depth of 570mm from the front of
the fascia panel on both sides must be achieved. In the instance the replace is raised above
a combustible oor, and it is desirable to reduce the hearth depth, please refer to the elevated
installation instructions on page 4 for hearth reduction information.
For detailed mantle clearance dimensions, refer Figure 3 on page 4.
If installing the Eureka Jewel under a combustible mantle, a hot air deector must be
attached onto the front of the fascia.
For additional clearance details, or access to the Eureka Jewel Insert Conformance
Certicate, please contact your local Eureka dealer from whom you purchased your heater.
Section showing Installation
Figure 1. Masonry Installation
745
Door to door
Removing heater from pallet:
• Remove 4 x Phillips Head screws holding the transport brackets to the side of the unit.
• Discard transport brackets and Tek Screws used to fasten them to the pallet.
• Re-t 4 x Phillips Head screws to side panels of heater in the original holes.
O/All weight: 240kg
Package dimensions: 910Hx910Wx1000D
To aid heater installation, remove doors, top plate, bae and cast iron liners to reduce overall heater weight.
0$7(5,$/
),1,6+1$785$/
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%< (&11R '$7(
5(9
%< (&11R '$7(
5(/($6('
'21276&$/(


$

6&$/(
3$571R
'225+($7(5)6
%$6(+($7(5
77
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU  
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

841
Total width
692
875
751
708
Figure 11
644
685

Jewel Insert 4 Jewel Insert 13
Firewood
Getting the most out of your rewood
Firewood is a sustainable source of energy and when used correctly can provide a cost eective form of heating in your
home. Too often poor heating results and operational issues are attributed to using unseasoned wood which leads to
excess smoking, causing creosote buildup and dirty glass. Wood should be stored in a dry place where good ventalition is
available. Freshly cut wood should be stored for between 12-24 months before burning.
Use only hardwood with your Eureka Jewel.
Thermal eciency
A wood’s eciency does not depend only on its type, but also on its moisture content as well as the temperature of the
combustion chamber. To achieve a greater eciency and longer burn cycle out of your Eureka Jewel, without the emissions
of hazardous particulates, your wood must be well seasoned.
Ideally, wood should not be burnt when its moisture content is above 20%. A moisture meter to measure moisture content
is a handy addition.
0% moisture
100% thermal eciency
10% moisture
88% thermal eciency
30% moisture
63% thermal eciency
50% moisture
39% thermal eciency
An example of available thermal eciency for a piece of wood as a fuel source at varying moisture levels.
The combustion process of burning wood
When wood is heated up to approximately 100 degrees celsius, moisture begins to evaporate from the fuel. There is no
heating value from the wood at this point. As moisture releases from the wood, it reduces the eciency of the combustion
process robbing heat energy from the wood. This demonstrates the importance of dry and well seasoned wood.
As rebox temperatures reach 250-300 degrees celsius, wood solids begin to break down and release volatile gases which
ignite and produce heat.
From 300+ degrees celsius, the main energy available from wood is released when fuel vapors containing up to 60% of
the wood’s potential heat is released.
Understanding combustion principles and learning how to manipulate various conditions surrounding the operation of
your Eureka Jewel enables you to achieve maximum comfort and eciency from your Australian made wood heater.
Figure 14
Installation (continued)
Hearth & oor requirement
If the Eureka Jewel will be installed directly onto a non-combustible oor such as brick, stone or concrete slab with tiles, etc.
which extends beneath the appliance as well as 570mm in front of the appliance fascia on both sides when in position, a hearth or
oor protector may not be required.
At a minimum, the oor protector must extend 570mm in front of the appliance fascia on both sides, with a minimium overall depth
of 1890mm and must be 940mm wide.
If the Eureka Jewel and hearth is to be installed directly onto or partially onto a combustible oor, a minimum 32mm thick
non-combustible hearth or oor protector (cement sheet, Bellis Board, Hebal, stone or masonry, concrete etc.) must be placed
in between the appliance and the combustible oor, directly beneath the unit. If the base of the unit is to be installed at an elevation
less than 118mm above the top surface of the hearth, minimum hearth thickness is also 32mm. If the unit is installed at an
elevation of 118mm or more from the the top surface of the hearth to the base of the unit, minimum hearth thickness (excluding
directly below the unit) is reduced to 6mm.
Elevated installation
In some instances it may be desirable, or required that the Eureka Jewel Insert be installed into an existing replace which is
raised above a combustible oor. In this situation, the minimum required hearth can be reduced to the corresponding
elevated height dimensions mentioned in Table 1.
Scenario - The appliance is to be installed into an existing brick masonry replace which is situated 100mm above a
combustible oor, at this height the minimum required hearth depth is 448mm in front of the appliance fascia. (refer Table 1.)
When the appliance is raised 176mm or more above a combustible oor, a 300mm non-combustible hearth or oor protector
is always required as per AS/NZS 2918:2001.
MinimumAppliance
Hearth Dept raised by
X Y
Table 1. Appliance height
vs hearth requirements
570
553
530
505
478
448
433
420
416
398
379
359
338
315
300
300
Elevated installation details
(dimensions in mm)
0
20
40
60
80
100
110
118
120
130
140
150
160
170
176
>176







0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%< (&11R '$7(
5(9
%< (&11R '$7(
5(/($6('
'21276&$/(


$

6&$/(
3$571R
,1%$66(0%/<
(85(.$-(:(/-,1'$5$63(&75(
77
(1*35 
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU  
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

 77
Elevated installation example - Figure 2
250
240
435
Y
X
940
H
H
Minimum
Hearth
Thickness
32
32
32
32
32
32
32
6
6
6
6
6
6
6
6
6

Jewel Insert 12 Jewel Insert 5
Removing the fascia
• Turn the fan power off, and removed the three pin plug from the power point.
• Open the door 25mm and lift door off hinge, place door on a soft flat surface.
• Undo x4 M8 button head cap screws which attach the fascia to the main firebox.
• Gently lift the fascia away from the front of firebox, but do not pull away fascia completely, leave the fascia rest on the hinge while
removing the fan switches.
• With the fascia resting on hinge, reach behind the switch panel and undo x2 wing nuts and remove switch panel.
• With switch panel removed, fascia can now be completely moved away from the heater to gain access to the fan and wiring looms.
Installation
Operating your Eureka
Troubleshooting
• Noisy Fans
Turn the power o and remove the three pin plug from the power point. Remove the door on one side of the unit,
then remove the fascia panel. Loosen the fascia ll panel retaining screws and lift panel up then out to remove.
Note that wiring and switches are atached to this panel.
Disconnect the wiring loom via the plastic joiner. Unscrew the wing nuts which hold each fan in position and remove
the fans. Clean any dust with a dry paint brush and vacuum the fan blades. Clean around the motor. After completion
place two or three drops of sewing machine oil on the shafts at the bearings. Replace the fans in reverse to the removal.
•Fans not working
and both switches are rmly connected. If the fans still fail to function, remove the fans and switches by rstly removing
the knob from the rotary switch by pulling it away from the heater. Undo the holding nut and pull the switch out.
Squeeze locator tabs together on the rear of the thermostat switch and push through outside of pedestal.
Disconnect the wiring from the power lead and remove the fans. Convey the same to the authorised Eureka dealer from
whom you purchased your unit for service.
Replace in the reverse order.
• Air control jamming
Access to the airside is available when the door is opened.
There are three screws holding the air slide in place. Undo them and remove the air slide. Wipe any ash or dust that may
have accumulated on the back of the air slide or on the face of the heater. If any burrs have developed on the back of the
air slide or on the face of the heater, rub them o with ne wet and dry sand paper till you have a smooth surface and
edges. Replace the air slide and make sure the washers, springs and spacers are tted when you screw the bolts back into
the face of the heater. Do not apply any type of lubricant to the air slide whatsoever as this will attract dust and make the
slide stick.
• No overnight burn
Remove the air slide as per air control jamming and check if the air slide is hard against the face of the heater. If it is
loose, tighten up the bolts holding the air slide to the face of the heater. Do not overtighten.
Check that the door rope has an even indentation from its contact with the face of the rebox. If it is uneven
and it appears as though air could leak through the seal,the door hinge and latch can be adjusted or the door rope may
need to be replaced. Refer door adjustments and rope replacement instructions.
WARNING
!
Overring
TO PREVENT OVERFIRING OF THE HEATER, NEVER OPERATE THE HEATER WITH THE
DOOR LOOSE, OR SUCH THAT THE FIREBOX IS NOT AIR TIGHT. OVERFIRING COULD
RESULT IN DETRIMENTAL WEAR AND TEAR ON THE FIREBOX AND FLUE SYSTEM.
Check the power connection with another appliance. If the power point is O.K. shift focus to the fan or the switches.
Move thermostat switch into the ‘Overide’ position, and select one of the three fan speeds. If the fans fail to function,
isolate power as above, remove pedestal ller panel to gain access to loom. Check that the terminals on the loom
• Excessive ash build up
Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the wood
which is most convenient for you, as long as it is dry. After a period of time you will get to know when to empty your unit.
Bark will give you excessive ash. Try not to burn it. If you are burning wood that gives you charcoal, you may nd that after
running the heater say for 8 hours at maximum burn rate, the charcoal builds up excessively. An overnight burn will reduce
this charcoal back to a ne ash. If you are not ready to shut down for an overnight burn when you next fuel the heater, load
the heater with only one piece of wood and lay it across the rebox on top of the charcoal. Open the air control wide open
and you will nd the charcoal will burn down with the one piece of wood. Repeat the process until the ash level is
signicantly reduced.
• Excessive smoking - smoke entering the room maybe caused by:
• Insucient length of ue (ue to be 4500mm minimum underneath the base of heater to underside of cowl)
Increase height of ue
• Flue downdraught - Consult dealer or increase height of ue.
• Creosote build up in ue - Remove cowl and clean ue as per cleaning instructions. Check moisture content of
wood.
Installation (continued)
Final inspection prior to use
• Ensure the baffle is firmly located and in the correct orientation.
• Ensure cast iron liners are positioned correctly.
• Check fan cord has not been damaged during transit.
• Plug in fan cord and ensure cord does not touch heater surface.
• Switch thermostat switch to ‘Override’ and select one of three speeds to
ensure fan is operational.
• Check door seals are in place.
Bae System
WARNING
!
Bae System
If the bae system is damaged, burnt out, discarded or not installed as per these
instructions, high ue temperatures, losses in combustion eciency and excess
smoking can occur.
To operate this appliance as it is intended, and to ensure product longevity is
achieved, ensure the bae is installed as per these instructions.
If rebox, ue failure or excess damage to the appliance or its surroundings is
reported due to incorrect installation or operation of the Insulated Bae System,
AF Gason Pty. Ltd. reserve the right to disallow any warranty or claims in relation to
the abovementioned.
Placement of Cast Iron Liners into rebox
The cast iron liners are to be positioned with ribs and logos facing into the
rebox.
To install cast iron liners, align the lower recesses of the cast iron liner and
the retaining tabs in the rebox, then slip the liner over the retaining tabs
and lower into position. Reverse this procedure for liner removal.
Fitting the steel bae
CAUTION - Steel bae is heavy (15kg) - seek assistance
when carrying out bae removal/installation.
1. Feed the baffle plate through the door opening
with the upturned edges facing towards the
door opening. Position the baffle in roughly the
centre of the firebox.
2. Lift one edge of the baffle up over the baffle
support bracket, lifting the raised edge as far
into the upper corner of the firebox as possible.
3. Lift the other edge of the baffle up so that it
is also above the height of the baffle support
brackets.
4. Shift the baffle sideways so that it locates in the
baffle supports on both sides of the firebox.
5. Ensure that the baffle is sitting level and that it
is securely located in the baffle supports.
Figure 3
Bae Support
Bracket
Steel Bae
Cast IronLiner
LinerRetaining Tabs

Jewel Insert 6 Jewel Insert 11
Installation (continued)
3000mm 3000mm
3000mm 1000mm
min if clear
within
3000mm of
ue top
Increase from
1000mm min
until clear
within 3000mm
of ue top
600mm min
More than 3000mm
600mm min
More than 3000mm
or less
3000mm
or less
Increase as
necessary
until
nothing
within
3000mm of
ue top
Any nearby
structure
3000mm
The ue pipe shall extend not less than 4.6m above the top of the oor protector. Note: Installation must be
carried out by a licensed installer in accordance with AS/NZS 2918:2001.
Flue pipe casing
Flashing
3 x ue diameter
from active ue to
heat sensitive
surface
Batten
Flue
pipe
Flashing
Flue pipe casings
Heat sensitive roof
25mm
25mm
25mm
Flue pipe
Gap 25mm
Gap 25mm
Roong
Batten
Ceiling
Ceiling Plate
See clause 4.6.3(b) of AS/NZS 2918:2001
25mm
12mm
25mm
178mm dia
Example of sloped ceiling penetration
Example of roof penetration
Rafter
See clause 4.8 of AS/NZS 2918:2001
Flue and chimney requirements
Figure 4
Figure 5
Basic Spare Parts













 












 













 
,7(0 3$571R '(6&5,37,21 47< 6,=(
%207DEOH5HVWUXFWXUHG
 
1870:+,=/2&.)/$1*(
&/
 
  6&5(:6(70[32=,=3  
  6&5(:7(.[6(/)7  
  63$&(5$,56/,'(/,1.$*(  $
  187:+,=/2&.)/$1*(066  
 
6&5(:6(70[[3+(;
*5=3
 
,7(0 3$571R '(6&5,37,21 47< 6,=(
%207DEOH5HVWUXFWXUHG
  3$1(//,1.$*(  $
  3$1(/$,56/,'(  $
  52'$,56/,'(  $
  6&5(:6(70[3+'%/$&.  
,7(0 3$571R '(6&5,37,21 47< 6,=(
%207DEOH5HVWUXFWXUHG
  635,1*667((/$,56/,'(  
  :$6+(5)/$7[[PP  
  63$&(5$,56/,'(  $
  6:,7&+7+(50267$7'(*  
 
6&5(:6(70[&681.
%/$&.
 
  187:,1*0=3  
  :$6+(5)/$7[*=3  $
  6&5(:7(.[6(/)7  
  &$7&+$66(0%/<  $
  /$7&+%/2&.6+,0  $
 
:$6+(567$50
,17(5/2&.,1*=3
 
  +,1*(6+,0  $
  *5200(7&25'*5,3  
 
*5200(758%%(5%/,1'PP
/5
 
  *5200(70+($75(6  
  :$6+(5)/$7[[*  
  %86+$,56/,'(  $
  .12%32:(56:,7&+  $
  )$16:,7&+63(('527$5<  
 
6:,7&+326,7,2163'721
21
 
  %$))/(3/$7(  $
  &$67,521/,1(55($5  $
  %/$1.,1*3$1(/  $
  )$1$66<7:,1:+((/  
  '225$66<  $
  6&5(:&$30[%87+'  
  6&5(:6(70[[3%/$&.  
  :$6+(5)/$766[[  
  +,1*(  $
  3$1(/,1),//)$6&,$  $
  )$6&,$7+58:$//,1%8,/7  $
  ,16(57$66<-(:(63(&75(  $
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9
%< (&11R '$7(
5(9
%< (&11R '$7(
5(/($6('
'21276&$/(


$

6&$/(
3$571R
,1%$66(0%/<
(85(.$-(:(/-,1'$5$63(&75(
77
(1*35

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU  
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

 77
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
233888
233884
230568-10
230980
907424
917333
922334
230565
203903
234278
231030
233881
232037
231049
227074
204184
906103
213321
221328
203651
234101
910106
234016
234015
213151
906201
213164
917119
214289
213098
907400
212974
917209
231804
233882-01
233883-01
917203
903206
234811
203902
208177
903205
Ref. GPN Description Ref. GPN Description
Insert Assy
Fascia Assy
Fascia Fill Panel
Hinge
Washer Flat M8 x 20
Screw Set M8 x 20
Screw Cap M8 x 20
Door Assembly
Twin Barrel Fan
Blanking Panel
Cast Iron Liner
Steel Bae Plate
Switch - 2 Position
Switch - 3 Position
Switch Knob
Air Slide Bush
Washer Flat 3/16” x 9/16”
Rubber Grommet
Rubber Grommet Blank
Grommet Cord Grip
Hinge Shim
Washer Star M8
Latche Block Shim
Catch Assembly
Tek Screw 10 -16 x 16
Washer Flat 1/4”x 3/4”
Wing Nut M6
Screw Set M5 x 20 C/Sunk
Thermostat Switch
Air Slide Spacer
Washer Flat 10 x 18
Air Slide Spring
Screw Set M6 x 20
Air Slide Rod
Air Slide Panel
Linkage Panel
Set Screw M6 x 25
Nut M6
Spacer - Air Slide Linkage
Tek Screw 10-16x25
Screw Set M5x15
Nut M5
Figure 9

Jewel Insert 10 Jewel Insert 7
(continued)
Replacing your glass
• Open door and lift free of hinge.
• Place door face down on a soft flat surface to protect paintwork and glass.
• Remove glass retainers by removing 6x M6 whizlock nuts.
• Lift door frame away from glass. Note how the 6mm OD glass sealing rope is
placed around the door frame - dispose of old glass safely.
• Fit new 6mm OD glass sealing rope onto the door frame with new 14x dart
clips. Ensure outer corner and middle horizonal clips are positioned with the
pointed extrusion pointing outwards, with all other clips pointing inwards.
• Place the glass back onto the door frame with the 6mm OD door sealing rope in position.
• Fit glass retainers back to top and bottom of the door, and attach to door frame with the 6x M6 whizlock nuts. Tighten
nuts evenly until the retainer holds the glass. Do not over tighten the retainers as this could break the glass.
• Mount door back onto hinge, close and ensure fitment is safe and correct.
Fitting a new door seal
• Open door and lift free of hinge.
• Place the door face down on a soft flat surface to protect the paintwork and glass.
• Remove old rope and scrape old glue from rope retaining groove.
• Clean the rope retaining groove with a clean, dry cloth to remove any old dust and debris.
• Apply a generous bead of roof and gutter silicon around the rope retaining groove.
• Press the new 19mm OD door rope into the rope retainer groove, placing the start-stop joint to the bottom corner of the hinge
side of the door.
• Refit door and close to apply pressure to the new rope.
Note: Hinge and door catch may need to be adjusted to allow the door to close completely if previously adjusted to accommodate
an ageing rope.
• Leave door closed for at least 12 hours before lighting the heater, and initially run at a low temperature to allow adhesive
to fully bond to the door.
Maintaining & Servicing your Eureka
Figure 8
203603 Rope 19mm OD
230566 Door Frame
230922 Glass
230954 Retainer
231069 Rope 6mm OD
231070 Dart Clips
231805 Handle
903206 Nut Whizlock M6
904300 Nut Conlock M5
907204 Washer M6x12.5
907406 Washer 5.5x10x1
932202 Screw M6
231816 Shaft
231818 Latch
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Ref. GPN Description
Operating your Eureka
WARNING
!DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITHOUT READING AND
UNDERSTANDING THESE OPERATING INSTRUCTIONS THOROUGHLY. FAILURE TO
OPERATE THIS APPLIANCE PROPERLY MAY CAUSE UNDUE DAMAGE TO THE
APPLIANCE OR RESULT IN A FLUE FIRE.
Read these instructions
Starting your re
Place a relighter or paper in the bottom of the rebox and place a large amount of small kindling on top. Ignite the
paper or the relighter. Set the air control to High and leave the main door open approximately 25mm.When the kindling
is burning, place about four pieces of small wood on top of the burning kindling. Once the wood is alight, close the main
door.After approximately 20 minutes, turn the air control down to Medium. For fan operation refer page 8.
On the initial re up you may detect smoke coming from the paint nish and from any oils that may be on the steel on
the outside of the rebox.This is normal. It is suggested to well ventilate your home on the initial re up. Please refer to
our section ‘Paint Curing and Care’ on page 2.
The glass door
Always operate your heater with the door closed and locked.The only time you can leave the door open is on initial
lighting, or when reloading the heater.
Care of your glass
If you are burning good dry wood, you will have very little discolouration of your glass in normal burning cycle. If you aim
for an eight to ten hour overnight burn, you should not get much discolouration.You can control this by adjusting the air
control, moving from the left and slowly creeping the control to the right.After a number of days you will nd the right
position to suit your requirements and the fuel that you are using.
Daily operations
When you get up in the morning, open up the air control of the heater to High position to start the embers glowing. Place
three or four pieces of wood on top of the embers and leave the door open 25mm. Once the fuel starts to ame close the
door. Depending on your daily heating requirements, operate the fan as per fan operation instructions on page 8.
For best results it is best to burn 410mm long wood and load your wood straight into the rebox front to rear. This will
give optimum eciency and recoverable heat, and minimise creosote formation and smoke emissions.
Overnight burn
Approximately 30 minutes before turning the heater down for the overnight burn it is recommended to load the heater with
fuel. Leave the air control in the Medium to High position. Let the heater run for about 30 minutes. This will reduce the
moisture content in the fuel before shut down. (This will help reduce the creosote formation in the rebox and ue.)
Set the air control to the setting you have found best for your requirements. Turn the fan o or to the thermostat control
position and retire. The aim when overnight burning is to have only a few hot embers left in the bottom of the rebox in
the morning, not huge lumps of wood.

Jewel Insert 8Jewel Insert 9
Operating your Eureka (continued)
WARNING
!
Operation of the Fan
If rebox failure is reported and it is found that the rebox has been abused
through improper use of the fan, AF Gason Pty. Ltd. reserve the right to disallow
any warranty claims in relation to rebox failure.
WARNING
!
The Door
Leaving Door Open
As stated previously, leaving door open 25mm encourages the re
to pick up at a faster rate. Your heater has been tested to ensure that no
structural damage can take place if the door is inadvertently left open. However
your paint nish can be damaged if the door is left open for a long period with a
full rebox of fuel with the fan o. Closely supervise your heater while the door is
left open.
Closing the Door
Always ensure that before you close your door there is no wood protruding
beyond the front of the rebox opening. Do not use the door glass as a ’battering
ram’ to push the wood back into the rebox.Damage to the glass by such
impact is not covered by your warranty.
Fan operation
Your Eureka Jewel is equipped with a temperature-sensitive thermostat switch located within the heater’s pedestal beneath
the rebox, which when selected will turn the fan on and o depending on the temperature of the rebox.
To use the thermostat, select the thermostat ‘On’ position via the thermostat switch, and select the desired fan speed you
wish to use (Low, Medium or High).
If the fan is not coming on at the desired time, ip the switch into the Override position and operate the 3 speed fan as
described below:
• Initial Startup (cold)
Leave fan off until the heater is hot and has established a
coal bed - approximately 20 minutes after fuel is lit.
• Medium or High Burn Setting
If the heater is running above medium fire for extended periods
of time, fan speeds Medium and High are recommended.
High is recommended for short bursts where a quick temperature
rise is desired in conjunction with a high fire setting.
• Low Burn Setting
The fan cools off the firebox, robbing the combustion process of efficiency.
It is acceptable to turn the fan off, only when the heater is burning a low fire.
Note: Improper use of fan can result in firebox failure.
The fan should be cleaned on a regular basis. (Refer Troubleshooting for fan removal and cleaning.)
Rotary switch
Thermostat switch
Thermostat ‘On’
Thermostat ‘Override’
Figure 6
Maintaining & Servicing your Eureka
Catch Assembly
Latch Shim/s
Retaining Screws
Cleaning your ue
Firstly and carefully remove cast iron plates and bae system and put to one side. Close the heater door. Obtain a 180mm
ue brush from your local Jindara Dealer and proceed to the top of the ue. Remove the ue cowl. Slowly push the
brush down the ue until it stops. Pull the brush back out and repeat the process. Each time you do this you will notice
that the brush will go further down the ue until it reaches the bottom. The soot and creosote will fall down the ue and
into the rebox. Clean residue from rebox. Replace the bae platerst followed by the cast iron liners.
Make sure you do the job well.The cleaner the ue the less chance there will be of the creosote sticking again. After you
replace the cowl, inspect the roof ashing for any damage that may have incurred whilst you were cleaning the ue.
Reseal the seal on the roof with roof and gutter silicon if required.
Cleaning the glass
Generally the only time you will possibly need to clean your glass is after a long overnight burn. If you nd that you have
a wet sticky black lm on your glass (creosote), it is better to burn the heater as normal for one load of wood.When the
wood has burnt down to a hot bed of embers, open the door and leave it wide open until the glass cools suciently to
be wiped with a damp cloth.This should clean all the white smoky lm o the glass. Creosote on the glass is normally a
sign that you have tried to get too long an overnight burn or you have burnt excessively wet or green wood. If the lm on
the glass won’t come o with a wet cloth, you can use wet ash from the ash bed as a cleaner or commercial products
such as Crystal Clear, Johnson Foam Clean or Windex.
To maintain an ecient and safe use of your Eureka Jewel, you may need to
adjust the door hinge and catch over the duration of its life.
Adjusting door catch
• Open door to gain access to catch.
• Using a 3mm Allen key, remove the two catch retaining screws and set aside.
• To tighten the latch, remove one shim. To loosen the latch, t an additional shim.
• Additional shims are available from your Eureka dealer. Refer to gure 7-1.
• Once the desired setting has been achieved, re-t the catch assembly using the
two retaining screws.
• Note that if an adequate seal cannot be achieved through the removal of one
shim, a replacement door rope may be required.
Adjusting door hinge
The door hinge denes the door alignment to the heater and the door catch,
as well as determining the amount of pressure applied to the main door rope
at the hinge side of the door.
To align door:
• Slightly loosen 2 x M8 Bolts securing the hinge to the heater. The upper
bolt should be loosened 1- 1+1/2 turns, while the lower bolt should only be
loosened 1/2 a turn.
• Align door horizontally by pivoting the door about the lower bolt. Note
that there is no provision for lateral adjustment of the door hinge position.
• Check that the fascia is square to the firebox by measuring from the base of
the fascia to each end of the ash lip. Adjust the fascia as needed if
measurements are not equal.
• Check the alignment of the door by measuring vertically from the
underside of the door at each outer edge, to the base of the fascia, as per
figure 7-2. This measurement should be taken with the hinge bolts
tightened and with the door hanging under its own weight.
To adjust hinge shims:
• Open door and lift free of hinge, and place on a soft at surface while servicing the hinge.
• Remove the door hinge and fasteners as shown in gure 9.
• Remove 1 x hinge shim plate in order to tighten the seal of the door rope. The maximum number of shims permitted
behind the hinge is 2, fitted as standard.
• Fit door and re-align door to catch and firebox before fully tightening M8 bolts.
Figure 7-2
Figure 7-1
Ash Lip Edges
Align With Glass Edge
Measure Height To Door