Chauvet WELL FIT User manual

User Manual

Edition Notes
WELL Fit User Manual Rev. 5
Edition
Notes
The WELL Fit User Manual Rev. 5 includes a description, safety precautions, and installation,
programming, operation, and maintenance instructions for the WELL Fit
as of the release date
of this edition in 2018.
Trademarks
CHAUVET, the Chauvet logo and WELL Fit are registered trademarks or trademarks of
Chauvet & Sons, LLC
. (d/b/a Chauvet and Chauvet Lighting) in the United States and other
countries. Other company and product names and logos referred to herein may be trademarks
of their respective companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text
and images are owned by Chauvet.
© Copyright 2019 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information
purposes only. Chauvet expressly prohibits the u
sage, copy, storage, distribution, modification,
or printing of this manual or its content for any ot
her purpose without written consent from
Chauvet.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended
Audience
Any person in charge of installing, operating, and/or maintaining this product should completely
read through the guide that shipped with the product, as well as this manual, before installing,
operating, or maintaining this product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects.
However, Chauvet assumes no responsibility and specifically disclaims any and all liability to
any party for any loss, damage or disruption ca
used by any errors or omissions in this
document, whether such errors or omissions result from negligence, accident or any other
cause. Chauvet reserves the right to revise the content of this document without any obligation
to notify any person or company of such revision, however, Chauvet has no obligation to make,
and does not commit to make, any such revisions..
Document
Revision
The WELL Fit User Manual Rev. 5 is the revised edition of this manual. Go to
www.chauvetprofessional.com for the latest version.

Table of Contents
WELL Fit User Manual Rev. 5 -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included.................................................................................................................................................... 1
Claims..................................................................................................................................................................................1
Manual Conventions.............................................................................................................................................................1
Symbols...............................................................................................................................................................................1
Safety Notes.......................................................................................................................................................... 2
Personal Safety....................................................................................................................................................................2
Mounting And Rigging...........................................................................................................................................................2
Power And Wiring.................................................................................................................................................................2
Operation.............................................................................................................................................................................2
Expected LED Lifespan.......................................................................................................................................... 2
2. Introduction...............................................................................................................................................3
Description............................................................................................................................................................. 3
Features ................................................................................................................................................................ 3
Well Fit Overview................................................................................................................................................... 4
Product Dimensions............................................................................................................................................... 5
Charging Case Dimensions (Not sold with the Single Fixture)................................................................................. 6
3. Setup..........................................................................................................................................................7
AC Power .............................................................................................................................................................. 7
AC Plug................................................................................................................................................................................7
Battery Charge Notes ...........................................................................................................................................................7
Replacing the Fuse...............................................................................................................................................................7
Power Linking.......................................................................................................................................................................7
DMX Linking .......................................................................................................................................................... 8
DMX Personalities................................................................................................................................................................8
Wireless Operation................................................................................................................................................. 8
Initial Setup ..........................................................................................................................................................................8
Configuration........................................................................................................................................................................8
Product Pairing.....................................................................................................................................................................8
Storage Notes ......................................................................................................................................................................8
W-DMX Setup ......................................................................................................................................................................9
IR Infrared Remote Control .................................................................................................................................... 9
IR Remote Operation............................................................................................................................................................9
Mounting...............................................................................................................................................................10
Orientation..........................................................................................................................................................................10
Rigging...............................................................................................................................................................................10
Procedure...........................................................................................................................................................................10
4. Operation.................................................................................................................................................11
Control Panel Description......................................................................................................................................11
Control Options.....................................................................................................................................................11
Programming........................................................................................................................................................11
Control Panel Lock................................................................................................................................................11
Passcode...........................................................................................................................................................................11
Menu Map.............................................................................................................................................................11
Menu Map (Cont.).................................................................................................................................................12
Configuration (Standalone)....................................................................................................................................13
Automatic Programs ...........................................................................................................................................................13
Fixed Static Color ...............................................................................................................................................................13
Manual Static Color.............................................................................................................................................................13
Dimmer Profiles..................................................................................................................................................................13
White Calibration ................................................................................................................................................................13
Backlight ............................................................................................................................................................................14
Software Information...........................................................................................................................................................14

Table of Contents
-ii- WELL Fit User Manual Rev. 5
Fixture Hours......................................................................................................................................................................14
LED Test............................................................................................................................................................................14
Factory Reset.....................................................................................................................................................................14
Configuration (DMX) .............................................................................................................................................14
DMX Personalities..............................................................................................................................................................14
DMX Control.......................................................................................................................................................................14
Wireless Settings................................................................................................................................................................14
IR Setting...........................................................................................................................................................................14
DMX Values..........................................................................................................................................................15
DMX Values (Cont.)..............................................................................................................................................16
5. Technical Information .............................................................................................................................17
Product Maintenance............................................................................................................................................17
6. Technical Specifications.........................................................................................................................18
Photometric Charts...............................................................................................................................................19
Returns ........................................................................................................................................................20
Contact Us....................................................................................................................................................21

Before You Begin
WELL Fit User Manual Rev. 5 -1-
1. Before You Begin
What Is
Included
Pack
Single
•6 WELL Fit
•Neutrik powerCON power cord
•IR remote
•Charging case
•Quick Reference Guide
•1 WELL Fit
•IEC power cable
•IR remote
•Charging base
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the charging case to make sure all the
parts are in the package and are in good condition.
If the charging case
or the contents (the product and included accessories) appear damaged
from shipping or show signs of mishandling, notify the carrier immediately, not Chauvet. Fa
ilure
to report damage to the carrier immediately may invalidate your claim. In addition, keep the box
and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Manual
Conventions
Convention
Meaning
1–512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1–10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols
Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.

Before You Begin
-2- WELL Fit User Manual Rev. 5
Safety Notes
Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained Chauvet certified technicians. Do not open the
housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not operate the product in a sealed enclosure or in an area without air circulation.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting And
Rigging
•Do not submerge this product (IP65). Temporary outdoor operation is fine.
•CAUTION: When transferring product from extreme temperature environments, (e.g. cold
truck to warm humid ballroom) condensation may form on the internal electronics of the
product. To avoid causing a failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•Not for permanent outdoor installation in locations with extreme environmental conditions.
This includes, but is not limited to:
•Where the normal high or low temperatures of the location exceed the temperature
ranges in this manual.
•Locations that are prone to flooding or being buried in snow.
•Other areas where the product will be subject to extreme radiation or caustic
substances.
•Only use the retractable foot to tilt the product.
•Be sure retractable foot is closed completely before inserting into the charging case.
•Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable.
Power And
Wiring
•Always make sure you are connecting this product to the proper voltage in accordance with
the specifications in this manual or on the product’s specification label.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•DO NOT connect the charging case to a dimmer or rheostat.
•It is not recommended to close the road case cover while charging the battery
unless the procedure is monitored.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. Have the
damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Chauvet product requires service, contact Chauvet
Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, primarily due to heat. Packaged in clusters,
LEDs exhibit higher operating temperatures than in ideal, single-LED
conditions. For this
reason, using clustered LEDs at their fullest intensity significantly reduces the LEDs’ lifespan.
Under normal conditions, this lifespan can be 40,000 to 50,000 hours. If extending this lifespan
is vital, lower the operating temperature by improving the ventilation around the product and
reducing the ambient temperature to an optimal operating range. In addition, limiting the overall
projection intensity may also help to extend the LEDs’ lifespan.

Introduction
WELL Fit User Manual Rev. 5 -3-
2. Introduction
Description
The WELL Fit is a quick setup, high-powered LED up-lighter. This small battery powered accent
wash light comes in a reflective chrome housing designed to blend into any décor. WELL Fit can
be controlled wirelessly either by W-DMX or by the included IR remote. A
lternatively, it can be
controlled manually from the OLED display on the product.
Features
•3-, 4-, 6- or 10-channel quad-color LED wash product
•Operating modes:
•3-channel: HSI control
•3-channel: HSV control
•4-channel: RGBW
•6-channel: RGBW, dimmer, strobe
•10-channel: RGBW, dimmer, strobe, color macro/white balance, auto programs,
dimmer speed, auto speed
•A completely wireless IP 65 rated battery powered up-light with four high powered quad
colored RGBA LEDs that is controlled by W-DMX or IR remote.
•Chrome exterior for blending into its surroundings.
•Drop in case charging for easy storage and re-charging of the battery. (Not available with
Single Fixture)
•8 hours of operation at full and a quick 5 hours charging time for frequent use.
•Built in automated programs recallable by IR, WDMX or manually.
•Built in kickstand for positioning light where you need it.
•M12 threaded insert for easy clamp installation and a Kensington lock position for securing
your investment.

Introduction
-4- WELL Fit User Manual Rev. 5
Well Fit Overview
Bottom View
Top View
Side View
Power Switch
Control Panel
M12
Threaded
Mounting
Hole
Retractable Foot Release
Handle
Quad Color LED
Charging Socket
Retractable Foot
Front View
Rear View

Introduction
WELL Fit User Manual Rev. 5 -5-
Product Dimensions
7.95 in
202 mm
5.71 in
145 mm
7.01 in
178 mm
5.43 in
138 mm
5.43 in
138 mm

Introduction
-6- WELL Fit User Manual Rev. 5
Charging Case Dimensions (Not sold with the Single Fixture)
18.54 in
471 mm
18.03 in
458 mm
5.75 in
146 mm
10.28 in
261 mm
6.69 in
170 mm
4.02 in
102 mm
21.85 in
555 mm
18.58 in
472 mm
14.33 in
364 mm

Setup
WELL Fit User Manual Rev. 5 -7-
3. Setup
AC Power
Each WELL Fit has an auto-ranging battery charger inside the flight case that works with an
input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for the
WELL Fit, refer to the label affixed to the product. You can also refer to the
Technical
Specifications chart in this manual.
The listed current rating indicates the maximum current
draw during normal operation. For more information, you may download Sizing Circuit Breakers
from the Chauvet website: www.chauvetprofessional.com.
•Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The WELL Fit charging case comes with a power input cord terminated with a Neutrik
powerCON
A connector on one end and an Edison plug on the other end (U.S. market). If the
power input
cord that came with your product has no plug, or if you need to change the Edison
plug, use the table below to wire the new plug.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Battery Charge
Notes
This product is equipped with a built-in rechargeable lithium ion battery.
•Avoid depleting the battery below 10%.
•For best results, charge the battery in a temperature between 32 ºF (0 ºC), and
95 ºF (35 ºC).
•When charging the battery, keep the product at least 1 m from any open flame or hot plate.
•If the battery is completely discharged, the device cannot be turned on immediately when
the charger is connected. Allow a depleted battery to charge for a few minutes before
turning on the device.
•While charging, the device may heat up. This is normal and should not affect the device’s
lifespan or performance. If the battery gets hotter than usual, the charger may stop
charging.
•It is not recommended to close the road case cover while charging the battery unless
the procedure is monitored.
•Always charge the battery with the product in an upright position.
•Do not charge the battery for more than 24 hours.
Replacing the
Fuse
The WELL Fit has no external fuse. However, the charging case and/or the charging base come
with a replaceable fuse.
1. Disconnect this product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.
Power Linking
The WELL Fit charging case supports power linking. You can power link up to 3 products at
120 V, or up to 5 products at 208 V and 230 V.

Setup
-8- WELL Fit User Manual Rev. 5
DMX Linking
The WELL Fit will work with a DMX controller using a wireless DMX connection. If using other
DMX-compatible products with the WELL Fit, you can control each individually w
ith a single
DMX controller.
DMX
Personalities
The WELL Fit uses a wireless DMX data connection for the 4 Ch, 6 Ch, 10Ch, HSI and HSV
DMX personalities.
•Refer to the Introduction chapter for a brief description of each DMX personality.
•Refer to the Operation chapter to learn how to configure the WELL Fit to work in these
personalities.
•The DMX Values section provides you with detailed information regarding the DMX
personalities.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.
Wireless
Operation
In optimal conditions, the WELL Fit can operate up to 300 m (900 ft) away from the W-DMX
transmitter. The W-DMX receiver in the WELL Fit must be paired with the W-
DMX transmitter
for wireless operation.
Once a WDMX receiver has been linked to a specific WDMX transmitter, it will remain
linked to that specific transmitter until it is linked to a different one.
Initial Setup
1. Turn the W-DMX transmitter on.
2. Connect the W-DMX transmitter to a DMX controller.
3. Place the WELL Fit within 300 m from the W-DMX transmitter.
4. Disconnect any DMX cable from the WELL Fit.
5. Turn the WELL Fit on.
Configuration
1. From the WELL Fit’s control panel, go to DMX Address.
2. Select the start address, as with any other DMX compatible product.
3. Go to Wireless Setting > Receive.
4. Select On. (The Signal Strength Indicator will show a ?in front of the bars)
5. Press the reset button on the W-DMX transmitter. (The Signal Strength Indicator on the
WELL Fit will show a ϟin front of the bars for 3 seconds while a connection is established.)
Product Pairing
If the WELL Fit has already been paired with the W-DMX transmitter, the Signal Strength
Indicator in the middle of the LCD screen will show the strength of the signal. In this case, the
WELL Fit is ready to work in Wireless mode.
Pairing the WELL Fit and a new W-DMX transmitter:
1. From the WELL Fit’s control panel, go to Wireless Setting.
2. Select Reset. The Signal Strength Indicator on the WELL Fit will show a ?in front of the
bars.
3. From the W-DMX transmitter, press <RESET> (the Signal Indicator on the transmitter will
flash).
4. Once the transmitter has found the WELL Fit, the Signal indicator on the W-DMX
transmitter will illuminate solid.
5. The Signal Strength Indicator in the middle of the LCD screen on the WELL Fit
will show the
strength of the signal.
Storage Notes
•Store charged product(s) in a dry environment, away from direct sunlight.
•Charge or discharge the battery to approximately 50% of capacity before storage.
•Lithium-Ion batteries continue to slowly discharge (self-discharge) when not in use or while
in storage. Routinely check the battery’s charge status
•Store the battery at temperatures between 41 °F and 68 °F (5 °C and 20 °C).
•Always store the product in an upright position (≤ 10° tilt).
W-DMX operation can be interrupted or inhibited by liquid masses between the
transmitter and receiver such as water, snow, or people. For best results, keep the area
between the transmitter and receiver clear of any liquid mass.

Setup
WELL Fit User Manual Rev. 5 -9-
W-DMX Setup
IR Infrared
Remote Control
Infrared (IR) mode allows the product to be controlled with an infrared remote controller. The
IR remote
can remotely set the product to various modes; adjust the color, speed and
sensitivity; and set the strobe.
The WELL Fit is compatible with the included IR remote from Cha
uvet. To enable use with
the IR remote, follow the instructions below:
1. Go to IR Setting in the main level.
2. Select On to activate the IR Receiver.
It may be necessary to turn the product off and on again when switching from W-DMX
to IRC and vise-versa.
IR Remote Operation
Be sure the IR remote is pointing directly at the product and there is nothing in between the
remote and the product.
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
1. Press <AUTO> on the IR remote.
2. Press <+> or <–> to choose between the four different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IR remote.
2. Press <+> or <–> to either increase or decrease the speed of the program.
Manual Color Control
To choose a specific color with the IR remote:
3. Press <MANUAL> on the IR remote.
4. Press any number between <0> and <9> to choose your color.
To manually control the RGBA percentage:
1. Press <MANUAL> on the IR remote.
2. Press <R>, <G>, <B>, or <A> (red, green, blue, or amber) to choose your color.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IR remote.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To choose a fade auto program:
•Press <FADE> repeatedly on the IR remote to choose between the two auto program
fade options
To black out the lights:
•Press <BLACK OUT> on the IR remote. This will turn off all the lights until the button is
pressed again.
To adjust the output level:
1. Press <%> on the IR remote.
2. Press <+> or <–> to increase or decrease the output level.
Note: The IR remote will not respond to any inputs when the Black Out mode is activated. If the remote does not
respond when a button is pressed, try pressing <BLACK OUT>. You may have inadvertently activated the Black
Out mode.
Control Panel
W-DMX Transmitter

Setup
-10- WELL Fit User Manual Rev. 5
Mounting
Before mounting this product, read and follow the Safety Notes. For our CHAUVET
Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
•When selecting an installation location, consider easy access to this product for operation,
programming adjustments, and routine maintenance.
•The product is not intended for permanent installation.
•Make sure to mount this product away from any flammable material as indicated in the
Safety Notes.
•If hanging this product, make sure that the mounting location can support the product’s
weight. See the Technical Specifications for the weight-bearing requirements of this
product.
•When hanging this product, always secure to a fastening device using a safety cable. For
our CHAUVET Professional line of safety cables, go to http://trusst.com/products/.
Procedure
The WELL Fit comes with an M12 threaded mounting hole to which you can attach mounting
clamps for hanging.
When mounting the product overhead, always use a mounting clamp and
safety cable. Mount the product securely to a rigging point, such as a pipe or truss. When
ri
gging the product, you should use a mounting clamp of appropriate weight capacity. You must
supply your own mounting clamps. Use at least one mounting point per product.
For our
CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.
When mounting the product on the floor, make sure that the product and any cables are away
from people and vehicles.
Mounting Diagram
Floor Mounting
Overhead Mounting
M12 Threaded
Mounting Hole
Handle

Operation
WELL Fit User Manual Rev. 5 -11-
4. Operation
Control Panel
Description
Button
Function
<ON/OFF>
Turns product on/off
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently selected
value in to the current function
<UP>
Navigates upward through the menu list or increases the numeric
value when in a function
<DOWN>
Navigates downward through the menu list or decreases the numeric
value when in a function
Control
Options
Set the WELL Fit starting address in the 001–512
DMX range. This enables control of up to 51
products in the 10-channel 10Ch personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level
and a variable number of programming levels for each option.
•To go to the desired main level, press <MENU> repeatedly until the option shows on the
display. Press <ENTER> to select. This will take you to the first programming level for that
option.
•To select an option or value within the current programming level, press <UP> or <DOWN>
until the option shows on the display. Press <ENTER> to select. In this case, if there is
another programming level, you will see that first option, or you will see the selected value.
•Press <MENU> repeatedly to exit to the previous main level.
Control Panel
Lock
This setting enables you to activate or disable the control panel lock, which keeps non-
authorized personnel from changing the product’s settings.
1. Go to the Key Lock main level.
2. Select On or Off.
Passcode
After being prompted to enter the passcode:
•Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.
Menu Map
Main Level
Programming Levels
Description
Auto Show
Auto 1–5
Speed
0–100
Automatic programs and speed
Static
Fixed Color
R
Red
G
Green
B
Blue
A
Amber
GB
Green/Blue
RB
Red/Blue
RG
Red/Green
RGB
Red/Green/Blue
RA
Red/Amber
GA
Green/Amber
BA
Blue/Amber
RGA
Red/Green/Amber
RBA
Red/Blue/Amber
GBA
Green/Blue/Amber
RGBA
Red/Green/Blue/Amber
Manual
Color
R
Value 0–255 Combines red, green, blue, and amber to
make a custom color (0–100%)
G
B
A

Operation
-12- WELL Fit User Manual Rev. 5
Menu Map (Cont.)
Main Level
Programming Levels
Description
Dimmer Mode
Off
No dimmer
Dimmer 1–3
Dimming curves Dimmer 1 (fast) to Dimmer 3
(slow)
Back Light
10S
Turns off display backlight after 10 sec of
inactivity
20S
Turns off display backlight after 20 sec of
inactivity
30S
Turns off display backlight after 30 sec of
inactivity
On
Display backlight always on
Information
Test
Turns on all LEDs in sequence for testing
Fixture Hours
Shows total product hours
Version
Shows installed software version
DMX Address 001–512
Selects DMX address (highest channel
restricted to personality chosen)
DMX Channel
4 Ch
4-channel: RGBA control
6 Ch
6-channel: RGBA control, dimmer, and strobe
10Ch
10-channel: RGBA control, dimmer, strobe,
color macro/white balance, auto programs,
auto speed, dimmer speed
HSV
3-channel: HSV control
HSI
3-channel: HSI control
Master/Slave Mode
Master
Reserved for future use
Slave
White Balance Balance
R
Value 125–255
Sets red LED maximum value
G
Sets green LED maximum value
B
Sets blue LED maximum value
Wireless Setting Receive
Off
Turns wireless DMX function off
On Reset
On
Resets the wireless setting
Off
IR Setting
On
Activates/deactivates IR receiver
Off
Key Lock
On
Turns the passcode on or off
Off
Factory Reset
On
Resets to factory defaults
Off

Operation
WELL Fit User Manual Rev. 5 -13-
Configuration
(Standalone)
Use standalone configuration to operate the product without a DMX controller.
Automatic
Programs
Automatic programs allow for dynamic RGBA color mixing without a DMX controller.
1. Go to the Auto Show main level.
2. Select the desired automatic (Auto 1–5) program.
3. Go to the Speed programming level.
4. Select the desired speed 0–100.
You cannot edit any of the automatic programs (Auto 1–5).
Fixed Static
Color
The fixed static color mode allows for preset RGBW color mixing without a DMX controller.
1. Go to the Static main level.
2. Select the Fixed Color programming level.
3. Select the desired color combination. See Menu Map.
Manual Static
Color
The manual static color mode allows for manually customizable RGBA color mixing without a
DMX controller.
1. Go to the Static main level.
2. Select the Manual Color programming level.
3. Select the desired color R, G, Bor A.
4. Go to the Value programming option.
5. Select the desired color value 0–255 (0–100%).
6. Repeat for the other colors.
Dimmer Profiles
This setting determines how fast the output of the WELL Fit changes when you modify the
values of the red, green, blue, white, and dimmer faders. This setting provides three different
options to simulate the dimming curve of an incandescent lighting product.
1. Go to the Dimmer Mode main level.
2. Select a dimmer profile (Off, Dimmer 1, Dimmer 2, or Dimmer 3).
OFF:
The output is proportional (linear) to the dimmer and RGBW channel values.
Dimmer 1–3:
The output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, Dimmer 1 being the fastest and Dimmer 3 the
slowest.
White Calibration
This setting allows you to select the white color shown by the WELL Fit when the DMX
controller’s red, green, and blue faders are set to 255.
1. Go to the White Balance main level.
2. Go to Balance.
3. Select a color (R, G, or B).
4. Go to Value.
5. Select a color value (125–255).
6. Repeat for the other colors.
When selecting White Balance, you will only be able to define the values of red (R),
green (G), and blue (B).
The values of red (R), green (G), and b
lue (B) configured from White Balance will define
the color temperature shown when the RGB faders are set to 255.

Operation
-14- WELL Fit User Manual Rev. 5
Backlight
This setting allows you to set the amount of time the backlight on the
WELL Fit’s display stays on after the last button is pressed on the control panel.
1. Go to the BackLite main level.
2. Select On (remains on), 10S (10 seconds), 20S (20 seconds), or 30S (seconds).
Software
Information
This option shows what version of software the WELL Fit is running.
1. Go to the Information main level.
2. Select Version and the version number will show on the display.
Fixture Hours
This option shows the total amount of hours the WELL Fit has been turned on.
1. Go to the Information main level.
2. Select Fixture Hours and the total number of hours will show on the display.
LED Test
This option runs a check of the LEDs on the WELL Fit by turning on all the LEDs in sequence.
1. Go to the Information main level.
2. Select Test programming level.
Factory Reset
This option runs a check of the LEDs on the WELL Fit by turning on all the LEDs in sequence.
1. Go to the Factory Reset main level.
2. Select On to reset the product to factory settings.
Configuration
(DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX
Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the DMX Channel main level.
2. Select the desired personality (4 Ch, 6 Ch, 10Ch, HSI, or HSV).
•See the DMX Values section for the highest starting address you can select for each
personality.
•Make sure that the starting addresses on the various products do not overlap due to
the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All
products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the starting address:
a. Go to DMX Address main level.
b. Select the starting address (001–512).
The highest recommended starting address for each DMX mode is as follows:
DMX Personality
DMX Address
4 Ch
509
6 Ch
507
10Ch
503
HSI
510
HSV
510
Wireless Settings
This mode allows you to control DMX wirelessly. For detailed setup of this feature, see Wireless
Operation. To disable this feature:
1. Go to Wireless Setting > Receive.
2. Select Off.
Once a WDMX receiver has been linked to a specific WDMX transmitter, it will remain
linked to that specific transmitter until it is linked to a different one.
IR Setting
This mode allows you to control the WELL Fit with an IR remote. For detailed setup of this
feature, see IR Infrared Remote Control. To disable this feature:
1. Go to IR Setting.
2. Select Off.

Operation
WELL Fit User Manual Rev. 5 -15-
DMX Values
10Ch
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000 ó255
0–100%
5
Amber
000 ó255
0–100%
6 Strobe
000
ó
010
011 ó255
No function
Slow to fast
7 Color Macro + White
Balance
000 ó010
011 ó030
031 ó050
051 ó070
071 ó090
091 ó110
111 ó130
131 ó150
151 ó170
171 ó200
201 ó205
206 ó210
211 ó215
216 ó220
221 ó225
226 ó230
231 ó235
236 ó240
241 ó245
246 ó250
251 ó255
No function
R: 100% G: 0–100% B: 0
R: 100%–0 G: 100% B: 0
R: 0 G: 100% B: 0–100%
R: 0 G: 100%–0 B: 100%
R: 0–100% G: 0 B: 100%
R: 100% G: 0 B: 100%–0
R: 100% G: 0–100% B: 0–100%
R: 100%–0 G: 100%–0 B: 100%
R: 100% G: 100% B: 100% A: 100%
White 1
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
8 Auto Programs
000 ó051
052 ó101
102 ó152
153 ó203
204 ó254
255
No function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
9
Auto Speed
000 ó255
Slow to fast
10 Dimmer Speed
000 ó051
052 ó101
102 ó152
153 ó203
204 ó255
Preset dimmer speed from display menu
Linear dimmer
Nonlinear dimming curve 1 (fastest)
Nonlinear dimming curve 2
Nonlinear dimming curve 3 (slowest)

Operation
-16- WELL Fit User Manual Rev. 5
DMX Values (Cont.)
6 Ch
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000 ó255
0–100%
5
Amber
000 ó255
0–100%
6 Strobe
000
ó
010
011 ó255
No function
Slow to fast
4 Ch
Channel
Function
Value
Percent/Setting
1
Red
000 ó255
0–100%
2
Green
000 ó255
0–100%
3
Blue
000 ó255
0–100%
4
Amber
000 ó255
0–100%
HSV
Channel
Function
Value
Percent/Setting
1
Hue
000 ó255
0–100%
2
Saturation
000 ó255
0–100%
3
Value
000 ó255
0–100%
HSI
Channel
Function
Value
Percent/Setting
1
Hue
000 ó255
0–100%
2
Saturation
000 ó255
0–100%
3
Intensity
000 ó255
0–100%