Eurosep Instruments Q2L Series User manual

Spotlight Q2L Serie
LED Leaf Barndoor Projector
EUROSEP
Instruments
1. Important Points
1.1. The leaf barndoor projector must be installed in a compatible 2/3 circuit track adaptor, stable
and securely fastened, away from any source of heat or strong magnetic fields.
1.2. The 2/3 circuit track must be connected to a mains voltage between 2 -24 V / 5 -6 Hz. If
the leaf barndoor projector is permanently connected, it is advisable to install a switch or circuit
breaker in the vicinity.
1.3. Never operate the leaf barndoor projector when the installation instructions are not followed
(see paragraph 4).
1.4. Never disassemble the optical module nor
the 2/3 circuit track adaptor.
Before any handling or operation with the leaf barndoor projector, it is
essential to take note of the following points:
The LED Q2L series Leaf Barndoor projector has been
developed to meet the particular needs of museums and
architecture.
Ideal for replacing incandescent light sources, this range
of leaf barndoor projectors uses a 16W LED module with a
color temperature of 3 °K (warm white) and 4 °K
(neutral white), high intensity, with typical CRI (Ra) and
red rendering (R9) indexes of 95 and 9 respectively.
The luminous flux is manually adjustable from 2 to
1 %, the emitted intensity is equivalent to a light system
equipped with a 1 W halogen bulb.
 A filter placed at the light beam output provides a
"flood" spot whose the size can be adjusted by four leaf
barndoors.
The optical body, made of aluminum (black), allows an
efficient passive cooling without any need of a forced
cooling.
The light emitted from the LED module covers the
spectrum from 4 to 7 nm with no emission in the
ultraviolet nor in the infrared.
Power is supplied directly from the mains 23 V/5 Hz via a 2/3-circuit track adaptor.
The projector has a vertical adjustment range of 11 ° and a horizontal adjustment range of 36 ° in
azimuth.

1.5. Warning: This leaf barndoor projector is a Class A device. In a residential environment, this
device may cause low radio interferences. In this case, the user may be required to take
appropriate measures to remedy any potential interference.
1.6. Cleaning: The outside of the leaf barndoor projector can be cleaned with a non-corrosive
conventional cleaning product without spray and apply with a soft cloth. The cleaning must be
done light source off, the whole set back completely at room temperature.
2. Warranty Conditions
EUROSEP Instruments warrants the full system for a period of 2 years from the date of
delivery, when used strictly in accordance with the attached directives of use.
This warranty is strictly limited to repairing or replacing of the damaged product. To enjoy full
warranty, the purchaser commits himself to justify his demand by a written request. Also, he has
to give to EUROSEP Instruments all his support in order to notice and repair the damages. He
should avoid repairing the unit by himself or by someone else unless he got a written agreement
from EUROSEP Instruments.
All warranties are excluded for proximate, incidental or consequential damages, negligence, lack
of supervision or maintenance, use in non-conformity with the instruction manual directives and
replacement or repair due to a fair wear.
EUROSEP Instruments shall in no event be held liable for any damage caused by products supplied
by it.
Prior operation, it is essential to take note of the "Important Points" described in paragraph 1.
3. Description of the Leaf Barndoor Projector
The optical module and the 2/3 circuit track adaptor surfaces can be hot
during operation. Before undertaking any manipulation, wait for their
complete cooling.
Optical Module
2/3 Circuit Track Adaptor
Leaf Barndoor
M5 fixing screws
Light intensity
adjustment
System
to hang the
optical module
2 M5 butterfly screws

4. Operation
4.1. 2/3 circ it track adaptor installation
•Insert the 2 tooth lock washers on
the threated shaft of the optical module (1),
•Take the 2/3 circuit track module,
slightly spread the 2 arms of its
support and position each of them in
the threated shaft,
•Screw the 2 butterfly screws (2),
•Connect the cable on the rear part of the
optical module.
4.2. Installation into the 2/3 circ it track
•Slide the 2/3 circuit track module into a compatible
circuit track (3),
•Pull the trigger to fix the position (3),
•Turn the rotary knob to the correct
position to ignite (3).
4.3. L mino s intensity adj stment
•The potentiometer located on the 2/3
circuit track module allows the light
intensity to be adjusted between 2 and
1 % (3).
4.4. Leaf barndoor adj stment
•Manually adjust the leaf barndoor position (4).
5. Technical Characteristics
5.1. Main S pply
Main supply 2 - 24 VAC
Frequency 5 - 6 Hz
Number of phase 1
Input wattage From 5 à 2 W (depending of the
light intensity)
5.3. Optical
Bandwidth 4 à 7 nm
LED Wattage 16 W
CRI (Color Rendering Index) 95 typical
1
2
5.2. General
Operating temperature +1 / +4 °C
Max. relative humidity 95%
Protection indice IP2
Dimensions 15 x11 x26 mm
Poids total 1,2 kg
4
3
Trigger
Rotary knob
Potentiometer
Leaf b
arndoor
s

5.4. Range of Leaf Barndoor Projectors
* Light Intensity measured at 1m from the leaf barndoor projector.
Manufacturer Name EUROSEP Instruments
Address ZI STELYTEC
424 SAINT CHAMOND (France)
We, EUROSEP Instruments, declare under our sole responsibility that the products named here-after :
Product Description : LED LEAF BARNDOOR PROJECTOR
Part Number : PRSPQ2XXXL
comply with requirements of following European Directives :
RoHS Directive : 2 11/65/UE from 8/ 6/2 11
EMC Directive : 2 14/3 /UE from 26/ 2/2 14
Safety Directive : 2 14/35/UE from 26/ 2/2 14
Product’s compliance has been assessed in conformity with the relevant Union harmonization legislation,
by applying following standards :
Low Voltage Safety
EN 60598-1 (2015) + EN60598-2-1 (1991) + EN 60598-2-5 (2016)
Electromagnetic Emissions
EN 55015 (2014)
EN 61000-3-2 (2014) Classe A
EN 61000-3-3 (2014)
Electromagnetic Imm nity
EN 61000-4-2 (2009), 4-3 (2006 + A1-2008 + A2-2011), 4-4 (2013), 4-5 (2014),
4-6 (2014), 4-8 (2010), 4-11 (2004)
EN 61547 (2009)
Saint Chamond, October 1st, 2 17.
Thomas MONTICO
President
Non-binding document, subject to change without notice. All trademarks are the property of their respective manufacturer.
Copyright@ October 2 17 - EUROSEP Instruments – PRSPQ2L.D1.1A
Part Number Color Temp (°K) Lux/1m* Body Color
PRSPQ23L 3 45 Black
PRSPQ24L 4 5 Black
EU
DECLARATION
OF
CONFORMIT
Y
EUROSEP
Instruments
BP 38233 Cergy Saint Christophe
F-95800 Cergy Pontoise Cedex (Fran e)
Tél : [phone] - Fax : [phone]
E-mail : eurosep@eurosep. om - Internet http://www.eurosep. om