Exerpeutic Magnetic Treadmill 4010.6-120116 User manual

Magnetic Treadmill
OWNER’S MANUAL
4010.6-120116

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
If you need help with product information, assembly, or
replacement parts. Please contact customer service.
Email us at:
[e-mail]
Or call us at:
1-844-641-7920
Hours:
8:00 am to 5:00 pm (PST) Daily

SERVICE -------------------------------------------------------------------------2
LABEL PLACEMENT -------------------------------------------------------- 3
PRODUCT SAFETY -----------------------------------------------------------4
OVERVIEW DRAWING ------------------------------------------------------ 5
PARTS LIST --------------------------------------------------------------------- 6
PARTS LIST & TOOL---------------------------------------------------------- 7
ASSEMBLY ----------------------------------------------------------------------8
COMPUTER ---------------------------------------------------------------------11
STORAGE ----------------------------------------------------------------------- 12
ADJUSTMENTS ----------------------------------------------------------------13
LUBRICATION ------------------------------------------------------------------15
TROUBLE SHOOTING & MAINTENANCE ----------------------------- 16
WARRANTY -------------------------------------------------------------------- 17
PARTS REQUEST FORM --------------------------------------------------- 18
TABLE OF CONTENTS
1

IMPORTANT: FOR NORTH AMERICA ONLY
For damage or defective product, questions, replacement parts or any
other service support, please contact our customer service department
(8:00 AM - 5:00 PM Pacific Standard Time, Daily) by below methods:
For Best Service Email:
[e-mail] *
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7921**
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
For damaged or defective product please contact our customer service
before returning to the store.
* Emailing us with the information above will be the best method to
receive a response during peak business hours.
**Response time may vary.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA
SERVICE
2

3
LABEL PLACEMENT

Basic precautions should always be followed, including the following
safety instructions when using this magnetic treadmill: Read all
instructions before using this magnetic treadmill.
1. Check every part of the equipment before exercise. If there is any
defective component, replace it immediately; keep the equipment out of
use until repair.
2. Make sure all parts, bolts and nuts are well assembled and locked before
exercise.
3. Never insert any object into any opening.
4. Never operate this magnetic treadmill if it is not working properly. If it has
been dropped or damaged, or been exposed to water, do not use and
consult an Authorized Service Representative at 1-844-641-7921.
5. Do not attempt any maintenance or adjustments other than those
described in this manual. Should any problems arise, discontinue use
and consult an Authorized Service Representative.
6. Wear comfortable and suitable clothing when using the treadmill. Do not
use the treadmill barefoot, in only socks or in sandals, always wear athletic
shoes. Never wear loose clothing because it could run the risk of getting
caught in the treadmill.
7. Keep children and pets away from the equipment while in use.
8. Do not use the treadmill outdoors. This magnetic treadmill is for
household use only.
9. Only one person should be on the treadmill while in use.
10.Keep the magnetic treadmill on a solid, level surface with the minimum
safety area clearance of 78.7” x 118” of the magnetic treadmill. Be sure
the area around the treadmill remains clear during use and has adequate
clearance.
11.Hold the handlebar with your hands when starting or stopping exercise and
increasing or decreasing the speed.
12.If feeling chest pains, nausea, dizziness, or short of breath, you should
stop exercising immediately and consult your physician before continuing.
13.The maximum weight capacity for this product is 300lbs / 136kgs.
WARNING:Before beginning any exercise program consult your
physician. This is especially important for the persons who are over 35
years old or who have pre-existing health problems. Read all instructions
before using any fitness equipment.
CAUTION:Read all instructions carefully before operating this
product. Retain this Owner’s Manual for future reference.
PRODUCT SAFETY
4

OVERVIEW DRAWING
5

No. Description Qty No. Description Qty
001 Main Frame 1 034 Handlebar End Cap 2
002 Incline Adjuster 1 035 Bolt M8x50 2
003L
Left Stabilizer Tube 1 036 Nylon Washer Ø20xØ9.5x2.5 4
003R
Right Stabilizer Tube 1 037 Washer Ø16xØ8.5x1.5 10
004 Stabilizer 1 038 Washer Ø20xØ10.5x1.5 2
005 Handlebar 1 039 Bolt M10x60 2
006 Computer 1 040 Bolt M8x15 6
007 Computer Support Plate 1 041 Rubber Pad Ø32x8.8 4
008 Hand Pulse Sensor Extension
Wire
1 043 Wire Plug Ø12.5 2
009 Extension Sensor Wire II [Short] 1 044 Bolt M8x40 2
010 Hand Pulse Sensor with Wire 2 045 Incline Adjuster Round Cap Ø25 2
011 Extension Sensor Wire I [Long] 1 046 Bolt M8x45 2
013 Tension Control Knob 1 048 Cap 13# 2
014 Magnet Bracket 1 049 Rear RollerAdjustment Bolt M6x80
2
015 Magnet 5 050 Elliptic End Cap 30x70 2
016 Washer Ø13xØ6.5x1.5 1 052 Rear Roller Ø42x419 1
017 Bolt M8x70 1 053 Bearing Cap Ø42 2
018 Nylon Nut M8 6 054 Bearing 6201 4
019 Nut M6 1 055 Washer Ø16xØ12.3 2
024 Round Knob M10x25 1 056 Big Washer Ø24xØ13.2x2.0 2
025 Ball Knob Ø25xM8 1 057 Rear Roller Axle Ø12x466 1
026 Spring Knob Pin 1 058 Front Roller Axle Ø12x586 1
027 Spring Ø12x1x37 1 059 Clip 2
028 Handlebar Knob Ø48xM10 2 060 Front Roller Ø42x509 1
029 Nut M8 2 061 Anti-slip Pad 2
030 Handlebar Knob Pin Ø12xM8x58
2 062 Running Belt 1
031 Computer Knob M5x15 2 063 Side Rail 2
032 Bolt M5x12 8 064 Running Deck 1
033 Handlebar Foam Grip 2 065 Phillips Self Drilling Screw 6
PARTS LIST
6

No. Description Qty No. Description Qty
066L
Left Protective Cover 1 074 Big Washer Ø20xØ6x1.5 1
066R
Right Protective Cover 1 075 Socket Button Head Cap Screw
M6x55
1
067 Transport Wheel 2 076 Spring Ø8xØ50x1 1
068 Small Magnet 1 077 Sensor with Wire 1
070 Screw ST4.2x20 2 078 Screw ST4.8x10 1
071 Rubber Pad Ø33x18 2 079 Plastic Washer Ø25xØ13x2 2
072 Cable Clip 1 080 Wire Plug 2
073 Bolt M5x10 1 081 Self-Tapping Screw ST 4.2x12 1
PARTS LIST & TOOL
7
5mm Allen Wrench with Phillips
Screwdriver
1 PC

Step 1
Place the magnetic treadmill in the upright position.
Remove six Washers (37) and six Bolts (40) from the Left/Right Stabilizer
Tubes (3L, 3R with the 5mm Allen Wrench with Phillips
Screwdriver provided.
Insert both Left/Right Stabilizer Tubes (3L, 3R) into the Stabilizer (4), and
secure using six Washers (37) and six Bolts (40) that were removed.
Tighten the bolts with the 5mm Allen Wrench with Phillips Screwdriver
provided.
ASSEMBLY
8
Tool:
5mm Allen Wrench with Phillips
Screwdriver

Step 2
Remove the Round Knob (24) from the Stabilizer (4).
Place one hand on the rear end of Main Frame (1) and use the other hand to
pull out the Ball Knob (25). Lower the Main Frame (1) down onto the floor.
TO PREVENT INJURY PLEASE MAKE SURE YOU HAVE A FIRM HOLD
WHEN SETTING DOWN THE DECK.
Remove two Computer Knobs (31) from the Computer Support Plate (7).
Remove two Handlebar Knobs (28) from the Handlebar (5) and then lift the
Handlebar (5) all the way up.
Tighten the Handlebar (5) onto the Stabilizer (4) with two Handlebar Knobs
(28) that were removed.
Turn the Computer (6) upwards and adjust the angle of Computer (6) to the
desired position. Hold the Computer (6) and align computer knob holes.
Tighten the Computer (6) onto the Handlebar (5) with two Computer Knobs
(31) that were removed.
ASSEMBLY
9

Step 3
Install Round Knob (24) to the bigger hole on the Stabilizer (4) and Main
Frame (1) by turning it in a clockwise direction to lock the Main Frame (1) in
place.
Note: Securely tighten Round Knob (24) so that the treadmill is
sturdy.
Plug the Hand Pulse Sensor Extension Wire (8) from the Handlebar (5) into
PULSE receptacle on the back of Computer (6).
Plug the Extension Sensor Wire II (9) from the Handlebar (5) into SENSOR
INPUT receptacle on the back of Computer (6).
ASSEMBLY
10

Specifications:
TIME ----------------00:00-99:59 MIN: SEC
DISTANCE --------0.00-9999 MI
CALORIES --------0.0-9999 CAL
ODOMETER ----- 0-9999 MI
PULSE -------------40-240 BEATS/MIN
Button functions:
MODE: Display function selection.
SET: To set goal values as exercise target.
RESET: To clear goal values.
Display functions:
SCAN Automatically scans through each display mode at 6-second
intervals.
TIME Displays Times.
SPEED Displays the current speed.
DISTANCE Displays distance of exercise sessions.
CALORIES Displays calories burned during exercises.
ODOMETER Displays accumulative distance from combined exercise
sessions.
PULSE Display the BPM (Beats per Minutes).
Set a goal value:
You can set an exercise goal, the value will be counted down for the value you
set.
Press MODE to select a value you’d like to set.
Press SET to set the value, then start your exercise.
How to install the batteries:
1. Remove the battery cover at the rear of computer.
2. Place two "SIZE-AA" batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are in proper
contact with batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial legible, remove batteries and wait 15
seconds before reinstalling.
COMPUTER
11

Remove Round Knob (24) from the Stabilizer (4) and Main Frame (1).
Hold the rear end of the Main Frame (1) by one hand and use the other hand
to pull out the Ball Knob (25). Lift the Main Frame (1) up and align spring
knob pin hole. Release the Ball Knob (25) until the Spring Knob Pin (26)
pop into the hole on the Main Frame (1) to lock the Main Frame (1) in place.
CAUTION: Failure to secure the Main Frame (1) with the Spring
Knob Pin (26) may cause the treadmill accidental fall and cause
bodily injury.
Install the Round Knob (24) onto the Main Frame (1).
Remove two Handlebar Knobs (28) from the Handlebar (5) and then push
the Handlebar (5) all the way down.
Install two Handlebar Knobs (28) back onto the Handlebar (5) to lock the
Handlebar (5) in place.
Remove two Computer Knobs (31) from the Computer Support Plate (7).
Turn the Computer (6) downwards and align computer knob holes.
Tighten the Computer (6) onto the Handlebar (5) with two Computer Knobs
(31) that were removed.
STORAGE
12
Round Knob (24) shall be positioned here
when Main Frame (1) is lifted up in the
upright position.

Adjusting the Tension Control Knob
To increase the load, turn the tension
control knob in a clockwise direction.
To decrease the load, turn the tension
control knob in a counterclockwise
direction.
Adjusting the Incline
There are 3 incline angles (A: 8%,
B: 10%, C: 12%) that the incline adjuster can be
set to.Place one hand on the rear end of the main
frame, then lift the rear end of the main frame up
and use your other hand to adjust the Incline
adjuster to the desired position.
About the Running Belt
Keeping the Belt aligned
This belt is 16 inches wide. It is
recommended that the user’s footsteps
stay on the central 12 inches area. This
will prevent the belt from shifting off the
center. Note: Continuously stepping on
the edge of the Belt will cause the Belt to
shift to either side of the bed.
ADJUSTMENTS
13
Tension Control Knob
12 inches of Suggested
Running Area.
Anti-slip Pad
Anti-slip Pad

Adjusting the Running Belt
1. The running belt is initially set and adjusted at the factory. However it may
come loose during transportation and/or during use. After prolonged use, the
belt will begin to stretch out.
2. If the running belt begins to shift to either left or right side, the user can stand
on the Anti-slip Pads and hold the handlebar with both hands. Then use your
right or left foot to run on the side of the running belt that is opposite to the
direction of the slip.
3. If the belt begins to slip to the left use your right foot on the right side. You
should see the belt start to correct itself by moving back towards the center.
4. However, if the running belt is still shifting away from center, use the 5mm Allen
Wrench provided and turn the left or right Rear Roller Adjustment Bolt 1/2 turn
in a clockwise direction (turn the same side bolt that matches the direction of
the slip).
Then try running on the center of the running belt again. If the running belt is still
shifting away from center, turn the same Rear Adjustment Bolt another 1/4 turn in
the clockwise direction. You should see the belt start to correct itself by moving
back towards the center.
Repeat this procedure until the running belt is centered.
If the running belt is slipping during use, then use the 5mm Allen Wrench provided
and
turn both the left and right rear roller adjustment bolts 1/4 turn in the clockwise
direction. You should now run on the running belt to determine if the running belt
is still slipping. Repeating the above procedure until the running belt is not
slipping.
14
ADJUSTMENTS

The treadmill has already been spread with "Silicone Oil" in advance before
leaving the manufacturing plant. Silicone oil is without volatility and has
gradually permeated through the running belt. There will be no need to
re-spread the oil in normal circumstances. "Silicone Oil" may be re-spread once
the resistance has been increased and the running belt starts rubbing against the
running deck. To hold open the running belt from two sides, apply the silicone oil
with an even motion on the center of the running deck. Allow the silicone oil to
‘set’ for one minute before using the magnetic treadmill.
Attention: Only use "Silicone Oil" lubricants for this equipment. In addition, do
not add any other oil ingredient; otherwise the magnetic treadmill will be
damaged. Do not over-lubricate the running deck. Excess lubricant
should be wiped off with a clean towel.
15

TROUBLE SHOOTING
PROBLEM: Treadmill running belt slips or is not centered on rear roller.
SOLUTION: Refer to the “Adjustments” section on page 15.
PROBLEM: Computer not working correctly
SOLUTION: Check to make sure the computer wires are connected securely.
SOLUTION: Check the batteries are correctly positioned and battery springs are
proper contact with batteries.
SOLUTION: Make sure the batteries are not dead.
PROBLEM: There is no heart rate reading or heart rate reading or is erratic /
inconsistent.
SOLUTION: Make sure that the wire connections for the hand pulse sensors are
secure.
SOLUTION: To ensure the pulse readout is more precise, please always hold on
to the handlebar grip sensors with two hands instead of just with one hand only
when you try to test your heart rate figures.
SOLUTION: Gripping the hand pulse sensors too tight. Try to maintain
moderate pressure while holding onto the hand pulse sensors.
PROBLEM: The magnetic treadmill makes a squeaking noise when in use.
SOLUTION: The bolts may be loose on the magnetic treadmill, please inspect the
bolts and tighten the loose ones.
MAINTENANCE
Cleaning
The magnetic treadmill can be cleaned with a soft cloth and mild detergent. Do
not use abrasives or solvents on plastic parts. Please wipe your perspiration off
the magnetic treadmill after each use. Be careful not get excessive moisture on
the computer display panel as this might cause an electrical hazard or electronics
to fail. Please keep the magnetic treadmill, specially, the computer console, out
of direct sunlight to prevent screen damage. Please inspect all assembly bolts
on the machine for proper tightness every week.
Storage
Store the magnetic treadmill in a clean and dry environment away from children.
TROUBLE SHOOTING & MAINTENANCE
16

MANUFACTURER’S LIMITED WARRANTY
Paradigm Health & Wellness warrants to the original purchaser that this product is free
from defects in material and workmanship when used for the purpose intended, under the
conditions that it has been installed and operated in accordance with Paradigm’s Owner’s
Manual. Paradigm’s obligation under this warranty applies to the following:
COMPONENT LENGTH OF WARRANTY
Structural Frame 3 years
All Other Components 90 days
(computer display, electronics, upholstery, foam, ball bearings, pulleys, belts, cables,
wires, shocks, covers, tension, internal mechanism, wheels, pedals, knobs, accessories
and hardware)
Exclusions from Warranty Coverage:
Paradigm does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any
product failure, product malfunction, or damages attributable to:
1. Improper installation and/or failure to abide by Paradigm’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricane, earthquake, lightning or other natural disaster),
environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt,
grease, oil, etc.);
6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to,
among other things, flake, chalk, or accumulate dirt or stains; or
7. Improper operation, alteration, handling, storage, abuse or neglect of the products.
Paradigm, using its sole discretion, will either repair or replace free of charge any part(s)
proven to be defective under normal home use. Any repair or replacement shall provide
no new warranty coverage, but shall retain only the remaining portion of the original
product’s warranty. This warranty is offered only to the original purchaser and is not
transferable. Proof of original purchase is required.
Ordering Replacement Parts
Replacement parts can be ordered by emailing our customer service department:
[email protected]
Open Daily 8:00 AM - 5:00 PM (PST).
When ordering replacement parts please have the following information ready:
1. Owner’s Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
WARRANTY
17
6

Paradigm Health & Wellness, Inc.
EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO
[e-mail] *
NAME: _______________________________________________________
ADDRESS: ____________________________________________________
CITY ______________ STATE ______________ ZIP ___________________
TELEPHONE: (Day) ____________________________________________
(Night) ____________________________________________
SERIAL#: _____________________________________________________
MODEL#: _____________________________________________________
PURCHASE DATE: _____________________________________________
PLACE OF PURCHASE: _________________________________________
“YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”
* This form can also be faxed in Fax #: [phone]
PART #
DESCRIPTION
QTY
PARTS REQUEST FORM
18