Euro Appliances E60IDB User manual

cooking
USAGE AND
CARE GUIDE
PRODUCT CODE:
E60IDB
E900IDB

2
SAFETY INSTRUCTIONS AND WARNINGS
This hob is compliant with current safety regulations. Improper use can cause
damage to property and/or to persons.
Read the operating instructions carefully before operating the hob as they contain
important indications for installation, safety, use and maintenance of the appliance.
Observing them avoids dangers for persons and prevents damage to materials.
Keep the user instructions and hand them over to any other users.
Intended use
-This hob is intended for use in the home.
-This hob is not intended for outdoor use.
- Always use within the limits of normal domestic use, not for professional use, to
prepare and keep food warm. Any other use is not permitted.
- Persons who, owing to their physical, sensory or psychological capacities or to
their inexperience or lack of knowledge, are not able to safely use the hob, must
not use it without the supervision and guidance of a responsible person.
These persons can only use the appliance on their own if it has been clearly
explained to them how it works, in order to use it safely. It is important that they
know how to recognise and understand what dangers may derive from incorrect
use of the appliance.
- Persons with heart pacemakers or other electronic implants should consult their
doctor or the manufacturer of the implants to clarify if they provide a sufficient
interference resistance .
Children
- Keep children under the age of eight away from the appliance; alternatively,
supervise them at all times.
- Children over the age of eight may only use the hob on their own if it has been
clearly explained to them how it works and if they are able to use it correctly. It is
important to recognise and understand what dangers may derive from incorrect
use of the appliance.
- Children must not carry out cleaning work on the hob without supervision.
- Supervise children in the immediate vicinity of the hob; do not allow them to play
with the appliance.
- When the appliance is operating it is very hot and remains hot for a certain time
after it has been turned off. Keep children away from the appliance until it has
completely cooled. By doing so, there is no risk of burns.
Risk of asphyxiation!
Children may play by wrapping themselves in the packaging material (e.g. in film) or
wrap it around their heads and choke.
Keep packaging material away from children.
Danger of burns!
Keep items that could attract their attention out of the reach of children, placing
them in compartments above or behind the hob. These items could cause them to
climb onto the appliance.

3
Danger of burns!
Turn the handles and grips of pots and pans sideways, on the work surface, so that
children cannot cling on to them in order to prevent the risk of burns.
-Use the lock function to prevent children from turning on the appliance by
themselves. When using the hob, activate the lock so that children cannot change
the settings (selected).
Danger of electric shock!
Do not turn on the hob or otherwise turn it off immediately if the glass ceramic plate
is damaged or cracked.
Disconnect the hob from the power supply.
Technical safety
- Incorrectly performed repairs or installation and maintenance work can seriously
endanger the user.
Installation and maintenance work, as well as repairs, may only be carried out by
qualified technical personnel.
-Damage to the hob can compromise the safety of users. Check that there is no
visible damage. Never use a damaged appliance.
-Electrical safety is only guaranteed if the hob is connected to a compliant earthing
system. Make sure that this fundamental safety condition is verified. If in doubt,
have the electrical system checked by a qualified technician.
-The connection data (voltage and frequency) indicated on the data plate of the hob
must always correspond with that of the electrical mains, otherwise the appliance
could be damaged.
Compare this data before connection.
In case of uncertainty, contact an electrician.
- Multiple sockets or extensions do not guarantee the necessary safety (risk of fire).
Do not use these devices to connect the hob to the mains.
- For safety reasons, the hob must only be used after it has been recessed.
- Do not use the hob in non-stationary locations (e.g. on ships)
- Contact with live parts or changes to electrical or mechanical structures can
endanger the user and cause malfunctions in the hob.
Never under any circumstances open the casing of the appliance.
-The appliance is not intended for operation with an external programmer clock or
with a remote control system.
SAFETY INSTRUCTIONS AND WARNINGS

4
SAFETY INSTRUCTIONS AND WARNINGS
-The hob must be connected to the electric mains by an electrician. If a damaged
power cord is replaced, a special power cord must be installed by an electrician.
-To carry out installation, maintenance or repair work, disconnect the hob from the
power supply.
The appliance is only disconnected from the power supply if:
- The fuse of the electrical system is disabled or
- The fuses of the electrical system have been completely unscrewed, or
- The plug (if present) has been removed from the socket.
Always hold the plug, never pull the cord.
- If the hob is equipped with a communication module, make sure that the module is
disconnected from the mains during installation, maintenance or repair work.
Correct use
-In case of overheating, greases and oils can ignite easily. Always remain near the
appliance when using greases and oils.
Never extinguish fires caused by oil or grease with water. Turn off the appliance and
carefully smother flames with a fire cover or blanket.
-The flames could ignite the grease filters of the extractor hood. Do not prepare
flambé dishes under the extractor hood.
- If spray cans, slightly flammable liquids or combustible materials are heated, they
can ignite. Therefore, do not store lightly flammable objects in the drawers directly
under the hob. The cutlery tray, if present, must be made of heat-resistant material.
- Do not heat empty pots or pans.
- Cooking to prepare preserves or heating closed tins can result in bursting due to
overpressure.
Do not use the hob to prepare preserves or to heat cans.
When covering the hob, there is a danger that the cover material will ignite, shatter
or melt if the ignition is switched on or the residual heat is removed.
Do not cover the hob, for example with cover plates, a cloth or protective film.
- If an electrical appliance is used in the immediate vicinity of the hob, for example a
blender, make sure that the power supply cable does not come into contact with
the hob. The insulation of the power supply cable may be damaged.
- If the hob has been fitted behind the door of a unit, only operate it with the unit door
open.
Close the unit door only when the residual heat indicators have turned off.

5
SAFETY INSTRUCTIONS AND WARNINGS
- The appliance in operation is very hot and remains hot for a certain time after it has
been switched off. The risk of burns no longer exists only when the residual heat
indicators are turned off.
- If the hob is very hot, there is a risk of being burnt. It is advisable to protect hands
from heat by using special knobs or pot holders. Only use dry gloves or pot
holders.
Wet or damp fabrics are good heat conductors and may cause scalding.
- If the hob is switched on or has been inadvertently switched on, or in the event of
residual heat, there is a risk that metal objects may overheat (danger of burns).
Other types of materials could melt or ignite.
Damp lids could stick to the hob due to the suction effect.
Do not use the appliance as a support surface.
Switch off the cooking zones after use.
- If sugar or food containing sugar, plastic or tinfoil ends up on the hot hob and they
melt, they can damage the glass ceramic surface as they cool. Immediately turn
off the hob and immediately remove these substances with a spatula. Wear gloves
oven.
Clean the cooking zones with a glass ceramic cleaner as soon as they have cooled.
- Pans from which liquids evaporate directly can damage the glass ceramic surface.
Always remain in the vicinity of the appliance when it is operating.
- Pots and pans with a rough base may scratch the ceramic hob. Only use pots and
pans with a smooth base.
- To move cookware it is always advisable to lift it off. This way the surface of the
hob is not scratched.
- Salt, sugar or grains of sand, e.g. derived from cleaned vegetables, can scratch
if they reach the base of the cooking cookware. Make sure that the glass ceramic
surface and the base of the cooking cookware are clean before placing them on the
hob.
- Light objects (e.g. a salt-cellar) that fall over can also crack or damage the glass
ceramic plate. Caution: Do not drop any objects on the glass ceramic surface.
- Hot objects may damage the electronics under the sensor keys and indicator lights.
Never place hot pots or pans on the sensor keys or on the indicator lights.
- Heat up greases and oils for one minute and never use the Booster.

6
SAFETY INSTRUCTIONS AND WARNINGS
- As the induction hobs heat very quickly, the temperature of the base of the pans
can very quickly reach the point of self-combustion for fats and oils. Always remain
in the vicinity of the appliance when it is operating.
- Warning for persons with pacemakers:
bear in mind that in the immediate vicinity of the appliance, when it is operating, an
electromagnetic field is generated. The possibility of a pacemaker's operation being
affected is very remote.
If in doubt, contact the pacemaker manufacturer or your doctor.
- The electromagnetic field of the hob when on can influence the operation of
magnetisable objects.
Credit cards, life-saving devices, pocket calculators etc. must not be found in the
immediate vicinity of a hob when on.
- Metal objects stored in a drawer under the appliance may become red hot if the
appliance is used for a prolonged length of time. Do not store metal objects in a
drawer located directly beneath the hob.
- The appliance is equipped with a cooling fan. If there is a drawer underneath the
recessed appliance, a sufficient distance must be observed between the contents
of the drawer and the lower part of the appliance to ensure the necessary
ventilation of the hob.
Do not store small or pointed objects or paper in the drawer as these may enter the
casing through the ventilation slots or they may be sucked in and thus damage the
fan or impair cooling.
- Never use two pans on a single cooking zone.
- For stationary appliances permanently connected to the fixed wiring, compliance
with this requirement is considered to be met if the instruction concerning
disconnection incorporated in the fixed wiring is in accordance with AS/NZS 3000
Metallic objects such as knives, forks, spoons and lids should not be placed on the
hob surface since they get hot.
The appliance is not intended to be operated by means of external timer or
separated remote-control system.
Danger of fire: Do not store items on the cooking surfaces.
Caution: The cooking process has to be supervised continuously.
After use, switch off the hob element by its control and do not rely on the pan
detector.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.

7
TABLE OF CONTENTS
Safety precautions and warnings ................................................................. 2
Installation ...................................................................................................... 9
General warnings ............................................................................................. 9
Safety distances ............................................................................................... 11
Power cord ....................................................................................................... 13
Wiring diagram ................................................................................................. 14
Start and use.................................................................................................... 15
Description ...................................................................................................... 17
4 Function description.................................................................................... 18
Start .................................................................................................................. 19
Child Lock ......................................................................................................... 19
Key Lock ........................................................................................................... 19
Cooking zone Timer .......................................................................................... 20
Stand-alone Timer............................................................................................. 21
Warming Function.............................................................................................. 22
Booster............................................................................................................... 23
Heat-up Automatic............................................................................................. 23
Pause Function.................................................................................................. 24
Recall Function.................................................................................................. 25
Bridge Function.................................................................................................. 25
User Menù......................................................................................................... 26
6 Function description..................................................................................... 28
Start .................................................................................................................. 29
Child Lock.......................................................................................................... 29
Key Lock............................................................................................................ 29
Cooking zone timer............................................................................................ 30
Stand-alone Timer.............................................................................................. 31
Warming function................................................................................................ 32
Booster............................................................................................................... 33
Heat-up Automatic............................................................................................. 33
PauseFunction................................................................................................... 34
Recall Function................................................................................................... 35
Bridge Function.................................................................................................. 35

8
TABLE OF CONTENTS
Chef Cooking..................................................................................................... 36
User Menù......................................................................................................... 37
Problem and Solution....................................................................................... 39
Safety Device .................................................................................................. 40
Cleaning and maintenance ............................................................................ 41
Environmental protection .............................................................................. 43

9
INSTALLATION
General warnings
•The installation and connection of
the appliance can only be carried out
by a qualified electrician. Contact an
electrician who is knowledgeable of the
local rules and additional regulations
issued by the local electricity operator
and ensure that the work is carried
out in compliance with the same.
The manufacturer is not responsible
for damage caused by incorrect
installation or connection of the
appliance. To prevent damage to the
appliance, only recess it after installing
the wall units and the extractor hood.
•The electrical safety of the appliance is
only guaranteed if it is connected to a
compliant earthing conductor. It is very
important to verify that this condition
is fulfilled as it is a fundamental
premise. If in doubt, have the system
checked by a specialist technician.
The manufacturer is not responsible
for damage caused by the absence or
interruption of the earthing conductor.
•The appliance must not be connected
to the mains with an extension cord;
extensions do not guarantee the
necessary safety of the appliance.
•The hob cannot be recessed above a
dishwasher, a tumble drier, a washing
machine, a refrigerator, a freezer, an
oven or a cooker without a fan for
cooling of the appliance.
•On the one hand, partly high emission
temperatures can damage these
appliances, on the other ventilation of
the hob is not guaranteed.
Only recess this hob on ovens or elec-
tric
cookers equipped with a fume cooling
system.
•If there is a drawer under the appliance,
do not store flammableobjects in it (e.g.
spray cans).
•Make sure that the connection cable
to the hob electrical system is not
subjected to mechanical stress after
installation (e.g. due to a drawer).
•The worktop veneers must be prepared
with a heat-resistant adhesive (100°C)
so that they cannot detach or become
deformed. The end wall profiles must
be heat-resistant.
•On one side and on the back side of
a recessed glass ceramic hob there
can be walls or furniture of any height,
while on the other side any piece of
furniture or appliance present must not
be higher than the hob.

10
ATTENTION:
In order to ensure correct operation of the appliance, a gap of at
least 5 mm must be left for the length of recessing on the front of
the unit during installation.
This is because the electronic controls are equipped with a
protection device which, when the temperature of the electronic
part exceeds 85°C, turns off the hob until it returns below
this limit. During operation then a fan comes on to guarantee the
necessary air flow to avoid exceeding of the temperature limit.
Therefore provide the installation with an underlying protection
that in any case guarantees a flow of air from the back of the unit
or, if the hob is installed above an oven, a type of insulation that is
adequate to ensure that this temperature is not exceeded. In the
case of overtemperature, the electronic part may fail, for which the
manufacturer declines all responsibility.
INSTALLATION
NOTCH DIMENSIONS
•Make the notch in the worktop according to the dimensions relative to the model
(see figure above).
•Respect the minimum distance of 50 mm towards the rear wall as well as to the
right or left towards any side wall.
•Turn the hob upside down and
apply the seal supplied with the
accessories kit to the outside
edge evenly.
510
049
5 06
805
(860)
(900)
() = dimensions for E900IDB

11
INSTALLATION
If the appliance is installed above an extractor hood, the safety distance indicated
by the manufacturer of the hood must be respected. In the absence of precise
indications or if the appliance is fitted with highly flammable materials (e.g. a shelf),
the safety distance must be at least 760mm.
If several appliances are installed under the extractor hood, for which different safety
distances are envisaged,
observe the greater safety distance indicated.
Safety distance to the sides/rear wall
When recessing a hob, on the back and on the side (on the right or on the left) there
should preferably be unit or room walls (see images above)
-50mm minimum safety distance on the back from the notch of the worktop to the
rear edge of the same.
-50mm minimum safety distance on the right and/or left side of the worktop notch to
the adjacent unit (e.g. column unit) or to the wall
DISTANCE BETWEEN APPLIANCE AND
EXTRACTOR HOOD
RECOMMENDED
NOT RECOMMENDED NOT RECOMMENDED

12
INSTALLATION
Intermediate shelf
The installation of an intermediate shelf under a cooking hob is not necessary but is
permissible.
To lay an electrical power cord, prepare a 10mm slot on the back.
To allow better ventilation of the hob, it is advisable to leave a 20mm slot.
Downward safety distance
To guarantee correct ventilation, it is necessary to maintain a minimum distance
between the appliance and an oven, an intermediate shelf or a drawer.
The minimum distance between the lower edge of the hob and
- the upper edge of an oven must be 15mm
- the upper edge of an intermediate shelf must be 15mm
- the bottom of a drawer must be 75mm
Safety distance from the niche covering
If a covering is applied to the niche, a minimum distance must be observed between
the worktop niche and the covering as high temperatures can damage or modify the
materials.
If the covering is made of flammable material (e.g. wood), the minimum distance
between the worktop and covering must be 50mm
If the covering is made of non-flammable material (e.g. metal, natural stone, ceramic
tiles), the minimum distance between the worktop and covering notches must be
50mm less the thickness of the covering.
Example: covering thickness 15mm
50mm - 15mm = minimum distance 35mm
Electrical connection
The appliance can only be connected to the electrical network by a qualified
electrician who is fully familiar with the general specific regulations of the local
electricity company in force and who operates in compliance with the same.
Absorbed power
See data plate
Connection and protection
The necessary connection data is indicated on the plate and must correspond to that
of the mains.
Determine the various connection possibilities from the relevant diagram.
Differential switch (circuit breaker)
For greater safety, it is advisable to include a circuit breaker with 30mA
disconnection current
Separation devices
The device must be deactivated by means of disconnecting devices for each pole.
(When the device is switched off, the contact opening must be at least 3mm). The
disconnecting devices are overcurrent protections and protection switches.

13
INSTALLATION
Disconnect the appliance from the power supply
To disconnect the electrical circuit from the mains, after installation proceed as
follows:
- Fuses: completely remove the fuses from the threaded caps or
- Automatic protections:press the control button (red) until the central button (black) orù
- Recess protections: bring the lever from 1 (on) to 0 (off) or
- Differential circuit breaker: Turn the main switch from 1 (on) to 0 (off) or press the
control button.
After separation, make sure that there cannot be a connection to the power supply.
Power cord
-The appliance must be connected by means of a H 05 VV-F type cable (PVC
insulated) or a H 05 RR-F (rubber insulated) of suitable diameter, observing the
connection diagram.
- Determine the various connection possibilities from the relevant diagram.
- The permissible connection voltage and the corresponding connection value are
indicated on the data plate.
Replacing the power cord
If it is necessary to replace the power cord a new one can be obtained from the
manufacturer or from the service centre.
Replacement of the cable must be performed by a specialist expert operating in
compliance with the regulations in force and with the indications of the electricity
supplier
The protective conductor must be screwed to the marked connection point

14
INSTALLATION
Connection diagram
MONOPHASE
230V
TWO PHASE
230/400 V
THREE PHASE
230/400 V
1/2 BURNERS
3/4 BURNERS
5/6 BURNERS

15
START AND USE
Practical tips for use of the
appliances
•Use cooking containers whose
manufacturing material is compatible
with the principle of induction
(ferromagnetic material). The use
of these pots is recommended: in
cast iron, enamelled steel or special
stainless steel for induction. To make
sure that a container is compatible,
simply test it with a magnet.
SUITABLE MATERIAL UNSUITABLE
MATERIAL
Cast iron,
enamelled steel,
special stainless
steel with magnetic
base
Copper, Aluminium,
Glass, Terracotta,
Ceramic, Non-
magnetic stainless
steel
In addition, to obtain the best
performance from the hob:
•Use pots with a flat, thick base to ensure
that they adhere perfectly to the heating
zone.
•Use pots of sufficient diameter to
completely cover the heating zone in
order to guarantee exploitation of all
the heat available.
•Ensure the base of the cookware
is always perfectly dry and clean to
guarantee correct adherence and
durability, both to the cooking zones
and to the pots themselves.
•Avoid using the same pans used on
gas burners: the concentration of heat
on gas burners can deform the base of
the pot, which loses adhesion.
First commissioning
First cleaning
-remove any protective and adhesive lms
- before starting the appliance for the rst time, clean it with a damp cloth and dry it
Commissioning
The metal components have been treated with a special protective product. At rst
start the appliance may emit odours and possibly steam. Even with the heating of
the induction coils, odours may be given o󰀨 during the rst few hours of operation.
With any further use the odour fades until it disappears completely.
Smells and any fumes are not symptomatic of incorrect connection and damage to
the appliance and are not harmful to health.

16
START AND USE
Automatic switch off
Operation time limitation is an additional safety feature to turn OFF cooking zones
after a certain time with no operation to the corresponding cooking zone by the user.
The time after which the cooking zone is turned OFF is mentioned in the table
below.
Each user operation related to the cooking zone will reset this time limit.
COOKING LEVEL MAXIMUM OPERATION TIME (MIN)
Warming level 1 480
Warming level 2 480
Warming level 3 480
1 516
2 402
3 318
4 258
5 210
6 138
7 138
8 108
9 90
P 5/10
Residual Heat Indication
Residual Heat Indication is a safety feature to indicate that the surface of the glass ceramic
on top of a cooking zone still as a temperature >= 60 °C which may cause burns when touch-
ing by bare hands. The 7-segment of the corresponding cooking zone displays an H in this
case .
An interruption of the power supply voltage cancels the residual heat indication even if the
temperature of a cooking zone is >= 60 °C when the cooktop is re-powered.
Overheating
The hobs is designed for an operating temperature of 85 °C max. The operating
temperature is supervised by a temperature sensor on the PCB.
If the temperature on PCB will exceed 85 °C, the whole cooktop will be turned o󰀨
and an error ER21 will be displayed.
Supervision for Permanent Key Activation
The hob are supervised for permanent key activation. If the Hob is activated for
more than 10 s, will go to OFF mode, emit a signal tone for 10 s and display Er03
as long as the permanent detection will be recognized.
As soon as the permanent key activation disappears, the Hob can be operated
regularly.

17
DESCRIPTION
E60IDB
E900IDB

18
4 FUNCTION DESCRIPTION
1On/O󰀨
2Power level setting range with slide bargraph
3Cooking zone selection and power level display
4Timer select Key
5Timer display
6Timer level decrement
7Timer level increment
8Break-Recall function key
9Key-Lock function
10 Warming function
11 Egg Timer function
Sensors key
8 9 10 11
213
5
6
7

19
4 FUNCTION DESCRIPTION
START :
Once the hob is switched on, place the pan in the desired area and the
corresponding display will automatically light up on the control panel .
Choose the power level with the slider .
Child Lock
Child lock is a functionality to protect the cooktop against unintended operation, e.g.
by children. If locked, the cooktop may be turned ON, but no cooking zone, heating
level or timer may be selected. The displays for the cooking zones will show .
Child lock stays active even if the power supply voltage is interrupted and recovered.
It has to be de-activated manually (see section de-activation of child Lock).
Activation
Press the front right cooking zone selection key for 3 seconds.
Release the button .
Move on the slider from 0 to 9 . This sequence must be finished within 10 seconds .
The display shows for active child lock .
De-activation
Press any cooking zone select key for 3 seconds
Release the button and move slider to position 0.
This sequence must be finished within 10 seconds .
Key Lock
Key lock is a functionality intended to lock the keys during the cooktop is in
operation or in pause state. This is useful for cleaning purposes (as the touch control
is unable to differentiate a wet cloth from a finger).
Activation
Press special key .
De-activation
Press special key again .

20
Cooking zone timer
Cooking zone timers can be used to switch a cooking zone OFF automatically after
the set time has run out. It can be adjusted within a range of 1 min to 1 h 59 min.
Beneath 10 min, the display shows the current time accurate to the second.
During the time is running, the cooking zone can be operated normally, i. e.
changing the cooking level is possible.
Each cooking zone has an independent timer, i. e. an individual time selection
per cooking zone is possible. If more than one 1 timer is set, the timer will always
display the lowest remaining time.
Activation
Pot is placed on the corresponding zone and a cooking level has been set to this
cooking zone .
- Select the corresponding cooking zone .
The display of the cooking zone shows a . in addition to the select cooking
level.
- Touch the display of the timer.
start to flashing for the next 10s .
- Adjust the desired start time digit for digit with +/-
- Do not perform any action for 10s .
The timer starts counting backwards and the laser cap for the corresponding
cooking zone starts pulsating. If it has reached 0, a signal tone will be emitted; the
timer displays show and the corresponding cooking zone will be turned
OFF.
If the residual heat detection detects a hot cooking zone, an will be displayed
at the corresponding cooking zone.
- Touch any button to disable the signal tone.
The signal tone stops and the cooktop can be operated normally. If no key is
activated, the signal tone will stop automatically .
Notes
- The timer selection is kept for 10 s after the last action.
- Each change resets the selection time back to 10 s.
- If a cooking zone with a running cooking zone timer is selected, the current value
of the timer is displayed on the timer display.
- A timer set for a cooking zone is indicated by the corresponding laser cap above
the cooking zone.
- If more than 1 cooking zone timer is set, the timer value for the lowest time period
running is displayed on the timer display. Additionally, the laser cap for this
cooking zone timer will be flashing.
4 FUNCTION DESCRIPTION