Evident OmniScan X3 User manual

DMTA-20102-01EN — Rev. 7
October 2022
OmniScan X3 and OmniScan X3 64
PA/UT Flaw Detector
User’s Manual
This instruction manual contains essential information on how to use this Evident product safely and effectively.
Before using this product, thoroughly review this instruction manual. Use the product as instructed.
Keep this instruction manual in a safe, accessible location.

EVIDENT CANADA, INC.
3415, Rue Pierre-Ardouin Québec (QC) G1P 0B3 Canada
Copyright © 2022 by Evident. All rights reserved. No part of this publication may be
reproduced, translated, or distributed without the express written permission of Evident.
This document was prepared with particular attention to usage to ensure the accuracy of the
information contained therein, and corresponds to the version of the product manufactured
prior to the date appearing on the title page. There could, however, be some differences
between the manual and the product if the product was modified thereafter.
The information contained in this document is subject to change without notice.
Part number: DMTA-20102-01EN
Rev. 7
October 2022
Printed in Canada
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United
States and other countries.
SD Logo is a trademark of SD-3C, LLC.
All brands are trademarks or registered trademarks of their respective owners and third
party entities.

Table of Contents 3
DMTA-20102-01EN, Rev. 7, October 2022
Table of Contents
List of Abbreviations ......................................................................................... 7
Important Information — Please Read Before Use ..................................... 9
Intended Use .......................................................................................................................... 9
Instruction Manual ................................................................................................................ 9
Device Compatibility .......................................................................................................... 10
Repair and Modification ..................................................................................................... 10
Safety Symbols ..................................................................................................................... 10
Safety Signal Words ............................................................................................................ 11
Note Signal Words .............................................................................................................. 12
Safety ..................................................................................................................................... 12
Warnings ............................................................................................................................... 12
Battery Precautions .............................................................................................................. 13
Regulations for Shipping Products with Lithium-Ion Batteries ................................... 15
Equipment Disposal ............................................................................................................ 15
BC (Battery Charger - California, USA Community) ..................................................... 15
CE (European Community) ............................................................................................... 16
UKCA (United Kingdom) .................................................................................................. 16
RCM (Australia) ................................................................................................................... 16
WEEE Directive .................................................................................................................... 16
China RoHS .......................................................................................................................... 17
Korea Communications Commission (KCC) ................................................................... 18
EMC Directive Compliance ................................................................................................ 18
FCC (USA) Compliance ...................................................................................................... 19
ICES-001 (Canada) Compliance ........................................................................................ 20
Warranty Information ......................................................................................................... 20
Technical Support ................................................................................................................ 21
Introduction ...................................................................................................... 23

Table of Contents4
DMTA-20102-01EN, Rev. 7, October 2022
1. Package Content ......................................................................................... 25
2. Overview ...................................................................................................... 27
2.1 Display Touch Screen ............................................................................................... 28
2.2 Main Controls ............................................................................................................ 28
2.3 Power Key .................................................................................................................. 29
2.4 Help Key ..................................................................................................................... 29
2.5 Function Keys ............................................................................................................ 29
2.6 Indicator Lights ......................................................................................................... 29
2.6.1 Power Indicator Light .................................................................................... 29
2.6.2 Acquisition Indicator Light ........................................................................... 30
2.6.3 Alarm Indicator Lights .................................................................................. 30
2.7 Left Side Panel ........................................................................................................... 31
2.8 Right Side Panel ........................................................................................................ 32
2.9 Top Panel .................................................................................................................... 33
2.10 Rear Panel ................................................................................................................... 35
2.11 Harness Anchor Points ............................................................................................. 36
2.12 Special-Purpose Side Door ...................................................................................... 37
3. Basic Operation .......................................................................................... 41
3.1 Turning On and Off the OmniScan X3 ................................................................... 41
3.2 Activating the Automatic Start-Up Mode .............................................................. 42
3.3 Operating on AC Power ........................................................................................... 43
3.4 Lithium-Ion Battery .................................................................................................. 44
3.4.1 Battery Status Indicators ............................................................................... 45
3.4.2 Removing and Installing a Battery .............................................................. 46
3.4.3 Charging a Battery ......................................................................................... 48
3.4.4 Storing Batteries and Extending Life ........................................................... 49
3.4.5 Used Battery Disposal ................................................................................... 51
3.4.6 Warnings on Battery Use ............................................................................... 51
3.5 Software ...................................................................................................................... 52
3.6 Global Positioning System (GPS) ............................................................................ 52
4. Maintenance and Troubleshooting ........................................................ 53
4.1 Preventative Maintenance ....................................................................................... 53
4.2 Instrument Cleaning ................................................................................................. 53
4.2.1 Cleaning the Casing ....................................................................................... 53
4.2.2 Cleaning the Screen and Screen Protector .................................................. 54
4.2.3 Cleaning or Changing the Fan ..................................................................... 54
4.3 Replacing the Touch-Screen Protector ................................................................... 57
4.4 Troubleshooting ........................................................................................................ 57

Table of Contents 5
DMTA-20102-01EN, Rev. 7, October 2022
5. Specifications .............................................................................................. 61
5.1 General Specifications .............................................................................................. 61
5.2 Acquisition Connector Specifications .................................................................... 63
5.2.1 Acoustic Specifications .................................................................................. 64
5.2.2 Acquisition Specifications ............................................................................. 66
5.2.3 Data Specifications ......................................................................................... 67
6. Connector References ................................................................................ 69
6.1 Scanner Encoder Connector .................................................................................... 70
6.2 Alarm and I/O Connector ........................................................................................ 71
7. Connection to a PC with WeldSight Remote Connect ........................ 75
7.1 Launching WeldSight Remote Connect ................................................................. 75
7.2 Connecting the OmniScan X3 to WeldSight ......................................................... 79
Appendix: Accessories and Spare Parts ....................................................... 83
List of Figures ................................................................................................... 87
List of Tables ..................................................................................................... 89

Table of Contents6
DMTA-20102-01EN, Rev. 7, October 2022

DMTA-20102-01EN, Rev. 7, October 2022
List of Abbreviations 7
List of Abbreviations
AC alternating current
AIM Acoustic Influence Map
CLK clock
DC direct current
DIR direction
EFUP environment-friendly use period
FMC Full Matrix Capture
GPS Global Positioning System
I/O input/output
LAN local area network
LCD liquid crystal display
N/A not applicable
P/N part number
PA phased array
RH relative humidity
SDHC Secure Digital High Capacity
TCG time-corrected gain
TFM Total Focusing Method
TFT thin film transistor
TOFD time-of-flight diffraction
TTL transistor-transistor logic
UT ultrasonic testing
WEEE Waste Electrical and Electronic Equipment
WLAN wireless local area network

DMTA-20102-01EN, Rev. 7, October 2022
List of Abbreviations8

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use 9
Important Information — Please Read Before Use
Intended Use
The OmniScan X3 is designed to perform nondestructive inspections on industrial
and commercial materials.
Do not use the OmniScan X3 for any purpose other than its intended use. It must
never be used to inspect or examine human or animal body parts.
Instruction Manual
This instruction manual contains essential information on how to use this product
safely and effectively. Before using this product, thoroughly review this instruction
manual. Use the product as instructed. Keep this instruction manual in a safe,
accessible location.
Some of the details of components illustrated in this manual may differ from the
components installed on your device. However, the operating principles remain the
same.
WARNING
IMPORTANT

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use10
Device Compatibility
Only use this device with the approved ancillary equipment provided by Evident.
Equipment provided by Evident and approved for use with this device is described
later in this manual.
Always use equipment and accessories that meet Evident specifications. Using
incompatible equipment could cause equipment malfunction and/or damage, or
human injury.
Repair and Modification
This device does not contain any user-serviceable parts. Opening the device might
void the warranty.
In order to prevent human injury and/or equipment damage, do not disassemble,
modify, or attempt to repair the device.
Safety Symbols
The following safety symbols might appear on the device and in the instruction
manual:
General warning symbol
This symbol is used to alert the user to potential hazards. All safety messages that
follow this symbol shall be obeyed to avoid possible harm or material damage.
CAUTION
CAUTION

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use 11
High voltage warning symbol
This symbol is used to alert the user to potential electric shock hazards greater
than 1000 volts. All safety messages that follow this symbol shall be obeyed to
avoid possible harm.
Safety Signal Words
The following safety symbols might appear in the documentation of the device:
The DANGER signal word indicates an imminently hazardous situation. It calls
attention to a procedure, practice, or the like, which, if not correctly performed or
adhered to, will result in death or serious personal injury. Do not proceed beyond a
DANGER signal word until the indicated conditions are fully understood and met.
The WARNING signal word indicates a potentially hazardous situation. It calls
attention to a procedure, practice, or the like, which, if not correctly performed or
adhered to, could result in death or serious personal injury. Do not proceed beyond a
WARNING signal word until the indicated conditions are fully understood and met.
The CAUTION signal word indicates a potentially hazardous situation. It calls
attention to an operating procedure, practice, or the like, which, if not correctly
performed or adhered to, may result in minor or moderate personal injury, material
damage, particularly to the product, destruction of part or all of the product, or loss of
data. Do not proceed beyond a CAUTION signal word until the indicated conditions
are fully understood and met.
DANGER
WARNING
CAUTION

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use12
Note Signal Words
The following note signal words could appear in the documentation of the device:
The IMPORTANT signal word calls attention to a note that provides important
information, or information essential to the completion of a task.
The NOTE signal word calls attention to an operating procedure, practice, or the like,
which requires special attention. A note also denotes related parenthetical
information that is useful, but not imperative.
The TIP signal word calls attention to a type of note that helps you apply the
techniques and procedures described in the manual to your specific needs, or
provides hints on how to effectively use the capabilities of the product.
Safety
Before turning on the device, verify that the correct safety precautions have been
taken (see the following warnings). In addition, note the external markings on the
device, which are described under “Safety Symbols.”
Warnings
General Warnings
• Carefully read the instructions contained in this instruction manual prior to
turning on the device.
• Keep this instruction manual in a safe place for further reference.
IMPORTANT
NOTE
TIP
WARNING

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use 13
• Follow the installation and operation procedures.
• It is imperative to respect the safety warnings on the device and in this instruction
manual.
• If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment could be impaired.
• Do not install substitute parts or perform any unauthorized modification to the
device.
• Service instructions, when applicable, are for trained service personnel. To avoid
the risk of electric shock, do not perform any work on the device unless qualified
to do so. For any problem or question regarding this device, contact Evident or an
authorized Evident representative.
• Do not touch the connectors directly by hand. Otherwise, a malfunction or electric
shock may result.
• Do not allow metallic or foreign objects to enter the device through connectors or
any other openings. Otherwise, a malfunction or electric shock may result.
Electrical Warning
The device must only be connected to a power source corresponding to the type
indicated on the rating label.
If a non-approved power supply cord not dedicated to Evident products is used,
Evident will not be able to ensure the electrical safety of the equipment.
Battery Precautions
• Before disposing of a battery, check your local laws, rules, and regulations, and
follow them accordingly.
WARNING
CAUTION
CAUTION

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use14
• Transportation of lithium-ion batteries is regulated by the United Nations under
the United Nations Recommendations on the Transport of Dangerous Goods. It is
expected that governments, intergovernmental organizations, and other
international organizations shall conform to the principles laid down in these
regulations, thus contributing to worldwide harmonization in this field. These
international organizations include the International Civil Aviation organization
(ICAO), the International Air Transport Association (IATA), the International
Maritime Organization (IMO), the US Department of Transportation (USDOT),
Transport Canada (TC), and others. Please contact the transporter and confirm
current regulations before transportation of lithium-ion batteries.
• For California (USA) only:
The device may contain a CR battery. The CR battery contains perchlorate
material, and special handling may be required. Refer to
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
• Do not open, crush, or perforate batteries; doing so could cause injury.
• Do not incinerate batteries. Keep batteries away from fire and other sources of
extreme heat. Exposing batteries to extreme heat (over 80 °C) could result in an
explosion or personal injury.
• Do not drop, hit, or otherwise abuse a battery, as doing so could expose the cell
contents, which are corrosive and explosive.
• Do not short-circuit the battery terminals. A short circuit could cause injury and
severe damage to a battery making it unusable.
• Do not expose a battery to moisture or rain; doing so could cause an electric
shock.
• Only use an external charger approved by Evident to charge the batteries.
• Only use batteries supplied by Evident.
• Do not store batteries that have less than 40 % remaining charge. Recharge
batteries to between 40 % and 80 % capacity before storing them.
• During storage, keep the battery charge between 40 % and 80 %.
• Do not leave batteries in the OmniScan X3 unit during device storage.

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use 15
Regulations for Shipping Products with Lithium-Ion Batteries
When shipping a Li-ion battery or batteries, be sure to follow all local transportation
regulations.
Damaged batteries cannot be shipped through normal routes — DO NOT ship
damaged batteries to Evident. Contact your local Evident representative or material
disposal professionals.
Equipment Disposal
Before disposing of the OmniScan X3, check your local laws, rules, and regulations,
and follow them accordingly.
BC (Battery Charger - California, USA Community)
The BC marking indicates that this product has been tested and
complies with the Appliance Efficiency Regulations as stated in the
California Code of Regulations Title 20, Sections 1601 through 1608 for
Battery Charger Systems. The internal battery charger within this
device has been tested and certified pursuant to the California Energy
Commissionʹs (CEC) requirements; this device is listed on the online
CECʹs (T20) database.
IMPORTANT
WARNING

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use16
CE (European Community)
UKCA (United Kingdom)
RCM (Australia)
WEEE Directive
This device complies with the requirements of directive 2014/30/EU
concerning electromagnetic compatibility, directive 2014/35/EU
concerning low voltage, and directive 2015/863 which amends
2011/65/EU concerning restriction of hazardous substances (RoHS).
The CE marking is a declaration that this product conforms to all the
applicable directives of the European Community.
This device complies with the requirements of the Electromagnetic
Compatibility Regulations 2016, the Electrical Equipment (Safety)
Regulations 2016, and the Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment Regulations 2012.
The UKCA marking indicates compliance with the above regulations.
The regulatory compliance mark (RCM) label indicates that the
product complies with all applicable standards, and has been
registered with the Australian Communications and Media Authority
(ACMA) for placement on the Australian market.
In accordance with European Directive 2012/19/EU on Waste Electrical
and Electronic Equipment (WEEE), this symbol indicates that the
product must not be disposed of as unsorted municipal waste, but
should be collected separately. Refer to your local Evident distributor
for return and/or collection systems available in your country.

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use 17
China RoHS
China RoHS is the term used by industry generally to describe legislation
implemented by the Ministry of Information Industry (MII) in the People’s Republic
of China for the control of pollution by electronic information products (EIP).
The China RoHS mark indicates the product’s Environment-
Friendly Use Period (EFUP). The EFUP is defined as the number of
years for which listed controlled substances will not leak or
chemically deteriorate while in the product. The EFUP for the
OmniScan X3 has been determined to be 15 years.
Note: The Environment-Friendly Use Period (EFUP) is not meant
to be interpreted as the period assuring functionality and product
performance.
电器电子产品有
害物质限制使用
标志
本标志是根据 “电器电子产品有害物质限制使用管理办法 ”
以及 “电子电气产品有害物质限制使用标识要求 ”的规定，
适用于在中国销售的电器电子产品上的电器电子产品有害物
质使用限制标志。
（注意）电器电子产品有害物质限制使用标志内的数字为在
正常的使用条件下有害物质等不泄漏的期限，不是保证产品
功能性能的期间。
产品中有害物质的名称及含量
有害物质
部件名称 铅及其化
合物
汞及其化
合物
镉及其化
合物
六价铬及
其化合物
多溴联苯 多溴二苯
醚
(Pb) (Hg) (Cd) (Cr( Ⅵ)) (PBB) (PBDE)
机构部件 ×○○○○○
主体 光学部件 ×○○○○○
电气部件 ×○○○○○

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use18
Korea Communications Commission (KCC)
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환
경에서 사용하는 경우 전파간섭의 우려가 있습니다 .
EMC Directive Compliance
This equipment generates and uses radio-frequency energy and, if not installed and
used properly (that is, in strict accordance with the manufacturer’s instructions), may
cause interference. The OmniScan X3 has been tested and found to comply with the
limits for an industrial device in accordance with the specifications of the EMC
directive.
附件 ×○○○○○
本表格依据 SJ/T 11364 的规定编制。
○：表示该有害物质在该部件所有均质材料中的含量均在 GB/T26572 规定的限量要求以下。
×：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572 规定的限量要求。
Seller and user shall be noticed that this equipment is suitable for
electromagnetic equipment for office work (class A) and it can be used
outside the home. This device complies with the EMC requirements of
Korea.
The MSIP code for the OmniScan X3 is the following:
MSIP-R-R-OYN-OMNIX3.
The MSIP code for the OmniScan X3 64 is the following: MSIP-R-R-
OYN-OMNISCANX3-64.
产品中有害物质的名称及含量
有害物质
部件名称 铅及其化
合物
汞及其化
合物
镉及其化
合物
六价铬及
其化合物
多溴联苯 多溴二苯
醚
(Pb) (Hg) (Cd) (Cr( Ⅵ)) (PBB) (PBDE)

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use 19
FCC (USA) Compliance
This product has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the product is operated in a
commercial environment. This product generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instruction
manual, might cause harmful interference to radio communications. Operation of this
product in a residential area is likely to cause harmful interference, in which case you
will be required to correct the interference at your own expense.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the product.
FCC Supplier’s Declaration of Conformity
Hereby declares that the product,
Product name: OmniScan X3
Model: OmniScan X3-MR/OmniScan X3-CW
Conforms to the following specifications:
FCC Part 15, Subpart B, Section 15.107 and Section 15.109.
Supplementary information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
NOTE
IMPORTANT

DMTA-20102-01EN, Rev. 7, October 2022
Important Information — Please Read Before Use20
Responsible party name:
EVIDENT SCIENTIFIC, INC.
Address:
48 Woerd Avenue, Waltham, MA 02453, USA
Phone number:
[phone]
ICES-001 (Canada) Compliance
This Class A digital apparatus complies with Canadian ICES-001.
Cet appareil numérique de la classe A est conforme à la norme NMB-001 du Canada.
Warranty Information
Evident guarantees your Evident product to be free from defects in materials and
workmanship for a specific period, and in accordance with conditions specified in the
Terms and Conditions available at https://www.olympus-ims.com/en/terms/.
The Evident warranty only covers equipment that has been used in a proper manner,
as described in this instruction manual, and that has not been subjected to excessive
abuse, attempted unauthorized repair, or modification.
Inspect materials thoroughly on receipt for evidence of external or internal damage
that might have occurred during shipment. Immediately notify the carrier making the
delivery of any damage, because the carrier is normally liable for damage during
shipment. Retain packing materials, waybills, and other shipping documentation
needed in order to file a damage claim. After notifying the carrier, contact Evident for
assistance with the damage claim and equipment replacement, if necessary.
This instruction manual explains the proper operation of your Evident product. The
information contained herein is intended solely as a teaching aid, and shall not be
used in any particular application without independent testing and/or verification by
the operator or the supervisor. Such independent verification of procedures becomes
increasingly important as the criticality of the application increases. For this reason,
Evident makes no warranty, expressed or implied, that the techniques, examples, or
procedures described herein are consistent with industry standards, nor that they
meet the requirements of any particular application.