Flash butrym LED Six Hole RGB User manual

USER MANUAL / INSTRUKCJA OBSŁUGI
Introduction
Thank you for purchasing LED Six Hole RGB. For safety reasons and to ensure the trouble-free operation,
carefully read the instructions.
1SAFETY INFORMATION
1. Installation should be done by qualified personnel in order to minimize the risk of accidental
electric shock
2. Disconnect the power supply before installation.
3. Before connecting the unit to the mains, make sure it is not damaged mechanically. If you
notice any signs of damage you should contact your dealer immediately. Do not connect the
device to the mains.
4. Do not use the device in high humidity conditions and at temperatures above 40° C
5. The device must be installed on stable structures
2PRODUCT INFORMATION
2.1 Specification
Power consumption: 20W
Power supply voltage: 250V
Voltage frequency: 50/60Hz
Diode type: 3in1
Number of diodes: 1
Display: LED - 4 characters
Color: RGB
Dimming: Linear: 0 - 100%
Number of DMX channels: 7
DMX standard: DMX 512
Control interface: 4 buttons
Operating modes: Auto, DMX, Sound control, Master/Slave
AC IN: IEC - C14
AC OUT: IEC - C13
DMX IN: XLR - 3 pin
DMX OUT: XLR - 3 pin:
Housing made: ABS
Height [cm]: 21
Width [cm]: 21
Depth [cm]: 17,5
Weight [kg]: 1,8
Weight with packaging [kg]: 2,6
Set includes: power cable, Mounting bracket
3INSTALLATION
After removing the packaging, check if the device was not damaged during transport. Before connecting to
the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage
caused by unstable mounting.

LED Six Hole RGB F7300236
www.flash-butrym.pl
1
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are
consistent with device requirements. All activities, including connecting the device to the mains must be
performed by qualified personnel.
4CONNECTIONS
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3-pin socket
2. Power (in/out): IEC-C14/IEC-C13
4.1 Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.
4.2 Voltage specification
Input Voltage
Total Power
Frequency
250V
20W
50/60Hz
4.3 Connecting power supply
The connection is performed using power cable with IEC-C14 connector (included).
The device must be operated by qualified personnel. Make sure that the power grid supply parameters are
consistent with device parameters and limitations are not exceeded.

www.flash-butrym.pl
2
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only
on the manufacturer or by a person with appropriate permissions.
5OPERATION MANUAL
5.1 Control panel
The control panel is equipped with display and 4 control buttons:
1. MENU –access to menu
2. UP –change value, go to previous option
3. DOWN –change value, go to next option
4. ENTER –confirm changes
5.2 Menu
Menu diagram:
–
Set DMX address
Auto red- Set speed (slow to fast)
Auto green- Set speed (slow to fast)
Auto blue- Set speed (slow to fast)
Single color jump change- Set speed
(slow to fast)
Double color jump change- Set speed
(slow to fast)
Triple color jump change- Set speed
(slow to fast)
Auto strobe- Set speed (slow to fast)
Sound control mode 1- Color fast
strobe
Sound control mode 2- Color jump
change

LED Six Hole RGB F7300236
www.flash-butrym.pl
3
5.3 DMX channel list
7CH mode
Channel
Function
Effect
CH 1
Dimmer
0-255: 0-100%
CH 2
Red
0-255: 0-100%
CH 3
Green
0-255: 0-100%
CH 4
Blue
0-255: 0-100%
CH 5
Strobe
0-9: No function
10-255: Strobe, fast to slow
CH 6
Motor movement
0-5: No function
6-127: Motor movement 1, slow to fast
128-255: Motor movement 2, fast to slow
CH 7
Auto
0-9: No function
10-255: Auto mode