Eurocom Notebook User manual

V12.1.00

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information

contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or

any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear

in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)

of this publication.

This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans-

mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators

of this publication, except for copies kept by the user for backup purposes.

Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade-

marks of their respective companies. They are mentioned for identification purposes only and are not intended

as an endorsement of that product or its manufacturer.

©July 2012

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc-

tive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux-

embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,

United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov-

enia.

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has at-

tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies

to products regulated by certain European health, safety and environmental protection legislation. The CE Mark

is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his

product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE

Marking. A notified body has determined that this device has properly demonstrated that the requirements of the

directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the

notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.

Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference.

And

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator

and your body.

EuP-Standby and Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC)

regulations on power consumption in off mode or standby mode:

• Standby Mode < 2W

• Off Mode < 1W



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex-

pressly approved by the manufacturer for compliance with the above standards could void your authority to operate the

equipment.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury

to persons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 -

240V, 50 - 60Hz DC Output 20V, 15A (300W) minimum).

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam-

aged.

Do not expose the computer

to any shock or vibration. Do not place it on an unstable

surface. Do not place anything heavy

on the computer.

Do not expose it to excessive

heat or direct sunlight. Do not leave it in a place where

foreign matter or moisture may

affect the system.

Don’t use or store the computer

in a humid environment. Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

5. Take care when using peripheral devices.

Do not turn off the power until

you properly shut down all pro-

grams.

Do not turn off any peripheral

devices when the computer is

on.

Do not disassemble the com-

puter by yourself. Perform routine maintenance

on your computer.

Use only approved brands of

peripherals. Unplug the power cord before

attaching peripheral devices.

VIII

Preface

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a steady,

uninterrupted power supply. If you are unsure of your local power specifications, consult

your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong

is an important safety feature; do not defeat its purpose. If you do not have access to a

compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by

its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load

of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power sup-

plies (i.e. AC/DC adapter or car adapter).

Do not plug in the power

cord if you are wet. Do not use the power cord if

it is broken. Do not place heavy objects

on the power cord.



Power Safety

Warning

Before you undertake

any upgrade proce-

dures, make sure that

you have turned off the

power, and discon-

nected all peripherals

and cables (including

telephone lines and

power cord).

You must also remove

your battery in order to

prevent accidentally

turning the machine

on. Before removing

the battery discon-

nect the AC/DC

adapter from the

computer.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides

the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha-

nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-

ture environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

Preface

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly

result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qual-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,

under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with

your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the

manufacturer. Discard used battery according to the manufacturer’s instructions.

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.

Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the

computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the

power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and

screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

XII

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard-

ware and software. Make sure your “papers” are handy.



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a

notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer

from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

XIII

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,

keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very

common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock-

ing the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com-

puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and

disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:

Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.

These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make

sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DCadapter and keep your battery(ies)

charged.

Keep it dry - If you move quickly from acold to a warm location, water vapor can condense inside the computer.

Wait a few minutes before turning it on so that any moisture can evaporate.

XIV

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods of time.

Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or

other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the

level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on

a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when

you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent

and short breaks are better than fewer and longer breaks.

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for

an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.

Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp

edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated

logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during

transport. If any such wear and tear develops contact your distributor/supplier.

XVI

Preface

XVII

Preface

Contents

Notice .............................................................................................................................................................I

FCC Statement ............................................................................................................................................III

FCC RF Radiation Exposure Statement: ....................................................................................................IV

EuP-Standby and Off Mode Power Consumption Statement: ....................................................................IV

Instructions for Care and Operation ...........................................................................................................VI

Power Safety ............................................................................................................................................VIII

Polymer Battery Precautions ......................................................................................................................IX

Battery Precautions ......................................................................................................................................X

Cleaning ......................................................................................................................................................XI

Servicing .....................................................................................................................................................XI

Travel Considerations ............................................................................................................................... XII

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Software ........................................................................................................................................1-4

RAID & AHCI Setup .................................................................................................................................1-4

System Startup ...........................................................................................................................................1-5

XVIII

Preface

System Map: LCD Panel Open ..................................................................................................................1-6

LED Indicators ...........................................................................................................................................1-7

Keyboard ....................................................................................................................................................1-8

Keyboard Backlight LED ..........................................................................................................................1-9

Effects Buttons & Help ............................................................................................................................1-11

TouchPad and Buttons/Mouse .................................................................................................................1-13

Control Center .........................................................................................................................................1-14

System Map: Front & Rear Views ...........................................................................................................1-15

System Map: Right View .........................................................................................................................1-16

System Map: Left View ...........................................................................................................................1-18

System Map: Bottom View .....................................................................................................................1-19

Video Features .........................................................................................................................................1-21

Screen Resolution ....................................................................................................................................1-22

NVIDIA Control Panel ............................................................................................................................1-23

Catalyst Control Center ...........................................................................................................................1-24

Power Options .........................................................................................................................................1-25

Storage Devices, Mouse & Audio

Overview ....................................................................................................................................................2-1

Hard Disk Drive .........................................................................................................................................2-2

Optical Device ...........................................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3