Faber Relaxed L User manual

Relaxed L
Installation
guide
IRLU
K
40010636 - 0736

1 < <<<
UK IRL
General
1-1 (Wood set)
1-2 (Twigset)
1-3 (Pebbles)
1-4 1-5

>>>> 2
UK IRL
Relaxed L Frameless
2-1 2-2
2-3 2-4

3 < <<<
UK IRL
Relaxed L Framed
3-1 3-2
3-3 3-4
B
A

>>>> 4
UK IRL
4-1
4-2 4-3
4-4 4-5
4-6 4-7
3
1
2

5 < <<<
UK IRL
Inleiding
1Content............................................................................................... 6
2Safety and general information .................................................................. 7
3Installation requirements ......................................................................... 8
3.1 Builders opening.............................................................................. 8
3.2 Flue requirements............................................................................ 9
4Instruction for Installation .......................................................................11
4.1 Gas connection ..............................................................................11
4.2 Preparing the appliance....................................................................11
4.3 Place the appliance.........................................................................11
4.4 False chimney Brest ........................................................................11
4.5 Building the False Chimney Brest with a Frameless situation........................11
4.6 Building the False Chimney Brest with a Frame........................................12
4.7 Placing the Pebbles or placing the Log/Twig set ......................................12
4.8 Placing the glass.............................................................................12
4.9 Flue requirements...........................................................................13
5Commissioning (functional checks) .............................................................14
5.1 Pilot ignition check .........................................................................14
5.2 Check functional burner and pilot burner...............................................14
6Handing over (final check and customer briefing) ...........................................15
7Servicing ............................................................................................15
7.1 Routine anual servicing ....................................................................15
7.2 Cleaning the glass...........................................................................15
7.3 Cleaning the combustion chamber and burner.........................................16
7.4 Rebuild to other gas category (e.g. Propane/butane) ...............................16
Appendix A: Example calculation.....................................................................17
Appendix B: Flue restrictor............................................................................18
Appendix C: Installation of the flue..................................................................19
Appendix D: Technical specifications................................................................20
Appendix E: Dimensions Relaxed L with Frame ....................................................21
Appendix F: Dimensions Relaxed L Frameless......................................................22
Appendix G : Dimensions Ventilation grid...........................................................23
Appendix H : Dimensions Service Hatch.............................................................24

>>>> 6
UK IRL
1Content
Note: these instructions should be read carefully and retained for future reference. Please
leave these instructions with the user.
This guide is concerning the following types of appliances:
•RELAXED L with frame
•RELAXED L frameless
Special features:
•Room sealed appliance, inlet and outlet are led to the outside using a natural
draught concentric pipe system (100 mm/150 mm) (no power fan required)
•Air supply and flue-gases go to outside atmosphere through wall or roof
•Remote Control standard
•Faber false chimney breast optional
•Meets the requirements of the European Gas Appliance Directive (GAD) and carries
the CE mark

7 < <<<
UK IRL
2Safety and general information
Before installation, ensure that the local distribution conditions (identification of the type
of gas and pressure) and the adjustment of the appliance are compatible.
This gas appliance is factory set and can not be adjusted.
This appliance does not contain any component manufactured from asbestos or any
asbestos related products.
Ventilation
This appliance is room-sealed and doesn't require purpose provided ventilation.
Never use the appliance if it has a broken glass.
General safety
It is the law in the UK that all gas appliances, are installed by a competent person in
accordance with the Gas Safety (Installation and Use) Regulations (as amended), the
relevant British Standards for Installation work, Building Regulations, Codes of Practice and
the manufacturers instructions.
Always use an additional guard if there are elderly, infirm or children in the same room of
the appliance.
The installation should also be carried out in accordance with the following where
relevant:
•BS5871 Part1
•BS5440 Parts 1 & 2
•BS1251
•Building Regulations Document J (as applicable)
•Building Regulations and Standards issued as relevant by the Department of the
Environment or the Scottish Development Department
•In the Republic of Ireland installation should be carried out in accordance with
IS813, ICP3, IS327, Building Regulations, Codes of Practice, the manufacturers
instructions and all other regulations in force
Failure to comply with the above could leave the installer liable to prosecution and
invalidate the appliance warranty.

>>>> 8
UK IRL
3Installation requirements
Note: Since the appliance is a source of heat, circulation of air occurs. Therefore it is of
importance that you do not use the appliance shortly after a renovation of the home.
Because of the natural circulation of air, moist and volatile components from paint,
building materials, carpet etc. will be attracted. These components can settle onto cold
surfaces in the form of soot.
As on all heat producing appliances, soft furnishings such as blown vinyl wallpaper placed
too near to the appliance may become scorched or discoloured. This should be born in
mind when installing the appliance.
3.1 Builders opening
The Relaxed L can be build in a non-combustible fire place or builders opening. This could
be either an existing builders opening or a new made prefab builders opening.
When you apply your own false chimney breast design to the Relaxed L you have to meet
these general requirements:
•The false chimney breast has to be made of inflammable material
•Always install the appliance before building up the false chimney breast
•Check figure 2-3 for the dimensions
•Always ventilate the space above the appliance using vents to assure a good air-
circulation
•The plaster of the outside has to be resistant to a high temperature. Therefore use the
plaster materials especially made for this, to prevent discolouring (min. 100 °C
temperature resistant)
•Make sure the plaster dries well before using the appliance. Let the thickness in mm be
the number of days the plaster has to dry
3.1.1 False chimney breast Relaxed L frameless
•Use the steel building guide (fig. 2-1) mounted on the front of the appliance
•Make a framework of metal studs around the steel building guide; keep in mind the
thickness of the Promatec you use!
•Place metal studs at every corner of the false chimney brest; keep in mind the
thickness of the Promatec you use!
•Build with Promatec around the steel building guide (fig.2-2)
•Build the rest of the false chimney brest
•Use 12 mm Promatec for the front of the false chimney breast.

9 < <<<
UK IRL
3.1.2 False chimney brest RELAXED L with frame
•Make a framework of metal studs around building guides A and B (fig. 3-1); keep in
mind the thickness of the Promatec you use!
•Place metal studs at every corner of the false chimney brest; keep in mind the
thickness of the Promatec you use!
•Build with Promatec around the appliance against the building guides A and B (fig.3-1);
keep in mind that the appliance has to stick out of the walll and therefore nothing
must be build before the building guides!
•Build the rest of the false chimney brest
3.2 Flue requirements
•The appliance is of the type C11/C31. The appliance will need to be supplied with
the approved flue pipes and terminal, it is not possible to supply your own
•a horizontal extension with elbows is allowed for a maximum of 5 meters
(depending on the situation)
•Minimal 1 meter vertical and maximal 12 meters vertical (depending on situation)
Determine on the base of the example calculations in Appendix A and on the base of the
table in Appendix B if the desired situation is possible. To establish this you will need to
calculate:
•The effective height (this is the real difference in height between the upper side of
the appliance and the terminal)
•The total horizontal extension. This is the total horizontal flue length where:
1. each 90-degree bend, which is in the horizontal area, counts for 2 meter
2. each 45-degree bend, which is in the horizontal area, counts for 1 meter
3. elbows and bends at the transition of horizontal to vertically are not to be
counted
4. the wall mounted terminal or roof terminal counts for 1 meter
3.2.1 Terminal position
Verify if the required terminal position meets the local installation regulations regarding
disturbance, good functioning and ventilation (see also appendix G).
Note:
•The terminal must be located so that the outlet is not obstructed. If the flue
terminal is located within 2 meters of a footway path or where people could come
into contact with it, then a suitable terminal guard must be fitted

>>>> 10
UK IRL
•Terminals located close to shared walkways, footpaths etc. could be subject to
legal constraints and this should be pointed out to the customer before installation.
If in any doubt about flue location advice should be sought from local building
control, or if appliance-related, from the manufacturer including wherever possible
a dimensioned sketch
•Avoid locating the terminal in close proximity to plastic materials such as gutters or
other combustibles. If this is unavoidable then a suitable deflector should be made.
•Some important requirements for a good functioning are
•The wall-mounted terminal has to be at least 0,5 m off
oCorners of the building
oBelow eaves
oBalcony's etc. unless the duct is dragged to the front side of the overhanging part
oThe roof mounted terminal has to be at a distance of at least 0.5 meters of the
sides of the roof, excluded the ridge
3.2.2 Using an existing chimney as air inlet
You can connect the appliance onto an existing chimney. The existing chimney then
functions as air supply, where a flexible stainless steel liner (to BS715) of 100 mm performs
the flue function.
Requirements:
•Any existing chimney used as an air supply must only service this a0ppliance.
•A chimney that has previously been used for solid fuel must be swept before use.
•The existing chimney needs to be airtight.
•The existing chimney needs to have an opening of min. 150 x 150 mm.
•The chimney needs to be intact and well looked after.
•Use the adjustable roof-mounted-terminal especially made for this, and the
chimney connection set.

11 < <<<
UK IRL
4Instruction for Installation
4.1 Gas connection
Installation pipes should be in accordance with BS 6891. Pipe work from the meter to the
appliance must be of adequate size.
The complete installation including the meter must be tested for soundness and purged as
described in the above code.
A means of isolation must be provide in the supply to facilitate servicing.
The connection should be made in 8 mm copper or similar semi flexible tube. (max 1
meter). Ensure that the gas pipe does not interfere with the removal or replacement of
the burner tray or of the controls.
The gas connection is nut and olive suitable for 8 mm pipe.
4.2 Preparing the appliance
•Remove the packaging and pallet under the appliance
•Don’t forget to remove the separate packed parts out of the top of the appliance
•Pre-adjust the appliances’ height by adjusting the couple legs
4.3 Place the appliance
•Check paragraph 3.1 before commencing installation
•If possible, first place the appliance before assembling the flue
•Check if the floor and wall are sufficiently level and perpendicular. Fix if not
•Prepare the gas-connection; normally the gas control block is positioned at the
right side but these can be positioned anywhere within 1,2 m of the centre of the
appliance
•adjust the appliances’ height
•Make sure the appliance is level
4.4 False chimney Brest
Note: Always place ventilation grids in the False chimney Brest
4.5 Building the False Chimney Brest with a Frameless situation
•Use the steel building guide (fig. 2-1) mounted on the front of the appliance
•Make a framework of metal studs around the steel building guide; keep in mind the
thickness of the Promatec you use!

>>>> 12
UK IRL
•Place metal studs at every corner of the false chimney brest; keep in mind the
thickness of the Promatec you use!
•Build with Promatec around the steel building guide (fig.2-2)
•Build the rest of the false chimney brest
4.6 Building the False Chimney Brest with a Frame
•Make a framework of metal studs around building guides A and B (fig. 3-1); keep in
mind the thickness of the Promatec you use!
•Place metal studs at every corner of the false chimney brest; keep in mind the
thickness of the Promatec you use!
•Build with Promatec around the appliance against the building guides A and B (fig.3-1);
keep in mind that the appliance has to stick out of the walll and therefore nothing
must be build before the building guides!
•Build the rest of the false chimney brest
4.7 Placing the Pebbles or placing the Log/Twig set
•Place the pebbles (fig 1-3) or in case of a Log/Twig set spread the bottom of the
appliance over with the decorative black/yellow materials
•Place the Twig set according to figure 1-1 or place the Log set according to fig.1-2
Never spread over more than one layer pebbles or embers!
Always check if the pilot light can be seen!
4.8 Placing the glass
Two suction pads are delivered with the appliance to make placing/removal easier.
Always clean the suction lifters before use
Place the suction lifters on the glass and bring the handles towards each other (see
figure 4-1)
Slide the top of the glass carefully in the glass opening and simultaneously slide the
glass upwards
Turn the bottom of the glass backwards
Slide the glass downwards till it stops
Place the strips at each side (see figures 4-3 and 4-4)
Place the seal cord around the glass opening and check for soundness
Place the decorative bottom strip
Place the decorative side strips over de magnets
(if applicable) Place the Frame
Remove stains from the glass (they can’t be removed after the fire has been lit)

13 < <<<
UK IRL
4.9 Flue requirements
The appliance is of the type C11/C31. The appliance will need to be supplied with the
approved flue pipes and terminal, it is not possible to supply your own.
The minimum effective height of the flue system must be 1 meter!
4.9.1 Flue routing
- The terminal locations, through the wall as well as through the roof
- A horizontal extension with elbows is allowed for a maximum of 5 meters (depending
on the type and situation)
- Vertical max. 12 meters. (depending on the type and situation)
Determine on the base of Appendix A and B depending on the type and terminal position, if
the desired situation is possible. To establish this you will need to calculate:
- The effective height (this is the real difference in height between the upper side of the
appliance and the terminal);
- The total horizontal extension. This is the total horizontal flue length where:
oEach elbow, which is in the horizontal area, counts for 2 meters;
oEach 45-degree bend, which is in the horizontal area, counts for 1 meter;
oElbows and bends at the transition of horizontal to vertically are not to be
counted;
oThe wall mounted terminal counts for 1 meter.
4.9.2 Flue restrictor
If applicable, in the table is also stated the size of a flue restrictor. This restrictor needs
to be fitted in the combustion chamber when placing the appliance (see chapter 4.2).
Normally the smallest flue restrictor is fitted.

>>>> 14
UK IRL
5Commissioning (functional checks)
5.1 Pilot ignition check
•Ignite the pilot light as described in the user manual
•Check if the pilot burner stays alight
•Extinguish the pilot burner
5.2 Check functional burner and pilot burner
The appliance is preset to give the correct heat input. No further adjustment is necessary.
Always check the inlet pressure and burner pressure:
•Turn off the gas valve on the appliance
•Turn the inlet pressure test point C and apply the manometer
•Check if the measured pressure is the same as the prescribed pressure
•Perform this measuring when the appliance burns on full capacity and when only the pilot
ignition burns
•When the pressure is too low, check if the gas pipes are made of material with the right
diameter
•When the pressure is too high (more than 5 mBar overpressure) you may not install the
appliance and you should contact your gas company
•Always check the burner pressure when the functional pressure is right
•Open the burner pressure test point D
•The pressure should match the described pressure. If this is not the case, then contact the
supplier
Note: After checking the burner pressure, the inlet pressure test point has to be shut and
checked for gas-tightness.
A. Governor
B. Inlet pressure testpoint
C. Burner
p
ressure test
p
oint
A
B C

15 < <<<
UK IRL
6Handing over (final check and customer briefing)
•Instruct the customer on the full operation of the appliance and the remote
control, including replacement of batteries
•Advise the customer how to clean the appliance including the glass
•Hand over these instructions including the user guide to the consumer
•Recommend that the appliance should be serviced by a competent person at least
once a year
7Servicing
To ensure safe, efficient operation of the appliance, it is necessary to carry out routine
servicing at regular intervals.
It is recommended, that the fire is inspected/serviced by a competent person at least once
a year.
Important: Turn off the gas supply before commencing any servicing. Always test for gas
soundness after refitting the appliance!
7.1 Routine anual servicing
•Clean (if necessary):
a. the pilot system
b. the burner
c. the combustion chamber
d. the glass
•Check the log lay and replace the embers (if applicable)
•Do the functional test as described in chapter 6
•Check the flue system and terminal on damage and soundness (visual inspection)
7.2 Cleaning the glass
Depending on the intensity of use, you can get a deposit on the glass. Remove the glass
(see chapter 4.6).
Remove the deposit with a special ceramic glass cleaner (ceramic cook-top cleaner) as
follows:
•Remove the front and the back.
•Clean the glass. Handle the glass with clean hands, wear gloves if possible.
•To fit the glass, proceed in reverse order. Make sure that the log set has been
installed correctly before fixing the glass.

>>>> 16
UK IRL
Attention:
Before placing the glass: check the glass sealing rope is in good condition and makes an
effective seal. Be sure that there are no fingerprints on the glass. It is not possible to
remove those prints after you burn the appliance for a while (they are burnt in). Place the
glass in front of the appliance and fix the glass frame or use the glass clamps.
7.3 Cleaning the combustion chamber and burner
If the burner is visibly damaged, this can affect the distribution of the flame, if so then
replace the burner.
Burner tray assembly
Remove the front, glass, and log holder (if applicable)
Break the gas supply at the control valve.
Unscrew the burner assembly and take them out of the combustion chamber.
7.4 Rebuild to other gas category (e.g. Propane/butane)
Rebuilding to another gas category is only possible by exchanging the complete burner
plate. Ask your local dealer and bring the PIN (Product Identification Number) of the
appliance.

17 < <<<
UK IRL
Appendix A: Example calculation
Example calculation 1:
Calculating horizontal extension fig. 2a:
Flue length C + E = 1m + 1m
2 m
ElbowsD=2m 2m
Total horizontal extension
4 m
Measure or calculate effective height (Hvert)
Flue length A
1 m
Roof mounted terminal 1 m
Total effective height 2 m
Example calculation 2:
Calculation horizontal extension fig. 2b:
Flue length J + L = 0,5 + 0,5 1 m
Elbows K + M = 2m + 2m 4 m
Terminal 1m
Total horizontal extension 6 m
Calculation effective height (Hvert)
Flue length H 1 m
Looking up in the table in Appendix B shows that this
situation is not allowed
Always check if the calculated situation is allowed (see Apppendix B: Flue restrictor)
Ex.1
Ex .2

>>>> 18
UK IRL
Appendix B: Flue restrictor
Determining of the right flue restrictor:
•Calculate the total horizontal- and vertical length of the flue, according to the
calculations displayed above
•Determine according to the table the right flue restrictor size
•When meeting an X, and when the values are outside the table, the combination is
not allowed
•Normally the 30 mm flue restrictor is preinstalled
Horizontal length (m)Relaxed
L 0 1 2 3 4 5 6
0 x x x x x x x
0.5 x x x x x x x
1 0 0 0 x x x X
1.5 30 30 0 0 x x X
2 30 30 30 0 0 0 0
3 40 30 30 30 0 0 0
4 40 40 30 30 30 0 0
5 50 40 40 30 30 30 0
6 50 50 40 40 30 30 0
7 50 50 50 40 40 40 x
8 60 50 50 40 40 x x
9 60 60 50 50 x x x
10 65 60 60 x x x x
11 65 65 x x x x x
Total effective height (m)
12 65 x x x x x x

19 < <<<
UK IRL
Appendix C: Installation of the flue
Connection with use of concentric duct material
Make a hole of ø 153 mm for the wall or roof mounted terminal.
The horizontal pipes need to rise away from the appliance at a rate of 3 degrees
per metre
Build the system starting from the appliance on.
Make sure you place the pipes in the right direction, the narrow end towards the
appliance.
Make sure the pipes are fixed sufficiently, a wall clamp every 2m, so the weight of
the pipes is not resting onto the appliance.
The outside of the pipe can become hot (140 degrees). Stay 50 mm away from wall
surface or sealing. Make sure to provide sufficiently heat resistant isolation when
going through the wall or roof.
Because of expansion or cooling down the concentric pipes can turn loose. It is
recommended to fix the spring clip with a self tapping screw at inaccessible places.
To get the exact measure flue length you can use cut down concentric pipe, wall
mounted terminal or roof mounted terminal. To obtain a smoke sealed connection,
the inner pipe must be 20 mm longer then the outside pipe.
Connection onto an existing chimney
For connection onto an existing chimney see the installation guide delivered with the
chimney connection set