Harrod Sport HOC-030 User manual

HOC-030
Folding Wheel Away Hockey Posts
INS589
Revision 2
©
30/01/2014
Harrod UK Limited
Code:
Product:
Pack Contents:
12x
2 2 x Right Hand Sideframe (
Backboards (FEQ426)
FEQ427)
3 2 x Left Hand Sideframe (FEQ428)
4 1 x Crossbar (Pair) (FEQ429)
1 x Fittings Pack (packed with crossbar) Containing:
5 4 x M10 Nyloc BZP (BOL202)
6 24 x Washer 21od10.5id x 2.5 thick (BOL721)
7 4 x Washer M10 Stainless Steel (BOL711)
8 2 x Net Clips (CLP040)
9 4 x M10 x 60 Hex Bolt (BOL300)
10 8 x M10 x 30 Hex Bolt (on crossbar) (BOL330)
11 12 x M6 x 25mm Eyebolt (BOL612)
Bolt Identification
TOOLS REQUIRED
2 x 17mm Spanner
1 x 13mm Spanner
1 x Step Ladder (optional)
IMPORTANT
Please read the assembly instructions carefully
before starting to assemble your goal
Brace Holes
View of Product
IMPORTANT
MUST
: All freestanding
goals be anchored at all times.
Please see additional general anchor
information sheet for assistance in
choosing the correct anchor option
for your goal or contact your
distributor for further advise.
Fig 1
APPROX ASSEMBLE TIME
2 People 10 Minutes Per Set.
3 People are required to move the goal.
Net Retaining
Rod
1
3
2
4
5
6
7
8
10
Sideframe Brace
9
10
10
11

HOC-030
Folding Wheel Away Hockey Posts
Code:
Product:
Assembly Instructions
Assembly Instructions
1: - Lay the crossbar on the ground
and position the uprights so that the sideframes are folded in to expose
the fixing holes as shown in fig 2. Insert the crossbar into uprights and
secure with the washer and bolts, and screw eyelets into place.
Fit the crossbar to the uprights
2: - Stand the goal upright, fold open the
sideframes, The backboard slots down between the sideboard and
back of the sideframe (as shown in fig 3) and is held in place with a
bracket at each end that hooks over a plate in the sideframe.
Fit the backboard
Fixing holes
6
10
Fig 3
Crossbar
Spigot
Fig 2

HOC-030
Folding Wheel Away Hockey Posts
Code:
Product:
Assembly Instructions
Assembly Instructions
Net
Retaining Rod
Fig 5
3: (supplied separately)
Remove the net retaining rods from the crossbar and
uprights by removing the nut from the end and sliding
the rods out of the eyebolts. (Note: crossbar retaining
bolts are within the fittings pack).
Position the net over the top of the sideframes and fit
to the crossbar by threading the net retaining rods
through the net and crossbar plates and secure with the
nut. Repeat this for the uprights (a step ladder may be
required).
Fitting the net
9
7
5
6
Side Frame
Support Brace
4: Identify the parts using the pack contents and fig 1.
Using a small set of step ladders/platfom assemble the
side frame using the parts listed above, then secure in the
location hole on the crossbar.
5:Moving the goal (3 adults are required to move the
goal). - In order to move the goal first remove the
backboard. Fold one sideframe in towards the goal by
removing the brace from the crossbar lug then fold the
sidefame. Insert the brace into the other lug on the crossbar
to secure the sideframe in the folded position.
Repeat for the other sideframe ensuring that the goal is
being supported at all times.
Lift the goal up onto the wheels by rotating the wheel arm
as shown in fig 6.
Hook the net up with the net clip to stop it from trailing on
the ground when the goal is being moved.
Before Fitting the Net - Make sure two or more people stretch the Net out into
shape as much as possible. Due to the stiffness of the material, it may seem to be
too tight. By stretching the Net into it’s Box shape will allow easier assembly.
Tip