Ezy Spa 104074 User manual

Ezy Spa Hot Tub
Instruction ManualImportant safety guidelines for hot tub usePlease read & understand prior to using your hot tub
ezyspa

23SPECIFICATION--------------------------------------------- 4 INSTALLATION-------------------------------------------- 5 ASSEMBLY--------------------------------------------------- 6 OPERATION OF SPA PUMP---------------------------- 10 SPA MAINTENANCE---------------------------------------- 15 SIMPLE TROUBLE SHOOTING--------------------------- 18CONTENTSSPECIFICATION104074U.S. Regulations MS-18068A4Persons800L(211gal) Φ180*68CM(Φ71”*26.7”) Φ140*68CM(55”*26.7”)68CM(26.7”) 108*3mm110~120V,60Hz,1250W 1200W(15℃water Temperature)650W 5.5mStyleEuropean regulations Product number Capacity Water capacity Outer diameterInner diameter HeightBubble jets RatedpowerHeater power Bubble jetpower Powercord lengthFilter pump specifications4Persons800L(211gal) Φ180*68CM(Φ71”*26.7”) Φ140*68CM(55”*26.7”)650W 5.5mAC12V/35W1880L/420gal/H Pool coverAC12V/50W 2300L/600gal/HΦ142*20cmΦ142*20cm1540W(15℃water temperature)68CM(26.7”) 108*3mm220~240V,50Hz,1545WⅠ.Model and Specification

45SPECIFICATIONINSTALLATION Ⅲ.INSTALLATIONA1：SPApool B1：Pump E1：HoseC1: Pool cover C2：PVCinflatablecover (optional)G1:Valvewrench J1：Backwatercover N1: Repair material ManualD1：Inflation tubeH1: Plug lock H2: KeyK1: Hosel L1: Waterproof repair patchF1：Filter CartridgeI1：Blocker M1：InstructionⅡ.Configuration ListNote: Check all accessories included3.1InstallationSiteRequirements Note:Thegroundshouldbeabletobeartheweightof the pool.Note:Thereshouldbeawaterdrainingsystemaround Note: In order to prevent the danger of electric shock, please do not use the adaptor to connect the pump. ImportantTips：The ground shall be smooth and flat, and there shall be no sharp objects. The user should also consider the totalweightoftheuser,SPAandwater,andensurethat the ground in the use area has Sufficient strength to support it. There is a good drainage system beside the installation area. If the SPA is installed in a place thatdoesnotmeetthesafetyrequirements,anyloss causedisnotcoveredbythewarrantybecauseitis caused by improper use by consumers.1) Indoor installa-tion:Somespecialrequirementsforindoorinstallationthat need to be paid attention to:◎DuringtheinstallationoftheSPA,duringthefilling anddrainingwater,watermayspillontheground.So floor drains and moisture-proof must be installed in this place.◎WhenSPAisused,itwillbringalargeamountof watervapor,andthereshouldbenoarticlesandappli-ancesthatareeasytobeaffectedwithdampintheuse area.Inordertoensureairqualityandusercomfort,it must be installed in a good ventilated environment.Note: Do not install SPA on carpets or other items that areeasydamagedbywater.2) Outdoor installation: ◎Thegroundwherespapoolisonmustbeflatandthere are no sharp objects such as branches and stones nearby.

67b)ConnectthepowerplugoftheSPApumpintotheadapt-edpowersocket,pressthebubblejetbuttontostart inflating the SPA pool (see figure 4 above)PleasefilltheairchamberonthesidewalloftheSPA pool first. If the inflatable top cover is provided, fillthetopcoveraswell. Tips: 1）Howtousethesafetyvalve. ◎ Open the cap of valve;◎ Insert the inflatable hose into the inlet to inflate andinsertthecapofthevalvewhentheinflationis complete;seeFigure5;◎ Deflation: open the cap of valve and let the air out slowlyfromthechamber;2）Howtousearotatedvalve：◎ Open the cap of valve;Press the red point on the up position.◎ Insert the inflatable hose into the air inlet and rotateitinplaceclockwise,andcoverthecapwhenthe inflationiscomplete;seeFigure6；◎ Deflation: open the cap of valve, press the middle redpointonthedownposition,lettheairslowlyout from the chamber.◎Donotuseinanenvironmentwiththetemperature below10degreesCelsius(50degreesFahrenheit).◎ItwillaffecttheheatingeffectofSPA. ◎AlsodonotexposeSPAtothesunforalongtime, whichwillshortentheservicelifeofSPA.◎ThereshouldbeagooddrainagesystemnearSPA pool,as SPA needs to drain.3.2SPApoolassemblyWarning: Please use SPA's matching pump to inflate the pool, and do not over inflate it. Please do not use other high-pressure air pumps for inflation. The normal workingpressureofthepoolis5.0KPa/0.87psi.Exces-sivepressurewillcausetoburstordamagethejoinsof the pool.a) Take the pool on the ground,connect the threaded end oftheinflatabletubetotheinletwithbubblemarkon thepump(seefigure1&2)andinflatetheSPApoolwith anotherendoftheinflatabletube.(seefigure3)1 2 3 4 ASSEMBLYASSEMBLY
ezyspa

3.3Useoflocksockets Insert the key into the hole in the middle of the socket and open or lock it in the direction of the switchshowninfigure8；Fillthewaterwithwaterhoseuntilthewaterreaches theprintedwaterlevellineontheinnerwallofthe pool.Warning:◎ Donotpluginduringfillingthewater.Takecareof thewaterhosetopreventthemfromfallingofftocause thewaterleakage.◎ Pleasecoverthepoolwellwhenyouheatthewater. ◎ Please make sure that the children use the pool under the supervision of adults.◎ When not in use, please cover the pool and lock the buckle to prevent children from entering the pool.3.5ReplacementpumpsBefore replacing the pump, cover the inlet and outlet on theinnerwallofthepoolwithabackwatercoverto preventthewaterfromflowingout,asshowninfigure 113.4Connectingthepumptothepool Note:Thepowerplugmustbepulloutbeforeconnecting the pump to the pool.◎ Assembling the filter cartridge Thefiltercartridgeisscrewedtothewaterinletwall ofthepoolandrotatedclockwise.Seefigure10◎ Fillthepoolwithwater89ASSEMBLYASSEMBLY

Ⅳ. Operation of SPA Pump4.1 Control panel for SPA pumps4.1. 1 " ", "(1)Press the " " or " "key to set the temperature. Each time you press the " " key, (2)Temperature range:" key:1011OPERATING INSTRUCTIONOPERATION OF SPA PUMPOPERATION OF SPA PUMP(1)When the bubble function and other functions are turned off, press this key to turn on the bubble function, .If you need to make bubble again, you just press this key again,the bubble function .(2)When the filtering function is turned on, press the -bubble function key again during the bubble process,the .(3)function are turned on, press the bubble function key to start the bubble function . The heating and filtering function are automatically stoppedfunction key during the bubble process, the bubble func-function and heating function are started .
ezyspa

1213OPERATING INSTRUCTION(4)When the bubble function is turned on, neither the filtering function nor the heating function can be turned on by pressing the filtering key and the heating key.4.1.6Child Lock/Unlock Key Pressthekeyfor5seconds,canachievechildlock function, that is, in any state, all keys are locked, can notbeusedindependently.Ifyouwanttounlockthechild lock,justpressthekeyagainfor5secondsto unlock;4.2Drainage of SPA pool (1) a:Use the plug in the repair bag to block the outlet at the bottom of the pool.see fig A; b:Openthecapoftheoutletpipeundertheouterwallof the pool, see fig B;4.1.4Filter on/off key:(1)When the filtering function is turned off, press the key once to turn on the filtering function. Press the filter function again to turn off.(2)When the filtering and heating functions are turned on at the same time, press the filtering key again, and both heating and filtering functions are turned off at the same time.(3)When the bubble function is turned on, neither the filtering function nor the heating function can be turned on by pressing the filtering key and the heating key. 4.1.5Heating on/off key:(1)When both the heating and filtering functions are turned off, press the heating key.Both filtering and heating function are started immediately(2)When the heating is turned on, press the heating key again, the heating function is turned off and the filtering function canstillcontinuetowork.(3)When heating to the set temperature, it enters the heat preservation state, and whenthepooltemperatureis2 degreeslowerthantheset temperature, the heating function starts automatically. c:Connectawhitedrainpipeinthepoolsetfordrainage, see fig C;(2)PouroutthewaterfromtheSPApumpfirst.seefig 1.Thenconnecttheoutletofbubbleandwateroutlet.see fig2.Pressbubblekeyandmakeitworkfor2-3minutesto blowouttheremainingwaterinsidetheSPApool.OPERATION OF SPA PUMPOPERATION OF SPA PUMP

Ⅴ.SPA MAINTENANCE1415OPERATING INSTRUCTIONSPA MAINTENANCE4.3SPAPoolFilterCartridgeReplacementWarning: The circuit breaker must be cut off before begin-ning spa maintenance to avoid severe risk of injury or death.NOTE: Dirty filter cartridge not only affects the cleaning ofwaterinthepool,butalsoaffectstheheatingeffect of SPA pump. Therefore, it is recommended to clean the filtercartridgeregularlyaccordingtothewatertreat-ment chapter.(1)First pull off the plug (2)Coverthewaterinletandoutletwiththecoverinclud-ed;(3)Rotatecounterclockwisetoremovethefiltercartridge; (Figure 1) (4)Youcanrinsethefiltercartridgedirectlywithwater (Figure 2), but if the filter cartridge is still dirty or has changed color after rinsing, it is recommended that you replace the filter cartridge.(5)InstallthewashedfiltercartridgeintotheSPApool wall.5.1WaterRequirementsforSPA WerequirethePHvalueofthewaterusedinthepoolto bebetween6.5and8.5.IfthePHvalueistoolowortoo high,itwillaffecttheservicelifeofthepoolandpump of SPA and bring harm to human health. The damage of SPA causedbythePHvalueofthewaterqualitywillnotbe coveredbythewarranty.Therefore,wesuggestthatcus-tomerscanusePHtestpapertotestthewaterquality before using it.5.2SPAWaterTreatment Note:Ensurethecleanlinessofthewaterinthepoolis very important for your health. We suggest you do the followingthings:(1)Regularly start the filtration system of SPA pump to cleanthewaterinSPApool;(2)The filter cartridge of SPA pump must be cleaned every 3days,andthefiltercartridgemustbereplacedonaver-ageonceaweekaccordingtothefrequencyofuse. (3)Replacethewaterinthepoolevery3daysandthen cleanthepoolcleanwithacleancloth. (4)SPAcanbetreatedwithsuitablechemicalsforSPA,and thewaterinSPApoolcanbedisinfectedwithappropriate disinfectanteveryday.Thedisinfectantwillkillbacte-riaandvirusesinthewater.PleaseconsultthelocalSPA distributor/seller for details before use.Note:Before using pool chemicals, please consult your local SPA Retailer for more maintenance information. Pay close attention to the chemical manufacturer's instructions. OPERATION OF SPA PUMP

1617OPERATING INSTRUCTION 5.4RepairSPAIf the SPA punctures and leaks air, the repair patch in the attached repair kit can be used for repair. Before repair, the SPA should be drained and deflated, and the damagedpartshouldbewipedclean.Cuttherepairpatch intoashapeofappropriatesize,coatitwithmatching glue, and paste it onto the damaged part. Do not use the newlyrepairedSPAwithin12hours.5.5SPAstorageAccording to the above-mentioned SPA drainage steps, ensurethatthewaterintheSPApoolandthecontrolbox hasbeendrained,takeoutthefiltercartridge,andwipe theSPApoolandSPApumpcleanwithcottoncloth,which can prolong the service life of the SPA. It is recommended that you store the SPA in the original package and put it inawarmanddryplace.Note:It is strictly prohibited to store the SPA pool in an environmentbelowzerodegreesCelsius.Plasticiseasily brittleandshortensitsservicelifewhenexposedtolow temperatureenvironmentorexposedtothesunlightfora longtime.Damagecausedbyimproperstorageinwinter willnotbecoveredbythewarranty.IfSPAisnotusedforalongtime,theresidualwaterin SPApoolandSPApumpmustbedried,otherwisepeculiar smellwillbecausedbydeteriorationofwaterquality.Abuse of SPA or improper use of chemicals, resulting in SPAdamageandlifeinjury,willnotbecoveredbythe warranty.AftereachuseoftheSPApool,werecommendthatyouuse bromine reagents and the chemical floaters to disinfect thewaterinthepool.Firstopenthecapofchemical floaters, then add some bromine reagents, and cover the cap. Put the floaters into the SPA pool. We recommend that youactivatethebubblefunctionwhilethewaterinthe poolisbeingdisinfected,sothatthecirculationofwater and disinfection can be more sufficient. Please look at thefollowingillustration:Warning:SPAcannotbeusedwhileitisbeingsterilized. Themaximumamountofchemicalsshouldnotexceed20tab-lets,otherwisethechemicalswilldestroySPA,andchlo-rine-containing chemicals should not be used.5.3CleanSPA Dirtonthebody,swimsuitandscaleinwaterareeasyto adhere to SPA pool and pump body after heating, so it is necessarytowipethesurfaceofSPApoolwithsoftcloth andneutraldetergentfrequently,andafinebrushisused towipethescaleattachedtothewaterinletandoutlet topreventscalefromblockingthewaterinletandoutlet, thus affecting the normal use of SPA pump.Note: Do not use hard brushes to clean the surface of the pool. SPA MAINTENANCESPA MAINTENANCE

Failure SPA Cannot runSPA No heatingThewave-makingsystem doesnotworkWater filtration does notworkWhen the pump temperature is too highSolutionPossible phenomena Notpoweredon RCD TripResidual current device damageFilter cartridge dirty The inlet and outlet pipes are blockedControlboxerrorBuzzer does not stopInsufficient filtering timeFilter cartridge clead. Thewaterisnotclean. Improper handling of water.Increase filtration timeCleaning/Replacing of filter cartridgeReplacethewater Refer to the chemical instruction operationSPA The buzzer of the pump sounded continu-ouslySPA Water tank leaks Water is not cleanSPA Pool damageUse the provided repair patchTemperaturesettoolow Filter cartridge too dirty Thewaterlevelistoo lowElectric heating does notworkDisconnect the plug and waitforthepumpto cool before startingThe temperature Protec-tion 30Minutesareautomat-ically turned offSPA automatic pump protectionRestart Bubble button. If it cannot be start-ed,please contact after-sales serviceCheckpowersupply ResetRCDOrthepower cord load is not up to 2000W Or 10AIfyoucanstillwork normally, please contact the after-sales serviceSet a higher tempera-tureCleaning/replacing filter cartridgeContinue to fill the waterandraisethe waterlevelCall for helpCleaning/Replacing filter cartridgeCheckifthewater inlet and outlet are blocked by foreign bodies such as scaleIf you still can not worknormally,please contact the after-sales serviceCleaning/Replacing filter cartridgeCheckifthewater inlet and outlet are block by foreign bodies such as scalePress and hold the filterkey3secondsto eliminate sound1819SIMPLE TROUBLESHOOTING Ⅵ.Simple troubleshootingOPERATING INSTRUCTIONSIMPLE TROUBLESHOOTING