Everlast 4264 User manual

PURE-TEC LIMITED
[email protected]
TEL.
TITLE PAGE
GENERAL INFORMATION 1
PACKING LIST & PARTS LIST 2
ASSEMBLY INSTRUCTIONS 3
ASSEMBLY DETAILS 4
HEAVY DUTY ADJUSTABLE
SPEED BAG PLATFORM
MODEL# 4264
TABLE OF CONTENTS
[phone]

WE WANT YO U T O KNO W T HAT EVERY PART H AS BEEN THOR OUG H LY IN SPEC TEDAND
DOUB LE-CHECKED T O ENSURE T R OUB L E-F REE ASSEMB LY. WALL MOUN TING H ARD WARE
IS NOT I NCL UDE D.
1. WALL MOUNTING HARDWARE IS NOT INCLUDED.
2. IT IS IMPORTANT THAT YOU FOLLOW ALL INSTRUCTIONS CAREFULLY.
3. AS YOU ASSEMBLE, BE SURE ALL HARDWARE IS SECURELY TIGHTENED. WHEN
INSTALLATION IS COMPLETE, MAKE SURE ALL PARTS ARE SNUG AND THAT THE ASSEMBLY
IS RIGIDLY ERECTED AND PROPERLY READY FOR USE.
4. IF AT ANY TIME YOU FIND ANY PART IS WORN, FATIGUED OR BECOMES DEFECTIVE,
CEASE USE OF THIS UNIT AND WRITE TO EVERLAST TO PROVIDE YOU WITH ANY REPLACE-
MENT PARTS AT A NOMINAL CHARGE.
WA RNI N G: FAILURE TO FOLLOW INSTRUCTIONS HEREIN MAY BE CAUSE FOR SERIOUS
INJURY. YOU ARE RESPONSIBLE FOR PROPER ASSEMBLY. THEREFORE, USERS OF THIS
PRODUCT MUST ASSUME ALL RISK OF INJURY.
GENERAL INSTRUCTIONS

PACK ING LI ST
STRINGERS
R.H. SLIDER BAR
L.H. SLIDER BAR
SLIDER TUBE WELDMENT
ADJUSTMENT SLIDER TUBE WELD-
MENT
SPEED BAG DRUM
SWIVEL W/ SCREWS
POLY BAG CONTAINING: ASSEMBLY
HARDWARE
PARTS LIST
STRINGER – R1
R.H. SLIDER BAR – R2
L.H. SLIDER BAR – R3
SLIDER TUBE WELDMENT – R4
ADJUSTMENT SLIDER TUBE WELD-
MENT – R5
QUICK RELEASE PIN – R6
LOCK KNOBS – R7
SWIVEL – R8
DRUM - R9

1. WALL MOUNTING HARDWARE IS NOT INCLUDED.
2. MOUNTING THIS PLATFORM IS A TWO-PERSON OPERATION.
3. DETERMINE THE MOUNTING HEIGHT AND DISTANCE FROM ADJACENT WALLS DESIRED, KEEPING IN MIND THIS
PLATFORM HAS 8” OF ADJUSTMENT. A ROUGH RULE OF THUMB IS, THE BOTTOM OF THE BAG YOU INTEND TO USE
SHOULD BE LEVEL WITH THE USER’S CHIN. BE SURE THE SELECTED LOCATION COINCIDES WITH STUDS IF YOU’RE
MOUNTING TO A WOOL STUD WALL. THIS UNIT IS DESIGNED FOR USE WITH STUDS ON 16” CENTERS.
4. ATTACH TOP STRINGER (R1) TO WALL AT DESIRED LOCATION. USE TWO 5/16” BAG SCREWS FOR WOOD STUD WALLS:
USE MASONRY ANCHORS FOR MASONRY WALLS. MOUNTING HARDWARE IS NOT PROVIDED. MOUNTING HOLES ARE TWO
OUTSIDE HOLES. SEE PAGE 5
5. LOOSELY ATTACH H.R. SLIDER BAR (R2) TO THE MOUNTED TOP STRINGER (R1) WITH M8X35 HEX HEAD BOLT.
LOOSELY ATTACH L.H. SLIDER BAR (R3) TO THE TOP STRINGER (R1).
6. PLACE BOTTOM STRINGER (R1) BETWEEN SLIDER BARS (R2 & R3) AND WALL AND ATTACH IT TO SLIDER BARS (R2 &
R3) AS IN STEP 5.
7. BE SURE SLIDER BARS (R2 & R3) HANG VERTICALLY AND BOTTOM STRINGER (R1) MOUNTING HOLES COINCIDE
WITH THE WALL STUDS, IF MOUNTING TO A STUD WALL; ATTACH THE BOTTOM STRINGER TO THE WALL AS IN STEP 4.
8. REMOVE SLIDER BARS (R2 & R3) FROM THE STRINGERS (R1).
9. SLIDE SLIDER TUBE WELDMENT (R4) OVER L.H. SLIDER BAR (R3) AND RE-ATTACH L.H. SLIDER BAR (R3) TO
STRINGERS, AND FASTEN SECURELY.
10. SLIDE ADJUSTMENT SLIDER TUBE WELDMENT (R5) OVER R.H. SLIDER BAR (R2) AND RE-ATTACH THE SLIDER BAR
(R2) TO THE STRINGERS, AND TIGHTEN THE BOLTS TO JUST SNUG.
11. MOVE BOTH SLIDE TUBE WELDMENTS (R4&R5) ALL THE WAY DOWN AGAINST THE BOTTOM STRINGER (R1).
12. ATTACH SWIVEL (R8) TO CENTER OF DRUM (R9)USING 4EA. M6X40 BOLTS AND M6 LOCK WASHERS AND NUTS
13. ATTACH THE DRUM (R9) TO SLIDER TUBE WELDMENTS (R4 & R5) USING USING 4EA. M8X35 BOLTS AND M8 LOCK
LOCKWASHERS AND NUTS ARE ON THE ANGLE IRON SIDE. THE BOLT GOES UP THROUGH THE PRE
ED HOLES IN THE DRUM (R9) FROM THE BOTTOM. TIGHTEN SECURELY.
14. HOLDING THE QUICK RELEASE PIN (R6) OUT MOVE THE DRUM (R9) AND SLIDER TUBES (R4 & R5) ALL THE WAY TO
THE TOP AND TIGHTEN THE R.H. SLIDER BAR (R2) BOLTS SECURELY. THE DRUM (R9) AND SLIDE TUBES (R4 & R5)
SHOULD SLIDE UP & DOWN THE SLIDER BARS (R2 & R3) SMOOTHLY. PLACE DRUM AT HEIGHT DESIRED AND ENGAGE THE
QUICK RELEASE PIN (R6).
15. THREAD FOUR HAND KNOBS (R7) INTO NUTS WELDED TO SLIDE TUBES (R4 &R5) AND TIGHTEN.
16. RECHECK ALL FASTENERS TO BE SURE THEY’RE ALL SECURELY TIGHTENED, HANG YOUR SPEED BAG, AND YOUR
PLATFORM IS READY FOR USE.
ASSEMBLY INSTRUCTIONS
MODEL # 4264 INSTRUCTIONS
WASHERS AND NUTS.
DRILL

ASSEMBLY DETAILS
R1
R3
R6
R7
R7
R8
R2
R4
R5
R9
Left
Top
Bottom
Front View
Right Side View
Right