Greystone F2653BCFW User manual

26 IN.FLAT INSERT ELECTRIC FIREPLACE
MODEL#F2653BCFW
<a®
c us

TABLE OF CONTENTS
Safety Information......................................................................................3
Operation Instructions...............................................................................
.4
Installation Instructions............................................................................. .5
Care and Maintenance................................................................................6
Troubleshooting..........................................................................................7

ASAFETRYINFORMATION
Please read and understand this entire manual befOre attempting to assemble, operate or
Install the product
AWARNING:Any use ofthi, app!iencc othccthen that cecommended by the
Manufacture in thi::. owners manual may cause fire,bums,elcctric shock and /or other
serious injuries or death.
"When using electrical appliances,basic precautions should be followed to reduce the risk of
fire, electric shock and injury to person mcluding the following:
L Read the manufactures instntctions completely before using this appliance.
2. This appliance will become
hot\\ l1en in usc, To avoid bums, do not let bare skin touch
hot surface. The grill at the top of this heater particular will become hot when the heater
is active.Take special care not to block the air intake
or exhaust v~nts.
3. Extreme caution is necessary vvhen the appliance is used by or near children or invalids
and whenever the beater is left operating and unattended.
4. Do not operate the heater if the power cord or plug has been damaged or the heater has
been damaged or malfunctioned
in any way. Take the appliance to an authorized service
facility for examination, electrical or mechanical adjustment or repair.
5. Do not use outdoors.
6. This heater
is not intended fOr use in bathrooms, laundry areas and similar indoor
Locations. Never located heater where it may
fUll into a bathtub or other water container.
7. To disconnect the appliance, turn all controls "OFF", and then remove the plug from the
electrical
outlet
8. The appliance comes equipped with a 3 prong-grounding plug. Do not cut the
grounding prong. Connect to properly grounded 120V outlets only.
9.
Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this
may cause an electric shock or fir~, or damage the appliance.
10. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not
use on soft surfaces, like a bed, where opening may become blocked.
1
I. All electrical heaters have hot and arching or sparking parts inside. Do not usc in areas
where gasoline, paint,
or Jlammablc liquids are used for stored or where the appliance
will be exposed
to 11ammable vapors.
12. Avoid using the appliance with an extension cord. Extension cords may overheat and
cause a risk
of fire, if an extension cord MUST be used, the cord must be No.l6AWG
minimum size and rated not less than 1875 Watts. The extension cord must be a 3-prong
cord with grounding type plug and cord connection and should not exceed 20"(6m) in
Length.
13. 'iVhen transporting or storing the heater, take care to keep both the unit and
power cord/
plug dry, free from excessive vibration and away from heater sources.
14. Use the heater only as described in this manual. Any other usc not recommended by the
manufacture may cause fire, electric shock,
or injury to persons.
15. Do not attempt to burn wood or other materials in this heater.

PREPARATION
"CAUTION: Tbi, b'"t"· ha, fmnt panel made of GLASS' Alway, u" extceme caution when
handing glass. Failure to do so could result in personal injury or personal damage.
This heater is for usc on 120 Volts. The heater has a 3-prong grounded plug (Figure 2.A), If your
electrical outlet has only 2 slots (Figure 2. B), you will have to use an adapter (Figure 2.C) to
convert from the 3-prong power cord to a 2-slot receptacle. The green grounding plug extending
from the adapter must be securely connected
to a pennanentgrolilld such as a properly grounded
outlet box. The adapter should only be used
if a proper 3-slot receptacle is not available.
NOTE: Adapters are not allowed for use in Canada.
~·--
GROUNDING PIN
NOT ALLOWED
IN CANADA
I
1:
(AI
(C)
MATEL SCREW
COVER
OF GROUNDiNG
OUTLET
BOX
ADAPTER
GROUNDING
MEANS
f,
~
. .
(B)
A 15 AMP circuit is required to operate this appliance. If the breaker trips when the appliance is
running, you may need to move the appliance
to another location or unplug other appliances that
are on the same circuit.

CARE AND MAINTENANCE
AWARNINGo Befocc ettempting to pe;lonn eny maintenance on this unit, tum ell controls to
the "OFF" position and unplug. Allow the unit to be "OFF" for at least 10 minutes before any
maintenance applied in order to allow all components to cool down properly.
Cleaning:
1. To remove dust, fingerprints or other marks from glass window, use clean damp cloth. Do not
spray glass cleaner
or other liquid directly onto the glass.
2. Clean metal surtilces with a clean damp cloth making sure not to push dust or debris into any
air intake
or exhaust vents.
3. Do not usc abrasive cleansers or spray liquids on any part
of the appliance.
4. Periodic cleaning vacuuming
of the fan/heater unit is strongly recommended to ensure that no
diti
or foreign objects build up.
Replacing Remote Control Battery
If the remote controls stops functioning or operate poorly, the battery should be replaced with new
one (model# CR2025).
1. The battery compartment can be found on the back side of the remote control.
2. Press and slide the batteJy door to open and remove the old battery.
3. fnscri a
new CR2025 coin battery, making sure that the polarity"+" and"-" atchcs properly as
Illustration showing.
4. Close the battery door.
Warning:
Like with any remote control unit, the remote control unit included with your fireplace may
unwantedly affect
or control other electric products such as TVs. If this occurs, you can change
the encryption on your fireplace remote so that it will not affect other products. To change the
settings on your fireplace remote, hold down the Timer button on the fireplace remote for 3
seconds. To test, use your fireplace remote and see
if your other products are still affected. [f so,
you may change your fireplace remote to a third encryption by again holding down the Timer
button on the remote for 3 seconds. To test this third encryption setting, use your fireplace remote
and see
if your other products are still affected. To get back to the original encryption setting, hold
down the Timer button on the fireplace remote for 3 seconds.
Zero Clearance Fireplace
The electric fireplace has zero clearance safety technology, with the advanced zero clearance
safety sensor,
if there is something covering or closing the slide outs, after about 20 seconds,
the appliance will switch
off power automatically. Then pull the plug out, Let the appliance
cool down for 3 minutes, Plug the
power cord again, the fireplace will be working again.