Ezviz T55 User manual

Any and all information, including, among others, wordings, pictures, graphs are the properties of

Hangzhou EZVIZ Software Co., Ltd. (hereinafter referred to as “EZVIZ”). This user manual (hereinafter

referred to as “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or

wholly, by any means, without the prior written permission of EZVIZ. Unless otherwise stipulated,

EZVIZ does not make any warranties, guarantees or representations, express or implied, regarding to

the Manual.

About this Manual

The Manual includes instructions for using and managing the product. Pictures, charts, images and

all other information hereinafter are for description and explanation only. The information contained

in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please

find the latest version in the ™ website (http://www.ezviz.com).

Revision Record

New release – January, 2023

Trademarks Acknowledgement

™, ™, and other EZVIZ’s trademarks and logos are the properties of EZVIZ in various

jurisdictions. Other trademarks and logos mentioned below are the properties of their respective

owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH

ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,

AND EZVIZ MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND

NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL EZVIZ, ITS DIRECTORS, OFFICERS,

EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR

INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH

THE USE OF THIS PRODUCT, EVEN IF EZVIZ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL EZVIZ’S TOTAL

LIABILITY FOR ALL DAMAGES EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT.

EZVIZ DOES NOT UNDERTAKE ANY LIABILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE AS

THE RESULT OF PRODUCT INTERRUPTION OR SERVICE TERMINATION CAUSED BY: A) IMPROPER

INSTALLATION OR USAGE OTHER THAN AS REQUESTED; B) THE PROTECTION OF NATIONAL OR

PUBLIC INTERESTS; C) FORCE MAJEURE; D) YOURSELF OR THE THIRD PARTY, INCLUDING WITHOUT

LIMITATION, USING ANY THIRD PARTY’S PRODUCTS, SOFTWARE, APPLICATIONS, AND AMONG

OTHERS.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY

AT YOUR OWN RISKS. EZVIZ SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,

VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, EZVIZ WILL PROVIDE

TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS AND DATA PROTECTION

LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION

BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS TO THE

APPLICABLE LAW. EZVIZ SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH

ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THE ABOVE AND THE APPLICABLE LAW, THE LATTER

PREVAILS.

Table of Contents

Overview ��1

1� Package Contents �� 1

2� Basics �� 2

Get the EZVIZ App ��5

Device Installation��6

1� Install Battaries�� 6

2� Confirm Status of Valve Needle �� 7

3� Assemble the Adapter �� 7

4� Install Device�� 10

5� Calibrate the Travel �� 10

Add Your Device to EZVIZ App��11

Method One: Add by the Gateway(Recommended) �� 11

Method Two: Add by Scanning QR Code�� 12

Operations on the EZVIZ App ��13

1� Manage Your Device�� 13

2� Settings�� 14

SPECIFICATION ��16

EZVIZ Connect��17

1� Use Amazon Alexa�� 17

2� Use Google Assistant �� 18

INFORMATION FOR PRIVATE HOUSEHOLDS ��19

1

Overview

1� Package Contents

Smart Radiator Thermostat (x1)

(hereinafter referred to as "device")

Adapter (x3) AA-sized Battery (x2)

Screw Kit (x1 ) Short Plunger (x1 ) Regulatory

Information (x1) Quick Start Guide (x1)

All device's appearances are subject to the one you have bought.

2

2� Basics

*Wi-Fi

*Programmable

Mode Heat Output*

Copper Ring

Low Battery

Indicator*

Temperature

Button*

Control Knob*

Front View

* Button

Enter network configuration mode (In " " state) Press and hold over 5s until " "

appears

Enable child lock (In " ~ " or " " state) Press and hold for 5s

Off child lock (In " " state) Press and hold for 5s

Flip displayed value (In " " state) Press 5 times continuously

* Control Knob

Adjust temperature Rotate the control knob

3

* Display Icon Description

The preset temperature < 5°C

The preset temperature > 30°C

Enter network configuration mode

Configuring network succeed

Window Opening Detection enabled

Limescale Mitigation enabled

Child Lock enabled

Flashing: calibrating

Permanent on: calibrated successfully

Frost Mitigation enabled

When the temperature rises to 8°C, the device will be closed automatically; when the

temperature is below 5 °C, the device will be opened automatically.

Heat Output

Temperature detection sensor damaged

Device Version

The displayed icon will be changed as your actual device version.

Low Battery Indicator

When the battery power is lower, the device will notice you to replace new batteries through this

icon.

In programmable mode

Permanent on: Network connected

Flashing: Network connection exception

Off: Network not being configured

4

Battery Cover

* Battery Compartment

（Behind the cover）

Back View

* Battery Compartment

Please install 2 AA-sized batteries.

5

Get the EZVIZ App

1. Connect your mobile phone to Wi-Fi (suggested).

2. Download and install the EZVIZ app by searching for “EZVIZ” in the App Store or

Google PlayTM.

3. Launch the app and register an EZVIZ user account.

EZVIZ App

If you have already used the app, please make sure that it is the latest version. To find out if an

update is available, go to the app store and search for "EZVIZ".

6

Device Installation

1� Install Battaries

Press and slide the Battery

Cover down to take off it.

Install 2 AA-sized batteries.

Please check the polarities (+/-) are

correctly alighned.

Close the Battery Cover. “ “ is ashing.

7

2� Conrm Status of Valve Needle

Conrm the status of the valve needle:

- Once the valve needle is ush with the base, please skip this step,

- If not, please repeat step 1, and then check whether the valve needle is ush with the

base.

·When the valve needle is ush with the base, the “ “ will be permanent on.

·The calibration time will take about 6 mins.

3� Assemble the Adapter

The valve gures below are for reference only, please refer to the actual product.

Conrm the valve diameter

Danfoss Caleffi Giacomini

1/2 valve (RA) 1/2 valve 1/2 valve+short plunger

8

Assemble the adapter

Danfoss 1/2 valve (RA)

Please tighten the screws after xing the valve connector.

1

2

3

Calef 1/2 valve

Please put the adapter directly on the valve.

9

Giaocomini 1/2 valve

Install short plunger at the button of the device, and then put the adapter on the

valeve directly.

2

1

10

4� Install Device

Install the device with M30*1.5 screw thread interface of valve, and then tighten the

copper ring.

After installation, please rotate the device and adjust the logo to the front for easy use.

5� Calibrate the Travel

Press Button on the top of the device lightly, it would ash “ “, the device will match

valve stroke, if match succefully, “ “ will turn to “ “ it will active initial setting.

11

Add Your Device to EZVIZ App

The device should be used along with EZVIZ ZigBee Smart Gateway (hereinafter referred to as

"gateway"). Please add gateway to the EZVIZ App by referring to the gateway user manual, and

then add the device to the gateway by following the below steps.

Method One: Add by the Gateway(Recommended)

When adding device by the gateway, place the device as close to the gateway as possible.

1. (In " " state) Press and hold the Button for over 5s until " " appears, the device

enters network configuration mode.

2. Press the Funtion Button of the gateway to make the gateway enter device adding

mode.

3. The device has been added to the gateway successfully and the gateway prompts

adding successfully.

12

If you can not add the device by the method one, please try the following method.

Method Two: Add by Scanning QR Code

1. Log in to your account through EZVIZ App, ensure that gateway has been added in your account,

and then tap the device adding icon and then the QR code scanning interface will be displayed.

2. Please ensure that Press the Battery Cover and slide it downwards to take off it, and then take

the batteries out.

3. Scan the QR code on the Battery Compartment of the device or on the cover of the user manual.

Scan QR Code

4. Please install the batteries back after scanning the QR code.

5. (In " " state) Press and hold the Button for over 5s until " " appears, the device enters

network configuration mode.

6. Add the device by following the wizard on the App.

13

Operations on the EZVIZ App

The App interface may be different due to version update, and the interface of the App you

installed on your phone shall prevail.

1� Manage Your Device

When you launch the EZVIZ app, you can manage your device as needed.

Icon Description

Share. Share your device with anyone you want.

Settings. View or change the device settings.

Low Battery. When the Battery power is lower, the icon will be displayed

to notice user to replace new batteries.

Device Status. The icon will be displayed when the device is heating.

Child Lock. the child lock icon will be displayed when this feature is enabled.

Countdown. Tap to view detailed information of the plan to be executed.

Mode. Tap to select different device mode(Programming, Manual and

Holiday)as you needed.

Power Button. Tap to on/off the device.

14

2� Settings

Programming

Frost Protection

15

Parameter Description

Device Name Customize the name of your device.

Window Opening

Detection

After enabled, the valve switch will be automatically controlled when

the room temperature fluctuates too much.

As soon as the window is closed and the temperature has risen again by

2°C, the device automatically returns to normal operation.

Limescale

Mitigation

After enabled, the device will automatically open the valve and run

for 30s every 2 weeks to mitigate limescale blockage.

Frost Protection After enabled, the device will automatically open when the

temperature drops below 5 °C and rises to 8 °C.

Child Lock Tap to on/off the child lock.

Programming (Under Programming Mode)Tap to add a new plan to automatically

execute it as you set.

Holiday (Under Holiday Mode)Set a desired temperature when you take a

vacation.

Compensation

Temperature

You can set a compensation temperature to correct the actual

temperature

Intelligent Linkage Tap to creat an intelligent scenerio with the device.

Link Device You can see the gateway linked by the device.

Device Information You can see the device information here.

Share Device You can share the device to your family members or guests.

Delete Tap to delete the gateway from EZVIZ App.

16

SPECIFICATION

Parameters Descriptions

Power Source 2AA battery (Do not use the rechargeable battery)

Battery Lifetime 7 months

Communication Mode ZigBee

Temperature Setting Accuracy 0.5°C

Room Temperature Display Range 0 °C ~50°C

Operation Temperature Range 5 °C- 30°C

Shipping & Storage Temperature -10°C- 60°C

Wireless Transmit Range Open distance 100M

Display LED Screen

Connection M30x1.5

17

EZVIZ Connect

1� Use Amazon Alexa

These instructions will enable you to control your EZVIZ devices with Amazon Alexa. If

you run into any difficulties during the process, please refer to Troubleshooting.

Before you start, make sure that:

1.EZVIZ devices are connected to the EZVIZ app.

2.In the EZVIZ app, turn off the "Video Encryption" and turn on the "Audio" in the Device

Settings page.

3.You have an Alexa-enabled device (i.e Echo Spot, Echo-Show, All-new Echo-Show, Fire TV

(all generations), Fire TV stick (second generation only), or Fire TV Edition smart TVs).

4.The Amazon Alexa app is already installed on your smart device, and you have created

an account.

To Control EZVIZ devices with Amazon Alexa:

1.Open the Alexa app and select "Skills and Games" from the menu.

2.On the Skills and Games screen, search for "EZVIZ", and you will nd "EZVIZ" skills.

3.Select your EZVIZ device's skill, then tap ENABLE TO USE.

4.Enter your EZVIZ username and password, and tap Sign in.

5.Tap the Authorize button to authorize Alexa to access your EZVIZ account, so that Alexa

can control your EZVIZ devices.

6.You will see "EZVIZ has been successfully linked", then tap DISCOVER DEVICES to allow

Alexa to discover all your EZVIZ devices.

7.Go back to Alexa app menu and select "Devices", and under devices you will see all your

EZVIZ devices.

Voice Command

Discover a new smart device via the "Smart Home" menu in the Alexa app or the Alexa

Voice Control function.

Once the device is found, you can control it with your voice. Speak simple commands to

Alexa.

Your device's name for example: "show xxxx camera," can be changed in the EZVIZ app. Each time

you change the name of the device, you will need to discover the device again to update the name.

Troubleshooting

What should I do if Alexa fails to discover my device?

Check if there are any Internet connecting problems.

Try to restart the smart device and re-discover the device on Alexa.

Why the device's status is "Ofine" on Alexa?

Your device might have been disconnected from the network. Restart the smart device

and re-discover on Alexa.

Check if your router is connected to the Internet and try again.

For details about countries where Amazon Alexa is available, see Amazon Alexa's official website.

18

2� Use Google Assistant

With the Google Assistant, you can activate your EZVIZ device and watch live by

speaking Google Assistant voice commands.

The following devices and apps are required:

1.A functional EZVIZ app.

2.In the EZVIZ app, turn off the "Video Encryption" and turn on the "Audio" in the Device

Settings page.

3.A TV with functional Chromecast connecting to it.

4.The Google Assistant app on your phone.

To get started, follow the steps below:

1.Set up the EZVIZ device and make sure it works properly on the app.

2.Download the Google Home app from the App Store or Google Play StoreTM and log into

your Google account.

3.On the Myhome screen, tap “+” on the upper-left corner, and select "Set up device" from

the menu list to go to the Set up interface.

4.Tap Works with Google, and search for "EZVIZ", where you will nd "EZVIZ" skills.

5.Enter your EZVIZ username and password, and tap Sign in.

6.Tap the Authorize button to authorize Google to access your EZVIZ account, so that

Google can control your EZVIZ devices.

7.Tap Return to app.

8.Follow the above steps to complete the authorization. When synchronization is

completed, EZVIZ service will be listed under your list of services. To see a list of

compatible devices under your EZVIZ account, tap on the EZVIZ service icon.

9.Now try some commands. Use the name of the camera that you created when you set

up the system.

Users can manage devices as a single entity or in a group. Adding devices to a room

allows users to control a group of devices at the same time using one command.

See the link for more information:

https://support.google.com/googlehome/answer/7029485?co=GENIE.

Platform%3DAndroid&hl=en

Ezviz T55 User manual

Popular Thermostat manuals by other brands