Euroboor F16 User manual

Operators manual
version 1.0 EN
Magnetic drill stand
F16

2
Congratulations on your purchase of the Euroboor F16 portable magnetic drill stand. our model is
designed to produce superior holes quickly and efficiently. Through years of experience, constant
innovation and development, Euroboor is committed to provide you with metal cutting tools and
products to help you be more productive.
Before operating your new magnetic drill stand, please read all instructions first. These include the
Operators Manual and warning label on the unit itself. With proper use, car and maintenance your
model will provide you with years of effective hole drilling performance.
TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND A INSTRUCTIONS

3
Table of contents
1. Safety 4
1.1 General safety instructions 4
1.2 Specific safety information 6
2. Description 7
2.1 Intended use 7
2.2 Description and features 7
2.3 Box contents 8
2.4 Serial number 8
2.5 Technical data 8
2.6 Symbols 9
2.7 Environmental 10
3. Preparation & adjustment 11
3.1 Assembly 11
3.2 Prior to use 12
4. Using the machine 13
4.1 Control panel 13
4.2 Installation of hand drilling machine 14
4.3 Electromagnet 15
4.4 Switching fitted hand drilling machine on and off 16
4.5 Tool lubrication 16
5 Working with operation tools 17
5.1 Twist drills 17
6. Maintenance 19
7. Trouble shooting 21
8. Exploded view & spare part list 22
8.1 Exploded view 22
8.2 Spare part list 23
8.3 Wiring diagram 24

4
1. Safety
1.1 General safety instructions
Do not use this power tool before you have thoroughly read and completely understood this
Instruction Manual and the “General Safety Instructions”, including the figures, specifications, safety
regulations and the signs indicating DANGER, WARNING and CAUTION.
WARNING: When using electrical tools basic safety precautions should always be followed to
reduce the risk of fire, electrical shock and personal injury including following.
Please also observe the relevant national industrial safety regulations. Non-observance of the safety
instructions in the said documentation can lead to an electric shock, burns and/or severe injuries.
This Operator’s Manual including the “General Safety Instructions” should be kept for later use and
enclosed with the power tool, should it be passed on or sold.
WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2. Do not operate the magnetic drill stand in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. The magnetic drill stand may create sparks which may
ignite the dust or fumes.
3. Keep bystanders, children, and visitors away while operating a magnetic drill stand.
Distractions can cause you to lose control.
E ECTRICA SAFETY
1. Magnetic drill stand plugs must match the outlet. Never modify the plug in any way. Do not
us any adapter plugs.
2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is grounded.
3. Do not expose magnetic drill stand to rain or wet conditions. Water entering a machine will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord to carry the magnetic drill stand or pull the plug
from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
5. When operating a magnetic drill stand, use an extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a magnetic drill stand in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
PERSONA SAFETY
1. Stay alert, watch what you are doing and use common sense when using a magnetic drill
stand. Do not use machine while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating drill stands may result in serious
personal injury.

5
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
3. Avoid accidental starting. Be sure switch is off before plugging in. Carrying magnetic drill
stands with your finger on the switch or plugging in magnetic drill stands that have the
switch on invites accidents.
4. Never place hands, fingers, gloves or clothing near cutting area or rotating machine parts.
5. Remove adjusting keys or switches before turning the machine on. A wrench or a key that is
left attached to a rotating part of the machine may result in personal injury.
6. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the magnetic drill stand in unexpected situations.
7. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard
hat, or hearing protection must be used for appropriate conditions.
8. Always use supplied safety chain during any work on non-horizontal components. Mounting
can release.
MACHINE USE AND CARE
1. When using the machine on non-horizontal surfaces, you must use cutting paste. Do not use
oil because the oil can drip into the electronic components.
2. During machine operations, the drill bit must be cooled and lubricated with good quality
cutting or lubrication oil.
3. Use clamps or other practical way to secure and support the work piece to a stable platform.
Holding the work by hand or against your body is unstable and may lead to loss of control.
4. Do not use machine if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
5. Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventive safety measures reduce the risk of starting
the tool accidentally.
6. Store idle magnetic drill stands out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
7. Maintain machines with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edges are less likely to bind and are easier to control.
8. Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the machine operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools.
9. Use only accessories that are recommended by Euroboor for your model. Accessories that
may be suitable for one machine, may become hazardous when used on another machine.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or maintenance
performed by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement parts. Follow instructions in the
maintenance section of this manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock or injury.
•When using this machine, you MUST wear ear and eye protection.

6
1.2 Specific safety information
•Keep your fingers well out of the drill area;
•Avoid touching the drill chips. Contact with these chips when they are hot or fall can cause
personal injuries;
•Always use the safety chain;
•The magnetic drilling machine is suitable for use on steel with a thickness starting from 5 mm,
with zero air gap between the magnet core surface and the mounting surface. Curvature,
coats of paint and surface irregularities will create an air gap. Keep the air gap to a minimum;
•Always place the machine on a flat surface
•Do not clamp the magnetic drilling machine on small or irregularly shaped objects;
•Always place the machine on a surface that is clear of shavings, chips, swarf and surface dirt;
•Keep the magnet clean and free of debris and swarf;
•Do not switch on the machine until it has been mounted and installed according to these
instructions;
•Do not switch on the machine before having checked that the magnetic stand has been
tightened firmly to the mounting surface;
•Adjust the table so the drill bit does not extend into the work piece before drilling. Do not
perform any design, assembly or construction activities on the work piece while the machine
is switched on;
•Before switching on the machine, make sure all accessories have been mounted correctly;
•Always use the recommended speed for the accessories and the material;
•Do not use the machine on the same work piece on which electric welders are being used;
•Use only an appropriate cutting fluid. We offer a range of premium cutting oils and lubricants
which are specially developed and selected for optimum performance and maximum tool life;
•Do not use liquid cutting fluids while drilling vertically or overhead. Dip the drill bit in cutting
paste or apply an appropriate spray for these applications;
•Do not pour cutting fluid into the reservoir while it is mounted in the bracket. Do not allow
cutting fluid to enter the electronic parts;
•Ensure that metal chips or resinous residue cannot lead to blockage of the function;
•In case of jammed cutter disconnect the machine from the power supply, remove the reason
for the jam before turning on the machine again.
RESIDUA RISKS
In spite of the application of the relevant safety regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
•Impairment of hearing
•Risk of personal injury from flying particles
•Risk of burns due to accessories becoming hot during operation
•Risk of personal injury due to prolonged use.
Always try to reduce these risks as much as possible.
A WAYS FO OW THE ORIGINA SAFETY INSTRUCTIONS OF THE HAND DRI ING MACHINE FITTED
TO THE MAGNETIC DRI STAND. In no way Euroboor can be held responsible for any damages
resulting from an unsafe or malfunctioning electric power tool other than supplied by Euroboor.

7
2. Description
2.1 Intended use
This magnetic drill stand is intended for commercial use as a tool to hold and control hand-held
electronic drilling machines, and in that combination drilling materials with a magnetizable surface
using twist drills, in a weather-protected environment using the application tools and accessories
recommended by EUROBOOR.
The magnetic drilling machine can be used horizontally, vertically or overhead.
2.2 Description and features
[image 1-1]
1
Adapter ring
2 Tool holder
3 Feed handle
4 Magnet indicator
5 Motor switch
6 Magnet switch
7 Electromagnet

8
2.3 Box contents
1 Carrying case
1 Magnetic drill stand
1 Instruction manual
3 Handles
4 Allen keys (2.5, 3, 4, 5)
1 Safety chain
1 Set of ear plugs
1 Pair of safety glasses
1 Pair of gloves
1 Filler ring inner Ø 38 mm
1 Filler ring inner Ø 33 mm
2.4 Serial number
The serial number is mentioned on the machine 2 times: engraved on the frame and magnet.
Additional serial no. stickers are provided with the machine for your administration.
The serial number will help you and your sales point validate and identify the machine. As example:
F161501001
breaks down to:
F16 15 01 001
Machine series
ear of manufacture
Month of manufacture
Identification number
2.5 Technical data
F16
C AMPING NECK
Ø 43 mm / Ø 38 mm / Ø 33 mm
TWIST DRI S
Ø 1
–
16 mm
ENGTH
260 mm
WIDTH
170 mm
HEIGHT
290
–
450 mm
STROKE
160 mm
WEIGHT
7,5 kg
MAGNET
160 x 80 x 37 mm (L x W x H)
MAGNETIC FORCE
1200 kg
TOTA POWER
70 W
POWER SOURCE
110
–
120V AC / 60 Hz
220 – 240V AC / 50 – 60 Hz

9
2.6 Symbols
Symbol Term, meaning Explanation
Read documentation
Be absolutely sure to read the enclosed
documentation such as the Instruction Manual and
the General Safety Instructions.
Wear ear protection Use ear protection during operation.
Wear eye protection Use eye-protection during operation.
Danger/warning/caution Observe the information in the adjacent text!
European conformity symbol Confirms the conformity of the power tool with
the directives of the European Community.
Class of protection I
Product with basic insulation and exposed
(touchable), conductive parts additionally
connected to the protective earth conductor.
mm Millimeter Unit of measure for length, width, height or depth
kg Kilogram Unit of measure for the mass
V Volt Unit of measure for the electric voltage
A Ampere Unit of measure for the electric current intensity
W Watt Unit of measure for the output
N Newton Unit of measure for the force
min Minutes Unit of measure for the time
no No-load speed Revolution speed at no-load
1/min per minute Unit of measure for number of revolutions,
strokes, impacts or oscillations per minute
.

10
2.7 Environmental
Separate collection. This product must not be disposed of with normal household waste.
Separate collection of used products and packaging allows materials to be recycled and used
again. Re-use of recycled materials helps prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of electrical products from the household, at
municipal waste sites or by the retailer when you purchase a new product.

11
3. Preparation & adjustment
3.1 Assembly
WARNING: To reduce the risk of injury, turn unit off and disconnect machine from power
source before installing and removing accessories, before adjusting or changing set ups or
when making repairs. Be sure all switches are in the OFF position. An accidental start up can
cause injury.
FITTING THE FEED HAND ES
1. Fit each of the three feed handles by screwing them into the hub in clockwise directions
2. Tighten firmly by hand
The handles are supposed to face slightly outward. Be careful not to cross-thread any of the
components.
FITTING THE SAFETY CHAIN
1. Pass the safety chain through the frame grip opening
2. Wrap the chain around the work piece
3. Securely close the chain using the lock
WARNING: Always use the safety chain when using machine vertically and/or up side down.

12
3.2 Prior to use
Please make sure that the contacting surface for the magnet is level, clean and rust-free.
Remove any varnish or primer. When working on materials that are not magnetizable, suitable
fixation devices, obtainable as accessories from EUROBOOR, e. g. suction plate, vacuum plate or
pipe-drilling device must be used.
When work on steel materials with a material thickness of less than 5 mm, the work piece must
be reinforced with an additional steel plate in order to guarantee the magnetic holding power.
Check the machine for possible damage; Before using the machine, you must carefully check
protective devices or slightly damaged components to ensure they are operating perfectly and as
intended.
Check that moving are in perfect working order and do not jam and check whether parts are
damaged. All parts must be correctly installed and fulfill all conditions necessary to ensure perfect
operation of the machine.
Damaged protective devices and parts must be repaired or replaced according to specifications by
EUROBOOR of any authorized EUROBOOR dealer.
DO NOT use under wet conditions or in presence of flammable liquids or gases. This magnetic drill
stand is a professional power tool.
DO NOT let children come into contact with the machine. Supervision is required when
inexperienced operators use this machine.
E ECTRICA SAFETY
The electric magnet and controls have been designed for one voltage only. Always check that the
power supply corresponds to the voltage on the rating plate.
our Euroboor magnetic drill stand is designed in class I (grounded) according to
EN 61029-1. Earth wire is required.
If the supply cord is damaged, it must be replaced by a specially prepared cord available through the
EUROBOOR service organization.
EXTENSION CAB E
If an extension cable is required, use an approved 3-core extension cable suitable for the power input
of this tool (see technical data).The minimum conductor size is 1.5 mm²; the maximum length is 30
meter. When using a cable reel, always unwind the cable completely.
TRY A FEW SIMP E PROJECTS USING SCRAP MATERIA UNTI YOU DEVE OP A “FEE ” FOR THE
MACHINE
ET THE MACHINE RUN IN FOR A PERIOD OF 8-10 HOURS BEFORE STARTING WITH BIG
OPERATIONS. DO NOT OAD THE MACHINE TOO MUCH DURING RUN-IN PERIOD
NEVER USE THE MACHINE IN SERIOUS OVER OAD
KEEP THE MACHINE C EAR FROM MOISTURE AT A TIMES TO PROTECT THE MACHINE, YOURSE F
AND OTHERS.

13
4. Using the machine
WARNING: Always observe the safety instructions and applicable regulations.
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from
power source before making any adjustments or removing/installing attachments or
accessories.
4.1 Control panel
The control panel on your magnetic drilling machine is designed for maximum operating facility and
safety.
1. Magnet Switch
2. Motor Switch
3. Magnet LED Indicator
.
[image 2
-
1]

14
4.2 Installation of hand drilling machine
1. Measure the collar of the hand drilling machine you want to place in the magnetic drill stand.
The magnetic drill stand is suitable for use with hand drilling machines with Ø 43 mm, Ø 38
mm or Ø 33 mm collar.
2. Loosen the bolt on front of the tool holder slightly. Do not remove the bolt.
3. Prepare the tool holder for the hand drilling machine:
a. Ø 43 mm collar: no insert
b. Ø 38 mm collar: insert only the 1 piece adapter ring (outer Ø 43 mm)
c. Ø 33 mm collar: insert only the 2 piece adapter ring (outer Ø 43 mm)
4. Place the hand drilling machine in the tool holder as deep as the collar on the hand drilling
machine allows. Make sure only the collar and no other parts are placed inside the tool
holder (image 3-1)
5. Tighten the bolt on front of the tool holder. Do not overtighten.
6. Check if the rated Voltage and Hertz of the fitted hand drilling machine matches with the
magnetic drill stand.
7. Check if the power plug of the fitted hand drilling machine corresponds with the power
socket on the back of the magnetic drill stand (image 3-2)
8. Place the power plug of the fitted hand drilling machine in the power socket of the magnetic
drilling stand correctly and tightly.
9. Make sure the power cable of the hand drilling machine stays clear of the general drilling
area.
[image 3-1] [image 3-2]

15
4.3 Electromagnet
Make sure the magnetic drill stand is placed on a smooth, clean, level and solid surface without any
objects or debree in between to guarantee maximum adhesion
The workpiece must be at least 5 mm thick for the magnet to stick, but minimal 3 mm thick to hold
the weight of the machine and to drill safely. In case the workpiece is between 3 and 5 mm, make
sure to make a proper base to create a good magnetic field as shown in image 4-1.
[image 4-1]
The electromagnet will work best on surfaces of at least 10 mm thickness.
The electromagnet may not be able to create a good enough magnetic field. Causes may be:
-Surface not flat
-Workpiece not magnetizable (e.g. aluminium)
-Workpiece coated or painted
-Workpiece not thick enough
In this situation the magnet indicator will light up red. Make sure to solve any of these matters
before proceeding in any way and creating unsafe situations
1. Connect the machine to the mains/work piece
2. To activate the magnet, press the red magnet switch
The magnet switch will be lit (red)
The LED indicator lights up GREEN when generated magnetic force is sufficient
3. To deactivate the magnet, press the same switch again

16
WARNING: Do not use this machine when LED indicator is RED. Magnet may not generate
sufficient attachment force
We need to point out that this is only an indication and not a certainly that the magnet will not
release from the material. Euroboor accepts no liability ensuring from the magnet indicator not
functioning or functioning poorly.
Make sure that the magnet attaches tightly to the work piece before turning on the motor unit of the
magnetic drilling machine. Euroboor magnets have 2 coils; make sure that both coils are in contact
with the material. Do not connect any other machines to the electrical outlet the magnetic drilling
machine is plugged into, as it may result in the loss of magnetic force.
Always use the safety chain included. Drilling above your head is extremely dangerous and is not
recommended. For the use of magnetic drilling machines on pipes, not-flat or non-magnetic
materials, we refer to our brochure or our website where several vacuum tightening systems and pipe
clamping systems are mentioned.
4.4 Switching fitted hand drilling machine on and off
The fitted hand drilling machine can only be switched ON when the magnet is activated. To switch
the motor ON, press the green button with marking “I”. To switch the motor OFF, press the red
button with marking “O”.
Be aware that on/off control of the fitted hand drilling machine by the magnetic drill stand can only
be executed when the on/off switch of the hand drilling machine itself is in ON position.
4.5 Tool lubrication
IN HORIZONTA , VERTICA AND OVERHEAD APP ICATIONS
Dip the twist drill bit in cutting paste or apply an appropriate spray.
Make sure to use only suitable cutting oil or fluid. Euroboor offers a wide range of cutting lubricants
for all tool and material combinations. Proper cooling will help you create better and faster results,
and extend the lifetime of your tools.

17
5 Working with operation tools
5.1 Twist drills
DRI ING CONDITIONS
The ease with which material can be drilled depends on several factors including tensile strength and
abrasion resistance. Whilst hardness and/or strength is the usual criterion, wide variations in
machinability can exist among material showing similar physical properties.
The drilling conditions are dependent on requirements for tool life and surface finish. These
conditions are further restricted by the rigidity of the tool and the work piece, lubrication and
machine power available. The harder the material, the lower the cutting speed.
Some materials of low hardness contain abrasive substances leading to rapid cutting edge wear at
high speeds. Feed rates are governed by rigidity of set-up, volume of material to be removed, surface
finish and available machine power.
DRI ING A HO E
Now that you have read the explanatory information and safety recommendations above, you are
ready to actually start drilling. Follow these 12 steps for best drilling result :
1. Install the twist drill according to the original instructions of the fitted hand drilling machine.
2. Precisely mark the centre of the hole
3. Place the magnetic drill frame in the correct position by letting the tip of the twist drill but
meet the marked center of the hole.
4. Switch on the magnet and verify that the drill is in the right position and that the machine is
pushed tight against the work piece.
5. Make sure the fitted hand drilling machine is switched on and (If possible) drilling speed is
set correctly following the original instructions of the fitted hand drilling machine. Switch the
fitted hand drilling machine on with the on/off switch on the magnetic drill stand and allow it
to run at the required speed.
WARNING: Never use the hammer function of a fitted hand drilling machine!
6. Turn the arms to start drilling. Apply only a slight pressure when the twist drill bit touches
the metal. Do not push the twist drill bit with force into the metal.
7. Apply a regular pressure while drilling. The drilling performance does not improve by putting
more pressure on the tool. Too much pressure will overload the motor of the fitted hand
drilling machine and your twist bit will be worn sooner.
Let the twist bit do the job and give it time to cut the metal!!!
8. Apply cooling fluid when necessary. Stop drilling regularly to do so.
9. Apply less pressure when the drill cuts through the material.

18
10. Turn the arms to put the motor in highest position and switch off the fitted hand drilling
machine by pushing the off button on the magnetic drill stand. Then switch off the fitted
hand drilling machine following the original instructions.
11. Switch off the magnet of the magnetic drill base.
12. Remove the burrs, metal chips and clean the twist bit and surface without getting injuries.
Caution: The metal chips drilled out can be sharp and very hot!!

19
6. Maintenance
our EUROBOOR power tool has been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and
regular cleaning.
CAUTION: To reduce the risk of injury, turn unit off and disconnect machine from power
source before installing and removing accessories, before adjusting or changing set- ups or
when making repairs. Be sure the switch is in the OFF position. An accidental start-up can
cause injury.
Just as every magnetic drilling machine with moving parts, your Euroboor magnetic drilling machine
also needs regular maintenance service. A few recommendations follow :
VISUA Y CHECK THE MACHINE FOR DAMAGE
Machine must be checked before operation for any signs of damage that will affect the operation of
the machine. Particular notice must be taken of the mains cable, if the machine appears to be
damaged it should not be used failure to do so may cause injury or death.
C EANING
-Clean all dirt, dust, metal chips and burrs of your magnetic drilling machine
-Blow dirt and dust out of the machine components with dry air as often as dirt is seen collecting
in and around it. Wear approved eye protection and an approved dust mask
-Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool.
These chemicals may weaken the materials used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool
into a liquid.
OPERATION OF THE MACHINE
The machines operation must be checked to ensure that all components are working correctly.
Replace any defective parts immediately. This prevents properly function parts from being damaged.
CHECK MAGNETIC BASE
Before every operation the magnetic base should be checked to make sure that the base is flat and
there is no damage present. An uneven magnet base will cause the magnet not to hold as efficiently
and may cause injury to the operator.
When the machine us put out of use for a longer period, apply a small amount of machine oil to the
underside of the magnetic base for rust protection. Clean the magnetic base again with next use.
ADJUSTMENT OF S IDE
An essential requirement of the machine is that the slide can move in a smooth and controlled
manner, free of lateral movement and vibration.
This situation can be maintained by periodic adjustment of the slide and is accomplished in the
following manner:
1. Place the machine in an upright position and, by means of the capstan, raise the slide to its
highest position. Clean the aluminum rails and apply a small amount of light machine oil to
the wear surfaces

20
2. Gently feed in setting screw with supplied Allen key 2.5 until slight resistance is encountered.
Follow your way down adjusting all setting nuts and screws
3. Operate the slide up and down a few times to test the movement and make any further
necessary adjustments. Try to ensure that all the screws are exerting a uniform pressure on
the slide from top to bottom. A perfectly adjusted slide will operate freely up and down
without any sideways movement
UBRICATING THE FEED TRAVE
The feed travel should be lubricated periodically with grease to ensure smooth operation.
-Raise the motor unit to the highest position possible
-Lubricate the dove-tail guide way at both sides
-Lubricate the gear rack
After repeated use, the gear rack may become loose. If necessary, adjust the 5 self-locking set
screws at the left side. Tighten screws in series until the gear rack moves freely in the dove-tail guide
but does not allow the motor to wobble.
REPAIR, MODIFICATION AND INSPECTION
Repair, modification and inspection of Euroboor magnetic drill stand must be done by EUROBOOR or
an EUROBOOR authorized dealer. The spare parts list will be helpful if presented with the machine to
the Euroboor dealer for service when requesting repair or other maintenance.
Euroboor machines are constantly being improved and modified to incorporate the latest
technological advancements. Accordingly, some parts (i.e. part numbers and/or design) may be
changed without prior notice. Also, due to Euroboor's continuing program of research and
development, the specifications of machines are subject to change without prior notice.
WARNING: Since accessories, other than those offered by EUROBOOR, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only EUROBOOR recommended accessories should be used with this product.
Consult your dealer for further information on the appropriate accessories.