EyeRide EYENET 1.4V User manual
INSTALLATION GUIDE
EYENET
EYENET
4.0G
2.4G
A. CONTENT
1 2
4
3
5 6 7 8
x1
x1x1x1x1
x1
x2
x2
EYENET
4.0G 2.4G
Part1: EyeNet Router, Part2: 2.4GHz Female SMA WiFi Antennas x2, Part3: 4.0GHz Male SMA Cellular Antennas x2,
Part4: 4.0GHz Male SMA Cellular Antennas (GPS), Part5: Ethernet Network Cable, Part6: 12 Volt DC Power Adaptert,
Part7: 12 Volt DC Power Pigtail, Part8: 12 Volt Car Plug Power Adaptert (Optional).
EYENET
ON BOARD WIFI
EYERIDE
4G Cellular Female
Antenna SMA Connector
2.4GHz WiFi Male
Antenna SMA Connector
GPS Female
Antenna SMA Connector
Power
Internet
WiFi LAN1 Port LAN3 Port
WAN Port LAN2 Port LAN4 Port
LAN4 Port LAN2 Port WAN Port 12 Volt Power
LAN1 PortLAN3 Port Reset
EYERIDE
MODEL:EYENET 1.4V MODEM:3G/4G/LTE
IP: xx.xx.xxx.xxx
XXXXXXXXXXXX
XXXXXXXXXXXX
POWER: 12VDC---1A
MAC
S/N
IP Address
ModemModel Name
Power Source
MAC
Serial Number
USB Port GPS Female
Antenna SMA Connector
Micro SD
Memory Card Slot
EYENET
4G/LTE
2. The two 2.5GHz WiFi antennas are female and screw onto the pinned male connector.
EYENET
2.4G
2
B. EYENET ROUTER
EYENET
4G/LTE
1. The Antennas are all the same size. However, the two 4G cellular Antennas and one GPS antenna at the front
are male and screw onto the female connector.
4.0G
C. CONNECTING THE SMA ANTENNA CONNECTORS
EYENET
1
TOP VIEW
REAR VIEW
BOTTOM VIEW
FRONT VIEW
EYENET
ON BOARD WIFI
EYERIDE
ON BOARD WIFI
EYERIDE
EYENET
ON BOARD WIFI
EYERIDE
D. POWER ON THE EYENET ROUTER
1. Plugging in the included “power pigtail” connector. The red wire must be connected to 12 Volt DC Power.
Connecting to ignition is recommended. The black wire must be connected to ground.
2. Once you have power on the Eyenet, Power light will turn red and Internet light will started to blink.
3. When the Power light is off and WiFi light is on, your Eyenet is ready to use.
12Volt DC Power
Ground
1 2
3
F. CONNECTING TO INTERNET
Once powered up, connect to the WiFi SSID provided to your by your
EyeRide Technician. There will be no password by default, although you
must click the Accept Terms and Conditions on the splash page which
will come up automatically.
www.EyeRideOnline.com
EYERIDE
E. CONNECTING THE EYENET TO EYERIDE
1. Run 12Volts power to the first slot of Out1.
2. Connect the red wire from the EyeNet’s power pigtail to the second
slot of “Out1.” This will ensure the EyeNet and the Eye Ride are on the
same power schedule.
3. Connect the Ethernet Cable from the one of the internal yellow ports
on the back of the EyeNet to the “Ethernet” port on the top right of the
EyeRide.
EYENET
ON BOARD WIFI
EYERIDE
EyeRide
EyeNet
