EUROPRO EUROPROLAV 15-200 TH.2 User manual

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510
EUROPROLAV 15-200, 15-250, 18-280 TH.2
User manual
Edition of 25/06/2020

User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 202006-445-ENGP2
You just acquired one of our
machines and all the team
of Europe Projection thanks
you for the condence
you have granted us.
Manufacturer of professional
equipments for paint and
llers, we have put our
know-how for 25 years
at the service of the
users of our machines.
Our technical & commercial
team is at your disposal
for any further information
you may need about the
machine you just acquired.
EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET
Tél : [phone]
Fax : [phone]
SUMMARY
1. USER MANUAL............................................................. p. 3
1.1. Importance of the manual .........................................p. 3
1.2. Receivers of the manual............................................p. 3
2. WARNING .................................................................... p. 4
2.1. Safety .....................................................................p. 4
2.2. End-of-life of the product ..........................................p. 5
3. YOUR MACHINE ........................................................... p. 6
3.1. Description..............................................................p. 6
3.2. Technical characteristics ...........................................p. 6
3.3. Identication of the components ................................p. 7
4. USE OF THE MACHINE ................................................. p. 8
4.1. Prerequisites............................................................p. 8
4.2. Starting up ..............................................................p. 8
5. DEFECTS AND REMEDIES............................................. p. 9
6. DECLARATION OF CONFORMITY ................................... p.10
7. WARRANTY CONDITIONS.............................................. p.11

202006-445-ENG User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 P3
1. USER MANUAL
1.1. IMPORTANCE OF THE MANUAL
This manual is a key part for the use of your machine. It summarizes the procedures of starting-up, cleaning
and maintenance of the device and also the safety instructions you need to observe.
Read carefully all the working and safety instructions and the warnings included in this manual before
starting your machine.
Most of the accidents are caused by the non-compliance of the safety standards and rules.
This manual must be kept near the machine, within reach of the user and held in good condition until the
nal destruction of the machine.
In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page
4 for a copy at any moment.
1.2. RECEIVERS OF THE MANUAL
This manual is intended to any staff which will manipulate the machine :
- people in charge of the transport of the machine
- people in charge of the use of the machine
- people in charge of the cleaning and maintenance of the machine
- people in charge of the nal destruction of the machine

User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 202006-445-ENGP4
2. WARNING
2.1. SAFETY
Using the machine in an incorrect way or in non-compliance of the safety instructions indicated in
this manual can cause death or serious injuries.
Read carefully all the working and safety instructions and the warnings contained in this manual
before starting your machine.
• Respect all the safety standards before running the equipment.
• Use the equipment only for the applications specied in the manual.
• Always remain alert when using the equipment.
• Transport the machine using the handles or the appropriate grips.
• During the breaks, remember to turn off the machine.
• Let at least 50 cm of free space between the equipment and any obstacle so that the air ow
is not blocked.
• Know how to quickly stop the equipment in case of necessity.
• Never use the equipment while it is running abnormally or it is defective.
• Do not direct a water jet or ammable liquid on the machine.
• Never direct an air jet or product jet on a person or an animal.
• Do not touch warm surfaces of the equipment.
• Always wear adequate body protections (glasses, gloves, overall and mask) and pay attention
to long hair.
• Never touch moving parts.
• Do not insert any object or the hands inside the protection grids to avoid any accident or
damage to the machine.
• For any outside job, only use appropriate extension cords.
• Maintain the equipment carefully and clean it properly after every use.
• Avoid absolutely to unscrew any connection while the machine is under pressure.
• Check the damaged parts.
• Do not clean the plastic parts with solvant.
• In case of needed After-Sale Service, always specify the machine model and its serial number.
• For any replacement of parts, only use genuine parts.
• Do not modify the machine.
• Do not cut or dismantle the protection grids.

202006-445-ENG User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 P5
IN CASE OF NECESSITY, WE SAVE OURSELVES THE RIGHT TO MAKE ANY USEFUL
MODIFICATION WITHOUT ADVANCED NOTICE.
2. WARNING (continued)
2.1. SAFETY (continued)
WORKSPACE
• Maintain the workspace clean and clear.
• Ambient operating temperature must be from 5°C and 35°C.
• Do not use the equipment in a potentially explosive area.
• Do not place any potentially inammable objects in close proximity to the machine.
• Take away every not qualied person from the working area of the machine, as well as children and
animals.
• In case of installation of the machine on scaffolding or a plan above ground level, attach the machine
to avoid any fall while operating.
• Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.
HOSES
• Always use hoses and connectors (original parts) with appropriate maximum pressure characteristics,
do not attempt to repair them.
• Do not walk on the hoses, do not bend them.
• Do not use the hoses to pull the machine.
STORAGE
• Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.
2.2. END OF LIFE OF THE PRODUCT
At its end-of-life, the machine must not be eliminated with the other household waste. The
uncontrolled elimination of waste can harm the environment or human health. Individuals are
invited to contact the distributor which sold them the product or to inquire with their city hall
to know where and how to get rid of the product so it can be recycled while respecting the
environment.
For any further information, please contact our hotline to [e-mail] or
[phone].
The machine must not be stored in an area with a temperature lower than 0°C, otherwise
the water remaining in the pump may freeze.

User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 202006-445-ENGP6
3. YOUR MACHINE
3.1. DESCRIPTION
EUROPROLAV washers are powerful and robust washers. They are suitable for use on any type of job.
They are equipped with places to roll up the water inlet and lance hoses. With large diameter wheels and
a reinforced chassis, they are very manoeuvrable and designed for easy maintenance.
The 15-200 TH.2 model is also equipped with detergent suction.
3.2. TECHNICAL CHARACTERISTICS
15-200 TH
Kohler
15-200 TH
Honda
15-250 TH
Honda
18-280 TH
Honda
Variable pressure 0 to 200 bar 0 to 250 bar 0 to 280 bar
Flow-rate 15 L/min 18 L/min
Nozzle 15°- 45 15°- 40 15°- 40
Motor power KOHLER 9,5 HP HONDA 13 HP
Fuel used unleaded 98
Tank capacity 7,3 L 7,9 L
Consumption 2,2 L/h 3,4 L/h 3,78 L/h
Lubrication splashing
Pump brass head, 3 ceramic pistons
Detergent suction system yes no
Pump rotation 3400 RPM 3600 RPM 1450 RPM
Max. water temperature 70°C
Lance double with KW coupling
Hose 10 m - 315 bar 20 m - 315 bar
Dimensions (L x w x h) 66 x 62 x 91 cm
Weight 66 kg 68 kg 77 kg 79 kg

B
D
E
A
C
G
H
I
J F
202006-445-ENG User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 P7
3. YOUR MACHINE (continued)
3.3. IDENTIFICATION OF THE COMPONENTS
AWater supply hose
BLance
CEngine
DHigh pressure hose
EPump
FBy-pass
GManometer
HHigh pressure outlet connection
IWater inlet quick coupler
JOil level cap

User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 202006-445-ENGP8
4. USE OF THE MACHINE
4.1. PREREQUISITES
• The connection to the water supply must be made on an inlet with a sufcient ow rate, with a minimum
Ø19 hose to be connected to the pump’s quick coupling.
• The high pressure hose is connected to the connection at the pump by-pass outlet.
• The engine must be stopped when lling the fuel tank.
• Never operate the washer without a water supply, as this could cause serious damage to the pump.
• The temperature of the water used must not exceed +60°C.
4.2. STARTING UP
1. Check the oil level and then turn the engine button to the ON position.
2. After connecting the washer to the water supply, open the water supply completely.
3. Press the trigger on the lance, water will come out of the nozzle at low pressure.
4. After making sure the tank contains gasoline, open the fuel supply.
5. Engage the starter.
6. Put the accelerator on full throttle.
7. Start the engine by pulling on the starter, with the trigger held in.
8. Release the trigger and let the engine warm up for a few moments.
9. Turn the starter off.
10. The cleaner is ready for use. To adjust the working pressure, turn the black knob on the by-pass and
check the pressure set on the manometer.
ENGINE SHUTDOWN
Turn the button to the OFF position and shut off the fuel supply.
Before each use of the washer, check the engine and pump oil levels using the dipsticks
intended for this purpose.
Do not use the washer in a closed room or in an area where the temperature is below 0°C.
After each engine shutdown, it is important to relieve the pressure remaining in the hose. To
do this, press the trigger on of the lance.

202006-445-ENG User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 P9
5. DEFECTS AND REMEDIES
Defect To check Remedy
Abnormal pressure oscillations
• The pump sucks air. • Check the suction hoses.
• Water supply lter worn, dirty
or clogged. • Clean or change the lter.
The pump operates without
reaching the required pressure
• Unsuitable or worn nozzle. • Change the nozzle.
• Worn gaskets. • Change the gaskets.
Pressure drops
• Worn nozzle. • Change the nozzle.
• Worn valve. • Change the valve.
• Dirty water supply lter. • Clean or change the lter.
• Adjustment by-pass worn or
clogged. • Clean or change the by-pass.
• Worn gaskets. • Change the gaskets.
Abnormal noise
• Air suction. • Check the suction hoses.
• Worn or dirty bypass. • Clean or change the by-pass.
• Worn bearings. • Change the bearings.
Oil leaks • Worn oil gaskets. • Change gasket kit.
Water in oil • Worn oil or water gaskets. • Change gasket kit.
Water leakage from the lance • Worn seals. • Change gasket kit.
In case of an unknown defect or a doubt on the good running of the machine, do not try to
repair it by yourself or to dismantle it.
Contact an authorized After-Sale Service or our hotline : [phone].
Before loosening the hose, make sure it is no longer under pressure.

User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 202006-445-ENGP10
6. DECLARATION OF CONFORMITY
THE MANUFACTURER : EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET
DECLARES THAT THE EQUIPMENT DESIGNATED BELOW :
Trademark : EUROPE PROJECTION
Type : Thermal High Pressure Washer
Model : EUROPROLAV 15-200 TH.2 / 15-250 TH.2 / 18-280 TH.2
COMPLIES WITH THE ARTICLE:
• the R.233-73 article of the Labour Code
THE DIRECTIVES :
• Machines 2006/42/CE
• CEM 2014/30/UE
• ROHS 2011/65/UE
• Noise emissions 2005/88/CE
AND WITH THE STANDARDS:
• NF EN ISO 12100
• NF EN 1829-1
• NF EN 1829-2
ROUSSET, JANUARY 20th 2020
Patrick BOREL
President
EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET
Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510

202006-445-ENG User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 P11
Our equipments are covered by a warranty (parts and labour) of 12 months following the purchase.
The duration of this warranty can be extended by 6 months by completing the warranty extension
form within 4 weeks after purchasing on our website www.euromair.com (section Warranty).
7. WARRANTY CONDITIONS
Each product is delivered inspected and tested.
We exclude any warranty for visible defects for which the customer did not claim within 48 hours.
The equipments sold are covered by the warranty during the period dened by the manufacturer from
the date of purchase, the date on the original proof of purchase being authentic and under the conditions
dened by the manufacturer.
This warranty covers any equipment against any manufacturing or material defect of for normal use and
service. Insofar as the customer is presumed to be a professional of the same specialty, the guarantee
covers only the lack of realization of the equipment rendering it unt for its use not likely to be detected by
a professional buyer.
The defects or deteriorations caused by natural wear, external accident or a modication, use, storage or
treatment of equipments not planned by the manufacturer, nor specied by ourselves, are excluded from
any warranty.
Are expressly excluded from the warranty the defects coming from: a bad use, the application of abrasive
or corrosive products, an inappropriate installation, the negligence, an insufcient maintenance or cleaning
chemical, electrochemical or electric inuences, any change in the normal process of use.
The following wearing parts are not covered by the warranty: rotors, stators, driving shafts, connecting rods,
seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston rods, prime/spray valve
assy, seal kits, membranes, suction and delivery valves, carding machine vanes, lters, oils.
The warranty also excludes the equipments: on which the serial number was erased or made illegible, on
which unauthorized people made attempts of repair which were totally or partially dismantled.
Defective equipment will be removed by us. Any shipment of equipment by the customer will be at its own
expense. The guarantee will be subject to the presentation of the purchase invoice. We will then be able to
perform an equipment analysis to determine if the defect is covered by the warranty.
If the defective equipment is covered by the warranty, it will be repaired or replaced free of charge. Repaired
equipment (under warranty) will be delivered to the customer free of charge.
If the defective equipment is not covered by the warranty, we will issue a quote for the repair that we will
submit to the customer’s agreement. The costs of removal and shipping of equipment not covered by the
warranty will be charged to the customer, whether or not the latter accepts the repair estimate.
Except as otherwise required by law, this warranty is exclusive of all other warranties, including the statutory
warranty of hidden defects.
In case of intervention of our services on a breakdown caused by the customer or an outage excluded in the
conditions referred to above, the costs of repair and transport will be billed to the customer.
We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of
income, turnover, loss of prots, loss of image, of any kind whatever.
In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment.
Any action of the customer against us relating to the guarantee of the equipments will be prescribed within
the period of 1 year as from the day of the discovery of the defect. It is up to the customer to prove the day
of this discovery.

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510
User manual - EUROPROLAV 15-200, 15-250, 18-280 TH.2 202006-445-ENGP12