Excalibur EX-21BS User manual

ITEM
#EX-21BS
A
B C
D
E
FJ
G
H
I
X 24
X 32
X 28
X 4
6
B
D
5
www.general.ca
EX-21BS_V4_R2 - 07-01-2015 © COPYRIGHT GENERAL INTERNATIONAL
4. Attach a long tie bar Dwith it’s edge sitting over
the short tie bar edge as shown in 5, then attach
the second long tie bar.
5. Attach the two top long shelves B, with their
edges sitting over the top short shelf as shown
in 6.
1
C
E
4
2
CLOSE UP VIEW
CLOSE UP VIEW CLOSE UP VIEW
3
1. Attach an adjustable leg extension Fto each leg
Ausing two carriage bolts with washers and nuts
1, as shown.
Note: Select the hole 3 that comes closest to the desired
height for your saw.
2. Attach one top short shelf C and short tie bar E to
one leg as shown, then attach a second leg, 4.
3. Repeat with the second pair of legs.
Note: Position the legs
with the holes for the
lower tie bars closer to
the bottom 2.
FOR EXCALIBUR EX-16 & EX-21 SCROLL SAWS
Adjustable height stand
24 1/2” to 31 1/2”
F
A
UNPACKING
NOTE: Please report any damaged or missing items to your
General International distributor immediately.
LIST OF CONTENTS QTY
A- LEGS................................................................................................. 4
B- LONG TIE BAR.................................................................................. 2
C- SHORT TIE BAR ................................................................................. 2
D- TOP LONG SHELF............................................................................. 2
E- TOP SHORT SHELF ............................................................................ 2
F- ADJUSTABLE LEG EXTENSION ......................................................... 2
G- CARRIAGE BOLT (for stand assembly) ...................................... 24
H- WASHER ......................................................................................... 32
I- HEX NUT ......................................................................................... 28
J- HEX BOLT (to attach scroll saw to stand).................................... 4
ASSEMBLY INSTRUCTIONS
Note: Do not fully tighten the stand bolts until after you have fastened the scroll saw to the stand.

www.general.ca
ITEM
#EX-21BS
5N
1
2
3
4
6
7N
8N
6
2
13
14
9
10
UV
EX-21BS_V4_R2 - 07-01-2015 © COPYRIGHT GENERAL INTERNATIONAL
PART NO. DESCRIPTION SPECIFICATION QTY
EX21-S01 HEX BOLT 5/16” -18UNC X 1” 4
EX21-S02 WASHER 5/16” 32
EX21-S03 TOP SHORT SHELF 2
EX21-S04 TOP LONG SHELF 2
EX21-S05N LEG 4
EX21-S06 HEX NUT 5/16” 28
Adjustable height stand
24 1/2” to 31 1/2”
6. Flip the assembly on one side, then attach the remain-
ing sub-assembly U as shown in V.
7. Attach the leveling feet supplied with your saw to the
bottom of the stand legs (see parts diagram below,
parts # 9,10) and level the stand.
Note: See warning regarding leveling in your scroll saw
manual.
8. Attach your EX-16 or EX-21 scroll saw to the stand using
the 4 supplied hex bolts with 2 washers and a nut as
shown below (#1, 2, 3 and 6), then firmly tighten all
bolts.
ASSEMBLY INSTRUCTIONS (CONTINUED)
PARTS LIST - EX-21BS
PART NO. DESCRIPTION SPECIFICATION QTY
EX21-S07 SHORT TIE BAR 2
EX21-S08 LONG TIE BAR 2
EX21-S09 NUT (INCLUDED WITH MACHINE) 3/8” 8
EX21-S10 LEVELING FOOT (INCLUDED WITH MACHINE) 3/8” 4
EX21-S13 CARRIAGE BOLT 5/16” 24
EX21-S14 ADJUSTABLE LEG EXTENSION 4
CLOSE UP VIEW