EUROPRO EUROPROLAV 15-200 TH User manual

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510
EUROPROLAV 15-200 TH Diesel
Réf. 11867
User manual
Edition of 22/12/2021
More information on www.euromair.com

User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP2
You just acquired one of our
machines and all the team
of Europe Projection thanks
you for the condence
you have granted us.
Manufacturer of professional
equipments for paint and
llers, we have put our
know-how for 25 years
at the service of the
users of our machines.
Our technical & commercial
team is at your disposal
for any further information
you may need about the
machine you just acquired.
EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET
Tél : [phone]
[e-mail]
SUMMARY
1. USER MANUAL............................................................. p. 3
1.1. Importance of the manual .........................................p. 3
1.2. Receivers of the manual............................................p. 3
2. WARNING .................................................................... p. 4
2.1. Safety .....................................................................p. 4
2.2. End-of-life of the product ..........................................p. 6
3. YOUR MACHINE ........................................................... p. 7
3.1. Description..............................................................p. 7
3.2. Technical characteristics ...........................................p. 7
3.3. Identication of the components ................................p. 8
4. USE OF THE MACHINE ................................................. p. 9
4.1. Prerequisites............................................................p. 9
4.2. Starting up ..............................................................p.10
5. DEFECTS AND REMEDIES............................................. p.11
6. DECLARATION OF CONFORMITY ................................... p.13
7. WARRANTY CONDITIONS.............................................. p.14

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P3
1. USER MANUAL
1.1. IMPORTANCE OF THE MANUAL
This manual is a key part for the use of your machine. It summarizes the procedures of starting-up, cleaning
and maintenance of the device and also the safety instructions you need to observe.
Read carefully all the working and safety instructions and the warnings included in this manual before
starting your machine.
Most of the accidents are caused by the non-compliance of the safety standards and rules.
This manual must be kept near the machine, within reach of the user and held in good condition until the
nal destruction of the machine.
In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page
4 for a copy at any moment.
1.2. RECEIVERS OF THE MANUAL
This manual is intended to any staff which will manipulate the machine :
- people in charge of the transport of the machine
- people in charge of the use of the machine
- people in charge of the cleaning and maintenance of the machine
- people in charge of the nal destruction of the machine

User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP4
2. WARNING
2.1. SAFETY
Using the machine in an incorrect way or in non-compliance of the safety instructions indicated in
this manual can cause death or serious injuries.
Read carefully all the working and safety instructions and the warnings contained in this manual
before starting your machine.
• Respect all the safety standards before running the equipment.
• Use the equipment only for the applications specied in the manual.
• Always remain alert when using the equipment.
• Transport the machine using the handles or the appropriate grips.
• During the breaks, remember to turn off the machine.
• Let at least 50 cm of free space between the equipment and any obstacle so that the air ow
is not blocked.
• Know how to quickly stop the equipment in case of necessity.
• Never use the equipment while it is running abnormally or it is defective.
• Do not direct a water jet or ammable liquid on the machine.
• Never direct an air jet or product jet on a person or an animal.
• Do not touch warm surfaces of the equipment.
• Never touch moving parts.
• Do not insert any object or the hands inside the protection grids to avoid any accident or
damage to the machine.
• For any outside job, only use appropriate extension cords.
• Always wear adequate body protections (glasses, gloves, overall and mask) and pay attention
to long hair.
• Maintain the equipment carefully and clean it properly after every use.
• Avoid absolutely to unscrew any connection while the machine is under pressure.
• Check the damaged parts.
• Do not clean the plastic parts with solvant.
• In case of needed After-Sale Service, always specify the machine model and its serial number.
• For any replacement of parts, only use genuine parts.
• Do not modify the machine.
• Do not cut or dismantle the protection grids.

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P5
2. WARNING (continued)
2.1. SAFETY (continued)
WORKSPACE
• Maintain the workspace clean and clear.
• Ambient operating temperature must be from 5°C and 35°C.
• Do not use the equipment in a potentially explosive area.
• Do not place any potentially inammable objects in close proximity to the machine.
• Take away every not qualied person from the working area of the machine, as well as children and
animals.
• In case of installation of the machine on scaffolding or a plan above ground level, attach the machine
to avoid any fall while operating.
• Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.
• Do not use in a conned space.
HOSES
• Always use hoses and connections adapted to the used product (genuine parts), do not try to x it.
• Do not walk on the hoses, do not bend them.
• Do not use the hoses to pull the machine.
• Do not use the hoses for other materials, especially at higher pressures.
STORAGE
• Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.
THERMAL ENGINE
BATTERY
The machine must not be stored in an area with a temperature lower than 0°C, otherwise
the water remaining in the pump may freeze.
IN CASE OF NECESSITY, WE SAVE OURSELVES THE RIGHT TO MAKE ANY USEFUL
MODIFICATION WITHOUT ADVANCED NOTICE.
In case of contact with eyes, rinse
immediately.
Consult an ophthalmologist.
Contains sulphuric acid.
Risk of chemical skin burns and corrosion.
Starting the engine produces sparks. The sparks can ignite nearby ammable gases. This
could cause an explosion or re.
TOXIC GAS RISK. The engine exhaust contains carbon monoxide, a poisonous gas that could
kill you in a matter of minutes. It is INVISIBLE and ODOURLESS. Even if you do not inhale
exhaust, you are still at risk of breathing in carbon monoxide. If you begin to feel ill, dizzy
or faint when using this machine, turn the engine off and get fresh air IMMEDIATELY. Seek
medical attention. You may be suffering from carbon monoxide poisoning.

User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP6
2. WARNING (continued)
2.2. END OF LIFE OF THE PRODUCT
At its end-of-life, the machine must not be eliminated with the other household waste. The
uncontrolled elimination of waste can harm the environment or human health. Individuals are
invited to contact the distributor which sold them the product or to inquire with their city hall
to know where and how to get rid of the product so it can be recycled while respecting the
environment.
For any further information, please contact our hotline to [e-mail] or
[phone].

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P7
3. YOUR MACHINE
3.1. DESCRIPTION
EUROPROLAV 15-200 TH is a robust washer, suitable for semi-intensive use on all types of jobs.
With its diesel engine, it is ideal for outdoor work. It is also equipped with a battery for electric starting.
3.2. TECHNICAL CHARACTERISTICS
Variable pressure 0 to 200 bar
Flow-rate 15 L/min
Nozzle 15°- 45
Motor power KOHLER 10 HP
Fuel used Diesel
Tank capacity 4,3 L
Lubrication splashing
Pump brass head, 3 ceramic pistons
Detergent suction system yes
Pump rotation 3400 RPM
Max. water temperature accepted 70°C
Lance double with KW coupling
Hose 20 m - 315 bar
Dimensions (L x w x h) 66 x 62 x 91 cm
Weight 120 kg
Delivered with
- a 20 m high pressure hose
- a 10 m water supply hose
- a 600 mm double lance

B
D
E
K
A
C
G
H
I
JL
NM
F
User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP8
3. YOUR MACHINE (continued)
3.3. IDENTIFICATION OF THE COMPONENTS
AWater supply hose HHigh pressure outlet connection
BLance IWater inlet quick coupler
CEngine JOil level cap
DHigh pressure hose KBattery
EPump LFuel tank lling cap
FBy-pass MEngine launcher
GManometer NContact key

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P9
4. USE OF THE MACHINE
4.1. PREREQUISITES
• The connection to the water supply must be made on an inlet with a sufcient ow rate, with a minimum
Ø19 hose to be connected to the pump’s quick coupling.
• The high pressure hose is connected to the connection at the pump by-pass outlet.
• The engine must be stopped when lling the fuel tank.
• Never operate the washer without a water supply, as this could cause serious damage to the pump.
• The temperature of the water used must not exceed +60°C.
Before each use of the washer, check the engine and pump oil levels using the dipsticks
intended for this purpose.
Do not use the washer in a closed room or in an area where the temperature is below 0°C.

User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP10
4. USE OF THE MACHINE (continued)
4.2. STARTING UP
1. Check the oil level.
2. After connecting the washer to the water supply, open the water supply completely.
3. Press the trigger on the lance, water will come out of the nozzle at low pressure.
4. Make sure the tank contains fuel.
5. Put the accelerator on full throttle.
6. Start the engine by pulling on the launcher (or turning the contact key), with the trigger held in.
7. Release the trigger and let the engine warm up for a few moments.
8. The cleaner is ready for use. To adjust the working pressure, turn the black knob on the by-pass and
check the pressure set on the manometer.
ENGINE SHUTDOWN
Turn the key to the OFF position.
After each engine shutdown, it is important to relieve the pressure remaining in the hose. To
do this, press the trigger on of the lance.

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P11
5. DEFECTS AND REMEDIES
Defect To check Remedy
Abnormal pressure oscillations
• The pump sucks air. • Check the suction hoses.
• Water supply lter worn, dirty
or clogged. • Clean or change the lter.
The pump operates without
reaching the required pressure
• Unsuitable or worn nozzle. • Change the nozzle.
• Worn gaskets. • Change the gaskets.
Pressure drops
• Worn nozzle. • Change the nozzle.
• Worn valve. • Change the valve.
• Dirty water supply lter. • Clean or change the lter.
• Adjustment by-pass worn or
clogged. • Clean or change the by-pass.
• Worn gaskets. • Change the gaskets.
Abnormal noise
• Air suction. • Check the suction hoses.
• Worn or dirty bypass. • Clean or change the by-pass.
• Worn bearings. • Change the bearings.
Oil leaks • Worn oil gaskets. • Change gasket kit.
Water in oil • Worn oil or water gaskets. • Change gasket kit.
Water leakage from the lance • Worn seals. • Change gasket kit.
In case of an unknown defect or a doubt on the good running of the machine, do not try to
repair it by yourself or to dismantle it.
Contact an authorized After-Sale Service or our hotline : [phone].
Before loosening the hose, make sure it is no longer under pressure.

User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP12

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P13
6. DECLARATION OF CONFORMITY
THE MANUFACTURER : EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET
DECLARES THAT THE EQUIPMENT DESIGNATED BELOW :
Trademark: EUROPE PROJECTION
Type: Thermal High Pressure Washer
Model: EUROPROLAV 15-200 TH Diesel
COMPLIES WITH THE THE DIRECTIVES:
• Machines 2006/42/CE
• CEM 2014/30/UE
• ROHS 2011/65/UE
• Noise emissions 2005/88/CE
ROUSSET, JANUARY 20th 2021
Patrick BOREL
President
EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET
Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510

User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP14
7. WARRANTY CONDITIONS
Each equipment is delivered inspected and tested.
We exclude any warranty for visible defects, not notied by the customer within 48 hours.
The equipment sold is guaranteed during the manufacturer’s warranty from the date of purchase, as
specied on the original proof of purchase, and under the conditions dened by the manufacturer.
This warranty covers any equipment against any manufacturing or material defect, under normal conditions
of use. Insofar as the customer is presumed to be a professional of the same eld of specialty, this warranty
covers only the defect of conception of the equipment rendering it unt for its use, which could not be
detected by a professional buyer.
The defects or deteriorations caused by natural wear, external accident or a modication, use, storage or
treatment of the equipment not planned by the manufacturer, nor specied by ourselves, are excluded from
any warranty.
Are expressly excluded from the warranty the defects resulting from an improper use, the application of
abrasive or corrosive products, an inappropriate installation, the negligence, an insufcient maintenance
or cleaning, inappropriate conditions of storage, chemical, electronical or electric inuences, any change
in the normal process of use.
The following wearing parts are not covered by the warranty (non-exhaustive list): rotors, stators, driving
shafts, connecting rods, seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston
rods, prime/spray valve assy, seal kits, membranes, suction and delivery valves, carding machine vanes,
lters, oils, chains and quick-release clip.
The warranty also excludes the equipment on which the serial number was erased or made illegible, on
which unauthorized people made attempts of repair, which were totally or partially dismantled.
The manufacturer’s warranty shall always be subject to the presentation of the purchase invoice.
If the defective equipment is covered by the manufacturer’s warranty, it shall be repaired or replaced at our
discretion free of charge.
If the defective equipment is not covered by the manufacturer’s warranty, we shall issue a quote for the
repair that we shall submit to the customer for approval.
Except as otherwise required by law, this manufacturer’s warranty is exclusive of all other warranties,
including the statutory warranty of hidden defects.
In case of intervention of our services on a breakdown caused by the customer or an incident excluded in
the conditions referred to above, the costs of repair and transport shall be invoiced to the customer.
We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of
income, turnover, loss of prots, loss of image, of any kind whatever.
Our equipment are covered by a manufacturer’s warranty (parts and labor) of 12 months following
the purchase date by the nal customer, without exceeding 24 months from the date of purchase by
the client. The nal user can extend this manufacturer’s warranty for a further 12 months by lling
in the warranty extension form on our website www.euromair.com (under After-Sale Service) within
4 weeks of purchase.
This manufacturer’s warranty and its extension shall automatically cease if the customer does not
resell the equipment within 24 months of its purchase. The cases of exclusion of warranty mentioned
in articles above are also applicable to our own equipment.

202107-540A-ENG User manual - EUROPROLAV 15-200 TH Diesel P15
7. WARRANTY CONDITIONS (continued)
In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment.
Any legal action of the customer against us relating to the warranty of the equipment shall be barred 1 year
after the date of discovery of the defect. The customer shall have to prove the date of this discovery.
Request for Warranty
For any request related to the repair of an equipment covered by the manufacturer’s warranty, the customer
shall have to ll the warranty form, available on our website to the following address: https://www.euromair.
com/en/after-sales-service/
For a full dossier, the following documents shall have to be attached:
• the purchase invoice of the nal user
• pictures of the defective parts of the equipment
• a description of the breakdown
• the quote of labor if the customer is certied by EUROMAIR for repairing the equipment
No invoice of labor shall be taken into account without our prior approval.
Analysis of the breakdown by our technical department
A le number shall be given to the customer and an answer shall be provided within 48 working hours after
reception, provided that the request for warranty is considered as full.
In the event the equipment is covered by the manufacturer’s warranty, we shall conrm the warranty to
the customer and send him a quote (without price) detailing the parts to be changed and any comments.
Return of replacement parts
Replacement parts must be ordered with a warranty agreement number and will be made available to the
customer at our factory.
The conditions of return of the equipment are detailed in our Delivery terms.
In the case of a warranty claim on an on-board component such as a Kohler, Honda or Vanguard engine in
a machine manufactured by us, only the manufacturer of the component is able to validate the warranty
coverage.
In this case, the request must be addressed directly to the manufacturer of the component or to its nearest
authorised representative. The Euromair, Euromair MPC or Mixer service centres may be considered as the
manufacturer’s representatives if they are the closest. As this principle also applies to batteries, our supplier
Parts Holding Europe, or one of its sister companies, remains your contact for your requests (https://www.
partsholdingeurope.com/).

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510
User manual - EUROPROLAV 15-200 TH Diesel 202107-540A-ENGP16
More information on www.euromair.com