Everus HGM408 User manual
Welcome
Important Safeguards
How to Use
ŚŽŽƐŝŶŐĂƐƉĞĞĚĨŽƌĂůůĨƵŶĐƟŽŶƐ
Cleaning
Environment
dƌŽƵďůĞƐŚŽŽƟŶŐ
Multifunctional Food Processor
Model: HGM408
Getting Started Guide
110-120V~ 60Hz 500-600W
Welcome to the world of TopChef cooking.
Important Safeguards
Read this user manual carefully before you use the appliance and keep it for future reference.
Danger
- Never immerse the motor unit in water or any other liquid, nor rinse it under the tap.
Warning
- Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
- Never connect this appliance to a timer switch in order to avoid a hazardous situation.
- Do not use the appliance if the mains cord, the plug or other parts are damaged.
- If the mains cord is damaged, it must be replaced by the supplier, a service center authorized by Supplier in order to avoid a
hazard.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance
by a responsible person for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Never let the appliance run unattended.
- Never use your ngers or an object (e.g. a spatula) to push ingredients down the feeding tube while the appliance is running.
Only use the pusher for this purpose.
- Be very careful when you handle the discs, blenderblade unit or food processor blade unit. Be especially careful when you
remove them from the food proces-sor bowl or blender jar, when you empty the bowl or jar and when you clean them. Their
cutting edges are very sharp.
Caution
- Never switch o the appliance by turning the blender jar, the food processor bowl or the juicer bowl. Always switch o the
appliance by turning the speed control knob to OFF.
- Switch o the appliance before you detach any accessories.
- Unplug the appliance immediately after each use.
1
HOW TO USE
1
- Always unplug the appliance before you reach into the blender jar with your ngers or an object (e.g. aspatula).
- Wait until moving parts stop running before you remove the lid of the bowl or jar.
- Never use any accessories or parts from other manufacturers or that Supplier does not specically recommend. If you use
such accessories or parts, your guarantee becomes invalid.
- Do not exceed the maximum content indicated onthe food processor bowl or the blender jar.-Do not use the juicer if the
sieve is damaged.
- Consult the tables in this user manual for the correct quantities and processing times.
- Thoroughly clean the parts that come into contact with food before you use the appliance for the rst time.
- Let hot ingredients cool down before you processthem (max. temperature 80°C/175°F)
- Please wash thoroughly those components which may contact the food before using the product.
- This product has a dual safety system. It will work only after all parts are properly installed.
Place the Bowl on the Main Body, the angle between the handle and the
main body safety switch is about 55 degrees (before placing, make sure
that the Main Body is on a at desktop and it is not shaking)
2
Chopping Meat
3
2
3
4
5
6
7
Hold the handle of the Bowl and turn it clockwise into the Main Body.
When the "▼" on the Bowl is opposite to the Main Body “ ” or a "click" is
heard, it indicates that the Bowl has been rotated in the right position.The
product does not work if the Bowl is not in the right position.
Put the meat into the Bowl. Food that needs to be processed should not
exceed 500g
Insert the power cord into the power supply, and rotate the switch to 1 or 2
shift and start working. Each working time should be less than 30 seconds.
①Cover the Blow with the Bowl Lid.
②Rotate the Bowl Lid clockwise into the Bowl.
When the "click" is heard, it means that the Bowl Lid has been rotated in the right
position, The product does not work if the Bowl Lid is not in the right position.
Put the Drive Shaft into the Bowl.
Put the Chopping Blade on the Drive Shaft.
Kneading Dough
1）Make sure that the Chopping Blade is placed rst when putting the ingredients in the Bowl, so as to avoid the diculty
to assemble Chopping Blade.
2）The Bowl Lid should be in the right postion to avoid not working.
3）Do not process hard food materials, such as coee beans, ice cubes, etc. to avoid cracking Bowl and deformation blunt of
Chopping Blade;
4）Ingredient should not exceed the maximum calibration line of the Bowl, otherwise the crushing eect and life of the
product will be aected.
5）When there is ingredient sticking to the Chopping Blade and Bowl, please be sure to turn o the power, then take out
the food.
1
2
3
Place the Bowl on the Main Body, the angle between the handle and the
main body safety switch is about 55 degrees (before placing, make
sure that the Main Body is on a at desktop and it is not shaking)
Hold the handle of the Bowl and turn it clockwise into the Main Body.
When the "▼" on the Bowl is opposite to the Main Body “ ” or a "click" is
heard, it indicates that the Bowl has been rotated in the right position.The
product does not work if the Bowl is not in the right position
Put the Drive Shaft into the Bowl.
CAUTION
4
4
5
6
7
Put the Drive Shaft into the Bow
Put the our into the Bowl. The our should not exceed 500g
①Insert the power cord into the power supply, and rotate the switch to 1
shift and start working. Each working time should be less than 3 minutes.
②Pour slowly water into the Bowl through chute on the Bowl Lid when
the product start working. Don't pour the water too fast.
①Cover the Blow with the Bowl Lid.
②Rotate the Bowl Lid clockwise into the Bowl.
When the "click" is heard, it means that the Bowl Lid has been rotated in the right
position, The product does not work if the Bowl Lid is not in the right position
1）Make sure that the Dough Hook is placed rst when pouring the our inot the Bowl, so as to avoid the diculty to assemble the Dough
Hook.
2）Do not process hard food materials, such as coee beans, ice cubes, etc. to avoid cracking Bowl and deformation blunt of Dough Hook.
3）Ingredient should not exceed the maximum calibration line of the Bowl, otherwise the crushing eect and life of the product will be
aected.
4）When there is ingredient sticking to the Dough Hook and Bowl, please be sure to turn o the power, then take out the food.
CAUTION
5
Slicing & Shredding
1
2
3
4
Place the Bowl on the Main Body, the angle between the handle and the
main body safety switch is about 55 degrees (before placing, make
sure that the Main Body is on a at desktop and it is not shaking)
Hold the handle of the Bowl and turn it clockwise into the Main Body. When the
"▼" on the Bowl is opposite to the Main Body “ ” or a "click" is heard, it indicates
that the Bowl has been rotated in the
right position.The product does not work if the Bowl is not in the right position
Place the Adjustable Slicing Disc on the Drive Shaft. (Three types of Disc can be
selected according to the processing requirements)
Put the Drive Shaft into the Bowl
5）Please put in the appropriate proportion of our rst, then start the machine to ensure that the Dough Hook works rst, then evenly
and slowly pour into the appropriate proportion of water, do not pour water
too fast, so that water can not form paste with the our
6
1）Before processing, please make sure that the size of food materials can be fully put into the chute.
2）When you put the food into the chute, don't push hard by the Double Pusher to avoid aecting the processing eect and
stuck.
3）Do not put hand or other objects (such as knives, forks, spoons, chopsticks, etc.) into the chute, only use the Double
Pusher.
4）Ingredient should not exceed the maximum calibration line of the Bowl, otherwise the crushing eect and life of the
product will be
aected.When the food stuck on the Disc, please turn o the power rst, and then take out the food.
CAUTION
1
2
3
①Cover the Blow with the Bowl Lid.
②Rotate the Bowl Lid clockwise into the Bowl. When the "click" is heard, it
means that the Bowl Lid has been rotated in the right position, The
product does not work if the Bowl Lid is not in the right position
Insert the power cord into the power supply, and rotate the switch to 1 or 2
shift and start working. Each working time should be less than 30 seconds
①Put slowly food material to the Bowl through the chute on the Bowl Lid.
②Gently use the Double Pusher to push the ingredients through the chute
7
8
Choosing a speed for all functions
Tool/ Attachment Picture Function Speed Maximum
capacities
KB time Rest time Empty working
KB time
Chopping blade Chopping meat
Cutting vegetables Min. – Max. 500g 30sec 1min. 30sec
Dough took
(plastic knife)
Dough making
Dough kneading Min. 500g flour
280ml water 30sec 1min. 30sec
Discs - slicing/
shredding/chipping/
Slicing/ shredding/
chipping food and
vegetables such as
as Carrots, Cheese,
Cucumber, etc
1200ml 1min. 2min. 30sec
Min. – Max.
Cleaning
- Always unplug the appliance before you remove acces sories or clean the motor unit.
-
You can quickly and easily pre-clean the food processor bowl with the pulse button. Simply add some water and
washing-up liquid to the dirty bowl and secure the lid. Then use the pulse button until the bowl is clean. When you
pre-clean the food proces sor bowl in this way, make sure the food processor blade is assembled in the bowl.
9
Environment
Do not throw away the appliance with the normal household waste at the end
of its life, but hand it in at an official collection point for recycling. By doing at
an official collection point for recycling. By doing this, you help to preserve the
environment.
Troubleshooting
Question
The appliance does not go on. Make sure that all assembly indications (on the lid of the bowl, on the bowl, on the motor unit) are aligned.
Answer
The appliance suddenly stops
running.
The lid of the bowl may have become undone during a heavy processing job. Close the lid properly. The
appliance immediately starts working again. The processing job is too heavy. Set the control knob to OFF to
switch off the appliance and remove the mains plug from the wall socket. Then let the appliance cool down
to room temperature. lug in the appliance and switch it on again. Process smaller batches.
Can I clean all removable parts
in the dishwasher? Yes, except the motor unit and the protection cap for the blade unit.
What does ‘pulse’ mean?
When you press the Pulse button, the appliance will run at its highest speed a s long you keep pressing the
button. Using the Pulse button is recommended if you want to have more control over the processing job, for
instance when you are chopping.
Why does the motor produce an
unpleasant smell during
processing?
It is very common for a new appliance to give off an unpleasant smell or emit some smoke the first few times
it is used .This phenomenon will stop after you have used the appliance a number of times. The appliance
may also give off an unpleasant smell or emit some smoke if it has been used too long. In that case you have
to switch the appliance off and let it cool down for 60 minutes.
What should I do when the blade
unit or motor gets blocked during
processing?
Switch the appliance off and use a spatula to dislodge the ingredients that block the blade unit. We also
recommend processing a smaller quantity.
Hong Kong TopChef Appliance Limited
Room P, 4/f, Lladro Centre, 72 Hoi Yuen Road Kwun Tong Kowloon
website: www.topchef.cc/everus
E-mail: everus@topchef.cc
Made In China
CONFROMS TO UL STD.982
CERTIFIED TO CSA STD. C22.2
NO.1335.2.14 & 1335.1
50114642
Table of contents
