EXP GDC User manual

EXP GDC
Laptop External Graphics Adapter DOCK
Installation Guide (170320)
Professional computer hardware, according to the installation guide to use.
One：Disable DGPU；Two：Install external graphics card；Three：Installation drive；Four：Set control panel。
————————————————————————————————
一、Overview
PCI-E Interface:
Connect PCI-E interface equipment, graphics card, sound card,
array card, video card, acquisition card, etc..
6PIN OUT
Connect video card power supply
8PIN IN
Device power supply interface，（Notebook control power switch）。
DC IN
Support 12 V DC power input, the interface type is outside diameter 5.5MM, diameter 2.1MM, maximum power 150W。
USB：(Note: X4 PCI-E, X4 M.2 version of the interface for the data line interface, the physical interface type HDMI)
This interface only provides 500MA voltage output, does not have any other features。
Date Interface ：
Connect Mini PCI-E、Expresscard、NGFF（M.2）A Key/x1 or M Key/x4、PCI-E x4 Data line。*** Non-standard HDMI interface, the connection of other

equipment caused by the damage to their own.***
ATX PW、PTD、Slim Line Switch:
By default a switch in the OFF state, do not touch。More special features to consult after sales technical support。
二、Disable DGPU
The following operation is performed before the external display card is installed
1、disable the built-in display in the BIOS, off the network to start。Update the BIOS to the latest
Lenovo、Acer：BIOS-Graphic Device-UMA（Graphic Mode-Integrated），PXE Boot to LAN（Network Boot）-Disabled。
THINKPAD：BIOS-Config-Display-Graphics device-Intergrated graphics.OS Detection for NVIDIA Optimus-Disabled
Alienware、Clevo：BIOS-Primary display-IGFX or PCI
HP、DELL：Boot Sequence-Onboard NIC untick，System Configuration-Integrated NIC- Disabled，Power Management-Wake on LAN/WLAN- Disabled
(Without the above options, please follow the following ways to disable)
2、log-in，Device Manager-System devices，One by one, try to disable the "PCI" port, built-in alone disappeared。
（Disable only the "PCI" port that is lost to the built-in single display.）。As shown in Figure：
（System differences, please one by one to disable PCI try）

三、Hardware install
Important note: after all the hardware installed, and then start the notebook
1、ATX POWER
Note: when using the ATX power supply, the graphics card 8PIN 6PIN/ power
supply directly from the power supply connection. Graphics card
The power supply interface must be connected to the. (cable reference right)
四、Graphics driver installation and settings
1、Graphics driver installation
2、Log-in，NVIDIA Control panel-Configure Surround,PhysX-Processor:-GTX***，Check Only use Physx。Manage 3D settings-Global Settings-High
performance mode，Multi-display/mixed-GPU acceleration-Single display performance mode。
Set up, start to enjoy, please install DX11.NET4 DX9 and other necessary patches
（If you can't open the video card control panel, Device manager - the display adapter, right - click to view the external graphics card error code）
Error12 Install DIY EGPU Set hardware conflicts，
Error43 Check the power supply or replace the drive version
NO error Use 2G memory。

Trouble shooting reference
Start troubleshooting
1、Start a black screen, no display card or at the start of LOGO.
1】laptops may not support 4G or more memory, * * * use 2G memory * * * * *.
2】Connected LCD
3】Use sleep to start (do not connect the data line of notebook, start notebook to enter the system after, dot is shut down -- sleep, the computer after
sleeping, connect notebook data line, start notebook.
2、1802 error
1】Brush notebook BIOS white list
3、Blue or in the Windows interface card loading system
1】Reinstall driver
4、Into the system is slow, slow response
1】Replace drive version, install system patch
5、No new hardware
1】Check hardware connection。
2】Not connected to the 3G or SSD property interface
3】BIOS-Expresscard or Mini PCI-E unlock
4】Power supply inspection

Optimization setting
1、Close energy saving options
2、Do not hot plug hardware