Fanimation Brewmaster FP10 Series User manual

OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Model No. FP10 / 20 Fan Series
Model No. FP1280 Motor Series
The Brewmaster®
Belt-Driven Ceiling Fans
Suitable for use with Solid State Speed Controls
WARNING: Support Directly From Building Structure
Long Neck FP20
Net Weight 15 lbs
(6.8 kg)
Short Neck FP10
Net Weight 11 lbs
(5.0 kg)
Motor Assembly
Net Weight 15 lbs
(6.8 kg)

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during
the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned
to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to
defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser
will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we
will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,
tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of
heat or humidity, or as a result of any modification to the original product.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such
as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before
servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to
ensure that they do not play with the appliance.
Additional Safety Instructions
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999). Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation
should be made or approved by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 100 lbs. (fan and accessories not to exceed 35
lbs. or 16 kgs.). Outlet boxes are not acceptable for fan support. See page 6 of owner’s manual for support requirements. Consult a
qualified electrician if in doubt.
4. CAUTION: To reduce the risk of personal injury, mount the fan base to a ceiling joist or structural member using the hardware
provided with your fan.
WARNING: Support Directly from Building Structure.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical
knowledge or experience, have your fan installed by licensed electrician.
7. Suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with Fan Speed Control Part No. UC7051FMR,
manufactured by Rhine Electronic Co., Ltd.
WARNING: TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH AN ISOLATING WALL CONTROL/SWITCH.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE ISOLATING WALL
CONTROL/SWITCH.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PC
peripheral, then shall include the following or equivalent:
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.
8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a grounded
conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be connected to an ungrounded
conductor power supply. If the conductor of a fan is identified for equipment grounding, then it should be connected to an
equipment grounding conductor.
WARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage to the
ceiling fan's remote control unit.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac-
company authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid
damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or
implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and
fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation
will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,
except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary
10. A certain amount of wobble is normal and should not be considered a problem or a defect.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
Table of Contents
Motor Assembly- Unpacking Instructions and Parts Identification . . . . . . . . . . . . . . . . . . . . . .
Pulley Assembly-Unpacking Instructions and Parts Identification . . . . . . . . . . . . . . . . . . . . . .
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Set Your Switch Cap Remote Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Set Up Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Hang and Wire Your Ceiling Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Belt Splicing Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting the Fan Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions-Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Install Your Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exploded-View Drawing & Parts List, Motor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List, Pulley Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exploded-View Drawing, Pulley Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5
6
6
7
7
8
10
11
12
13
14
14
14
15
16
17

This manual is designed to make it as easy as possible for you
to assemble, install, operate, and maintain your ceiling fan
4
Motor Assembly- Unpacking Instructions and Parts Identification
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
.detpurretniebuoydluohsecalpruoygnidnifnilufpleheblliwdnadetelpmocneebevahspets
Wiring outlet box and box connectors must be of type re-
quired by local code. The minimum wire would be a 3-con-
ductor (2-wire with ground) of the following size:
NOTE: Place the parts from the loose parts bags in a
small container to keep them from being lost. If any parts
are missing, contact your local retailer.
Tools Needed for Assembly Materials
•One Phillips head screwdriver
•One stepladder
•One ¼ ”blade screwdriver
•916 ”Socket head wrench
•One wire stripper
Wire Size A.W.G.Installed Wire Length
14
12
Up to 50 ft.
50 - 100 ft.
NOTE: If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 15)
Check to see that you have received the following parts:
• Fan Motor Assembly with built-in control receiver
and hardware parts (Figure 1)
• Pulley Head Assembly and hardware parts (Figure 2)
FP1280
Motor Assembly
with
Switch Cap
Receiver
Belt Clamps (2)
“J” Lag Bolt,
1/4˝ x 2˝ (1)
Rivet Tool
Punch Tool
FP1280 Motor Assembly and Hardware Parts Identification
NOTE: The illustration shown is not to scale or its actual configuration may vary.
Parts and packings subject to change without notice.
Motor Assembly
Lag Bolts, 1/4˝ x 2˝ (4)
& Flat Washers,
Ø5xØ14x1 mm(4)
Wire Nuts (3)
Figure 1
▲ WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 9). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
▲ WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
/
Rivets, 3/32˝ x 7/32˝ (8)
& Rivet Washers,
0.1x0.23x0.35 mm (8)
Hand-held Remote

5
Pulley Assembly-Unpacking Instructions and Parts Identification
¼˝ x 2˝ Lag Bolts (4) &
Ø5 x Ø14x1mm
Flat Washers (4)
Wood Blade Holders
(for use with FP1022, FP1026,
FP1030 blade sets)
Traditional Blade Holders
(for use with Palm, Bamboo,
Wicker blade sets)
NOTE: The illustration shown is not to scale or its actual configuration may vary.
Parts and packings subject to change without notice.
FP20
Long Neck
Pulley
Assembly
FP10
Short Neck
Pulley
Assembly
Figure 2
FP10 (Short)/FP20 (Long) Pulley Assembly and Hardware Parts Identification
Phillips
Screwdriver
Belt
Traditional Blade
Screws, 3/16˝-24 x 3/8˝ (5)
Blade Holder
to Hub Screws
10-32 x ½˝ (5)
NOTE: If you are uncertain of part description, refer to exploded
view illustration. (Figure 2, page 17)
NOTE: Optional Wood Blade Holders (BH20 series) and B4000
wood blades are available for this assembly. Not for Damp
Location usage.
Wood Blade Screws,
3/16˝-24 x ½˝ (7) &
Ø12.5 x Ø5x1 mm
Fiber Washers (7)

6
Electrical and Structural Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and remove
the existing light fixture.
Figure 3
2” Lag Bolt
& Flat Washer
(4 places)
2” Lag
Bolt
& Flat
Washer
(4 places)
▲ WARNING
Turning off wall switch is not sufficent. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and the
ceiling fan must be properly grounded as a precaution
against possible electrical shock. Follow all wiring
instructions carefully. Any electrical work not described
in these instructions should be done or approved by a
licensed electrician.
Lighting Options
Optional lighting fitters and light kits are available, including a single bowl fixture with a maximum of 180 watts and a
variety of four light fixtures with a maximum of 240 watts. Can be only mounted on the motor switch cup. Installation
instructions provided with each light fitter and light kit.
Outlet Box Flush
to Finished
Ceiling
Plywood (¾˝thick min.)
Backing Secured to
Structural Member
INSTALLATION NOTE
It is recommended that each fan and the motor have ¾˝
plywood backing secured to a structural member for
adequate support (Figure 1). A 120 VAC electrical feed,
centered under the motor unit and wired to a 3 speed
control (supplied) is required. The motor unit will not
operate more than 2 pulley/blade assemblies.

7
How to Set Your Switch Cap Remote Receiver
This step is to be completed prior to hanging your motor.
1. Removing the Switch Housing:
Remove the switch housing from the motor by
unscrewing the three screws and unplugging the
connector (Figures 1 & 2).
2. Removing the Receiver Unit:
Carefully, slide the remote Receiver from the Switch Cap
Housing, and locate the code switches on the underside
of the receiver unit (Figure 3).
3. Setting the Receiver Code:
The remote unit has 16 different code combinations.
It may be necessary to test a couple frequency code
settings to improve signal reception and/or eliminate
interference from other remote control household items.
Multiple fans should have different code settings to allow
independent fan control. To set the code, slide code
switches to the same positions as is set on your TR20
transmitter (Figure 3).
4. Installing Receiver in Switch Cap Housing:
Slide remote Receiver into the Switch Cap, connect the
plug from the motor assembly into the socket located in
the receiver unit (Figure 2 & 3).
5. Installing the Switch Cap Housing:
Slide the assembled Switch Cap Housing over the Switch
Cap Base by installing and tightening the three screws
(Figure 1).
Figure 2
▲ WARNING
Check to see that all connections are tight. To avoid
possible electrical shock, make sure that the electrical
wires are completely inside the switch housing and
not pinched between the switch cap base and switch
housing.
Figure 3
If you feel that you do not have enough electrical wiring
knowledge or experience, have your fan installed by a
licensed electrician.
▲ WARNING
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
1. Setting the Code: The remote unit has 16 different
code combinations. To prevent possible interference from
or to other remote units such as garage door openers, car
alarm or security systems, simply change the combination
code in your transmitter and receiver. To set the code,
perform these steps.
•Transmitter: remove battery cover. Press firmly below
arrow and slide battery cover off. Slide code switches to
your choice of up or down position. Factory setting is all
up. Do not use this position. With a small screwdriver or
ball point pen slide firmly up or down (Figure 1). Replace
battery cover on the transmitter.
Figure 1
Remote
Transmitter
Unit Detail
1 2 3 4
ON ECE
ON ECE
How to Set Up Your Remote Control
Figure 1

8
How to Hang and Wire Your Ceiling Fan
1. You will first drill ³⁄16˝pilot holes into the plywood base
or supporting member to prevent splitting or cracking.
Mount the Pulley Assembly on the ceiling with 4 lag bolts
and flat washers (Figure 1a).
2. Drill ³⁄16˝pilot hole located approximately as shown
in Figure 1a & 1b for lag “J” hook. Screw lag hook into
ceiling.
3. Hang motor assembly on lag hook for ease of wiring
fan motor (Figure 1b).
Floor
Ceiling
No
less than
7 ft
14 ft max - motor to head
4 ft min
(13½ ft max - head to head)
Figure 1a
Figure 2
2” Lag Bolt
& Flat Washer
(4 places)
2” Lag
Bolt
& Flat
Washer
(4 places)
Outlet Box Flush
to Finished
Ceiling
Plywood (¾˝thick min.)
Backing Secured to
Structural Member
Figure 1b
CAUTION
Do not connect fan blades until the fan is completely
installed. Hanging fan with blades connected may result
in damage to the fan blades.
INSTALLATION NOTE
The fan must be hung with at least 7’ of clearance from
floor to blade. The maximum overall (belt) length between
motor & pulley is 14´ and the minimum is 4´. (Figure 2)
For two-pulley assembly installation: The maximum
overall distance between two pulley assemblies is 13½´
and the minimum is 5´.
▲ WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
INSTALLATION NOTE
It is recommended that each fan and the motor have ¾˝
plywood backing secured to a structural member for
adequate support (Figure 1). A 120 VAC electrical feed,
centered under the motor unit and wired to a 3 speed
control (supplied) is required. The motor unit will not
operate more than 4 pulley/blade assemblies.
INSTALLATION NOTE
Motor assembly can be mounted at either end of Pulley
assembly or in the middle.

9
How to Hang and Wire Your Ceiling Fan (continued)
4. Connect the green grounding lead from the fan motor
to the supply grounding conductor (this may be a bare
wire or wire with green colored insulation). Securely
connect wires with wire connectors supplied. (Figure 3)
5. Mount retainer to junction box with screws (provided
with your junction box). (Figure 4)
6. Loosen strain relief and pull excess lead wires through
canopy. Re-tighten strain relief.
7. Cut and strip lead wires.
8. Securely connect the white fan motor wire to the
white supply (neutral) wire using wire connector supplied.
Securely connect the black fan motor wire wire to the
black supply wire using wire connector supplied. (Figure
3) After connections have been made, turn leads upward
and carefully push leads into the outlet box, with the white
and green leads on one side of the outlet box and the
black lead on the other side of the outlet box. (Figure 5)
9. After the connections have been made, tighten the lag
bolts to secure fan base assembly to the ceiling, making
sure that the electrical wires are completely inside the
base assembly and not pinched between the base and
the ceiling.
Retaining
Nut
Junction
Box
If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.
Canopy
Strain Relief
Retainer
Figure 4
Figure 3
Figure 5
Junction
Box
Ceiling
Plywood
Base
Motor
Housing
Ceiling Joist
2˝Lag Bolt &
Flatwasher
(4 places)
▲ WARNING
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
▲ WARNING
Check to see that all connections are tight. To avoid
possible electrical shock, make sure that the electrical
wires are completely inside the base housing and not
pinched between the base and the ceiling.

10
Belt Splicing Instructions
Figure 1
Figure 2
Figure 3
Figure 7
Figure 6
Figure 5
Figure 4
1. Wrap the belting around the two pulleys that will
be connected and overlap the belting as shown. Use
the spring clamps provided to hold the belting in place
temporarily. With the clamps remaining in the same
place, grasp both ends of the belting and pull tight. The
clamps should hold the belting together after releasing
the belt. (Figure 1)
2. Punch two holes (approximately 1/8 inch in diameter)
through the overlapping belts, spacing them one inch
apart with the punch tool supplied. (Figure 2)
3. Using the rivets, rivet washers, and the rivet tool
provided, install two rivets. The fl at head of the rivet
must be on the inside of the belt (the side touching the
pulley), while the rivet washer is placed on the outside
of the belt. (Figures 3, 4, & 5)
4. Trim the excess belting as shown. The overlap
should be approximately one to two inches in length.
(Figures 6 & 7)

11
Figure 2
Mounting the Fan Blades
Natural Palm Leaf, Woven Bamboo, Woven Wicker
Blades
1. Lay side “A” of the blade holder on a flat surface with
the inside of the blade holder facing up. This is the side
with the threaded posts and pitched foot (Figure 1).
2. Position the palm leaf, or the woven bamboo or wicker
blade over the blade holder with the threaded posts
showing. Make sure the bottom edge of the blade is fully
seated against the blade holder.
3. Place side “B” of the blade holder on top of the blade,
positioning the holes over the threaded posts.
4. With a Phillips screwdriver, thread both screws into the
posts but do not fully tighten.
5. Prior to final tightening, position the center line of the
blade holder with the center of the end of the blade.
6. Tighten both screws to secure the blade (Figure 1).
Standard Reversible Wooden Blades
1. Mount the wooden blades on the blade holder with
three screws and three fiber washers .
2. Then mount the assembled blade/blade holder onto
the flywheel, secure with flywheel screws.
(Figure 2)
NOTE: Optional Wood Blade Holders (BH20 series) and
B4000 wood blades are available for this assembly. Not
for Damp Location usage.
Side B
Side A
Fan Blade
Reversible
Wooden Blade
Palm Leaf, Woven Bamboo,
or Wicker Blade
NOTE: Blade detail omitted for clarity.
Figure 1
CAUTION
Do not connect fan blades until the fan is completely
installed. Hanging fan with blades connected may result
in damage to the fan blades.

12
Figure 2
Figure 3
MAIN FUSE BOX
Figure 1
For illustrative purposes only-not
intended to cover all types of controls
Operating Instructions-Remote Control
2. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box (Figure 2).
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until the blades are in place. Noise and
fan damage could result.
WARNING
Do not operate this fan with a variable (Rheostat) wall
controller or dimmer switch. Doing so could result in
damage to the ceiling fan's remote control unit.
WARNING
1. IMPORTANT: Using a full range dimmer switch
(not included) to control fan speed will damage the fan.
To reduce the risk of fire or electrical shock, do not use
a full range dimmer switch to control the fan speed.
(Figure 1)
3. Operating & Using Hand-held Remote (Figure 3):
Install two piece of 3 volt battery (If not using for long
periods of time, remove battery to prevent damage to
store hand-held remote). the hand-held remote away from
excess heat or humidity.
• HI Push Button – high fan speed
• MED Push Button – medium fan speed
• LOW Push Button – low fan speed
• REV Push Button – toggles airflow direction
• Push Button – fan off
• Light Push Button – on/off, hold for infinite light level
REMOTE
3V, CR2032
BATTERY
(2 PCS)
CONTROL
ECE

How to Install Your Remote Control (Option #3)
1. Drill the two 1/4” holes in wall and use the M6 plastic
anchor pushed into the holes. Install the control bracket
with two #3- 1” self tap screws. Push the four plastic plug
to cover the screw holes. (Including in the control
packaging). (Figure 1)
Figure 1
How to Install Your Remote Control (Option #1)
How to Install Your Remote Control (Option #2)
1. Unthread two screws from the wall switch plate.
(Figure 1)
2. Install the control bracket with two #6-32x 1” screws.
And push the four plastic plug to cover the screw holes.
(Included in the control packaging). (Figure 2)
1. Unthread two screws from the wall switch plate.
(Figure 1)
2. Install the control bracket with two #6-32x 3/4” screws.
And push the four plastic plug to cover the screw holes.
(Included in the control packaging). (Figure 2)
Figure 1 Figure 2
Figure 1 Figure 2
13

Maintenance
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed. When cleaning, use only a
soft brush or lint free cloth to avoid scratching the finish.
Abrasive and/or non-abrasive cleaning agents are not
required and should be avoided to prevent damage to
finish.
Blade Cleaning
Periodic light dusting of the Palm Leaf, Woven Bamboo,
Wooden, or Wicker blades is recommended. A feather
duster will work best.
Avoid using water, cleansers, or harsh rags, which can
warp and ruin the blades.
CAUTION
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of electrical shock.
14
Trouble Shooting
▲ WARNING
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
Trouble Probable Cause Suggested Remedy
1. FAN WILL NOT START 1. Fuse or circuit breaker blown.
2. Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
3. Dead battery in remote control.
4. Control receiver frequency switches not set.
1. Check main and branch circuit fuses or circuit
breakers.
2. Check line wire connections to fan and switch wire
connections in the switch housings.
CAUTION: Make sure main power is turned off !
3. Replace with fresh battery.
4. Make sure hand-held remote and receiver frequency
switches match.
2. FAN SOUNDS NOISY 1. Loose screws in motor housing.
2. Screws securing fan blade are loose.
3. Motor noise caused by solid state variable speed
control.
4. Pulley set screw loose.
5. Rivets (on belt) make clicking sound.
1. Check to make sure all screws in motor housing are
snug (not over-tight).
2. Check to make sure the screws which attach the fan
blade to the are tight.
3. Some fan motors are sensitive to signals from
solid-state variable speed controls. Solid-state controls
are not recommended, choose an alternative control
method.
CAUTION: Make sure main power is turned off !
4. Tighten set screw securely.
5. Not considered a defect.
3. FAN WOBBLES
EXCESSIVELY
1. Fan / Motor base lag bolts on the ceiling is loose.
2. Blade holders not seated properly.
1. Tighten lag bolts securely.
2. Check to be sure the fan blade holders seat firmly
and uniformly to the surface of the hub. If holders are
seated incorrectly, loosen the screws retighten.

18
19
15
20
22
22 Set Screw 5/16-18 x 3/8 W/Locktite
22
1
2
3
4
7
5
6
10
9
11
13
14
12
Ref. # Description Part #
FMA1280
1 Switch Cap Assembly PSW50
2 Control Receiver CR1280
3 Nut
4 Flat Washer
5 Switch Cap Base
6 Motor Pulley
7 Motor Housing
8 M/S, Washer Hd, 3/16-24 x 3½”, Black
9 Motor
10 Hex Nut, 3/16-24 x 4mm (4)
11 Lock Nut, Nylon Insert, 3/16-24 x 5mm (4)
12 Canopy Assembly SPCA1280
HDW1280RV
16 Rivets with Rivet Washers
HDW1280LP
13 Lag Bolt, ¼x 2”, Black (4)
14 Flat Washer, ¼”, Black (4)
20 “J” Hook
21 Wire Connectors (3)
15 Hand-held Remote
TR20WH
17 Clamps (2) P128015
18 Rivet Tool P128005
19 Punch Tool P128010
8
21
16
17
Figure 1
15
NOTE: The illustration shown is not to scale or its actual configuration may vary. Wires partially removed for clarity.
Non-Serviceable Items
Insert FINISH CODES (Refer to fan model number located on fan assembly)
Exploded-View Drawing
The Brewmaster®Motor FP1280**
Parts List
Brewmaster Motor Assembly
Belt Rivet Parts Bag Containing:
Loose Assembly Parts Bag Containing:
Miscellaneous Tools & Control

16
Ref. # Description Part #
Pulley Assembly FP10 /FP20
1 Pulley with set screw
2a Short Frame (Short model)
2b Long Frame (Long model)
3 Cushion, Bearing, Black
4 Bearing
5 Shaft
6 Hub
7 Blade Holder (2) (Wooden Blades only) P1212
8 Bag, BH to Hub Screws,10-32 x ½˝,Black (5) HDWFP10HB
9 Bag, Lag Bolt, ¼˝x 2˝, Black, w/washers (4) HDWFP10LG
10 Bag, Wood Blade Screw,3/16˝-24 x ½˝,Black (7),
w/Fiber Washers (7) HDWFP10WB
11 Bag, Trad. Blade Screw,3/16˝-24 x 3/8˝,Black (5) HDWFP10TB
12 Blade Arm Cover (2) P3220
13 Trad. Blade Holder (2) (Palm, Bamboo, Wicker) P3210
14 Belt (one 30 ft roll) BM30
15 Phillips Screwdriver P3295
How to Order Parts
When ordering repair parts, always
give the following information:
• Part Number
• Part Description
• Fan Model Number
Contact your retail store for repair parts.
Parts List
Insert FINISH CODES (Refer to fan model number located on fan assembly)
Non-Sevicable Items

NOTE: The illustration shown is not to scale or its actual configuration may vary.
Exploded-View Drawing
8
The Brewmaster®Pulley Assembly Pack
FP10__ (Short) / FP20__ (Long)
17
7
11
6
5
3
4
2a
2b
1
3
4
14
9
8
9
10
11
12
13
10
Figure 2
15

10983 Bennett Parkway
Zionsville, IN 46077
Toll Free [phone]
FAX [phone]
Outside U.S. call [phone]
Visit Our Website www.fanimation.comCopyright 2015 Fanimation 2015/01 V.01

Modelo N.º FP10 / 20 Fan de la serie
Modelo N.º FP1280 El motor de la serie
The Brewmaster®
Ventiladores de techo con impulsión de correa
Apropiado para su uso con controles de velocidad de estado sólido
ADVERTENCIA: Soporte directamente desde la estructura del edificio.
Cuello Largo FP20
Cuello corto FP10
Conjunto del motor
MANUAL DEL PROPIETARIO
LEA Y GUARDE ESTAS INSTRUCCIONES
Peso neto 6.8kg (15lb)
Peso neto 6.8kg (15lb)
Peso neto 5.0kg (11lb)

ADVERTENCIA: Monte a una caja de salida aceptable para apoyo de los aficionados.
(1) Este equipo no causará interferencias perjudiciales y (2) este equipo tolerará cualquier interferencia recibida, incluidas las
interferencias que puedan provocar un funcionamiento no deseado. Si el radiador intencional puede ser clasificado como un
dispositivo digital de clase B o un periférico del ordenador, entonces se deberán incluir los siguientes o equivalentes:
Nota: Tras someterlo a las pruebas correspondientes, se ha determinado que este equipo cumple con los límites establecidos para
dispositivos digitales de Clase B de conformidad con la parte 15 de la Normativa FCC. Estos límites se han establecido con el objetivo
de aportar una protección razonable contra interferencias perjudiciales cuando el equipo se utiliza en el hogar. Este equipo genera,
utiliza y puede emitir energía de radiofrecuencia y, a menos que se instale y se utilice de acuerdo con el manual de instrucciones, puede
provocar interferencias perjudiciales en las comunicaciones por radio y televisión. Si el equipo produce interferencias perjudiciales en la
recepción de radio o televisión, lo cual puede probarse encendiendo y apagando el equipo, se recomienda al usuario corregir dichas
interferencias tomando una o varias de las siguientes medidas:
- Modificar la orientación o ubicación de la antena de recepción;
- Aumentar la separación entre el equipo y el receptor;
- Conectar el equipo a una toma de corriente o circuito diferente al del receptor;
Consulte al distribuidor o a un técnico especialista de radio o TV para obtener más ayuda.
Nota: Para un dispositivo digital de clase A, la declaración de 15. 105(a) debe ser incluida cuando sea apropiada para el dispositivo en
cuestión.
8. En lo que respecta a las conexiones de suministro, si el conductor del ventilador está identificado como conductor con conexión a tierra,
se le debe conectar a un suministro de electricidad con conductor de puesta a tierra. Si el conductor del ventilador está identificado
como conductor que no es de puesta a tierra, se le debe conectar a un suministro de electricidad con conductor sin puesta a tierra.
Si el conductor del ventilador está identificado para equipos de puesta a tierra, se le debe conectar al conductor de equipos de puesta
a tierra.
GARANTÍA LIMITADA DE POR VIDA DEL MOTOR - Si se produjera una falla en alguna de las partes del motor de su ventilador debido1. a un defecto en los materiales o en la fabricación durante el tiempo de vida del comprador original, Fanimation proporcionará la pieza de
repuesto sin cargo una vez que el ventilador defectuoso sea devuelto a nuestro centro de servicios nacional. Se requiere comprobante de
venta. El cliente se hará responsable de todos los gastos de remoción o reinstalación y envío del producto para reparaciones o sustitución.
GARANTÍA DE MANO DE OBRA DEL MOTOR POR UN AÑO - Si el motor de su ventilador fallara antes de cumplirse un año a partir del2. momento de su compra original debido a defectos en los materiales o en la fabricación, se le efectuará la reparación del mismo sin cargo
en nuestro centro de servicios nacional. El comprador se hará responsable de los gastos de mano de obra luego del período de un año.
El cliente se hará responsable de todos los gastos de remoción o reinstalación y envío del producto para reparaciones o sustitución.
Si otra pieza del ventilador fallara dentro del período de un año a partir de la fecha de compra original debido a un defecto en los3. materiales o en la fabricación, repararemos o sustituiremos, según creamos conveniente, la pieza defectuosa sin cargo alguno en
nuestro centro de servicios nacional.
GARANTÍA LIMITADA DE POR VIDA
Se extiende al comprador original de un ventilador Fanimation
Instrucciones de seguridad importantes
ADVERTENCIA: Siga estas instrucciones para prevenir incendios, descargas eléctricas y lesiones personales graves.
Lea el manual del propietario y la información de seguridad antes de instalar su nuevo ventilador. Observe los diagramas de1.
ensamblaje adjuntos.
Antes de llevar a cabo el mantenimiento o la limpieza de la unidad, desconecte la electricidad en el panel de servicio y bloquee los2.
medios de desconexión del mismo para evitar que se active accidentalmente. Si no se pueden bloquear los medios de desconexión
del servicio, coloque un dispositivo de advertencia, como una etiqueta, en el panel de servicio.
Tenga cuidado con la estructura y las aspas del ventilador cuando limpie, pinte o trabaje cerca del mismo. Desconecte siempre la3.
electricidad del ventilador de techo antes de llevar a cabo el mantenimiento.
No coloque nada en las aspas del ventilador cuando éste se encuentra en funcionamiento.4.
No accione el conmutador inversor hasta que las aspas del ventilador se hayan detenido por completo.5.
Instrucciones de seguridad adicionales
Para evitar posibles descargas eléctricas, asegúrese de que la electricidad esté desconectada en la caja de fusibles antes de realizar1.
la instalación eléctrica, y no haga funcionar el ventilador sin las aspas.
Todos los procedimientos de conexión eléctrica e instalación deben cumplir con los Códigos eléctricos nacionales (ANSI/NFPA2.
70-1999) y Códigos locales. El ventilador de techo debe estar conectado a tierra a fin de prevenir posibles descargas eléctricas. La
instalación eléctrica debe ser llevada a cabo o aprobada por un electricista autorizado.
Las aspas del ventilador deben instalarse por lo menos a 2 m (7 pies) del suelo, a fin de evitar un contacto accidental con las mismas.5.
3. La base del ventilador debe estar adecuadamente instalada y sea capaz de soportar de forma fiable al menos 100 libras (el ventilador
y los accesorios no exceden las 35 libras o 16 kg). Las cajas de electricidad no son adecuadas para el soporte del ventilador. Consulte
la página 24 del manual del propietario para ver los requisitos de soporte. Consulte un electricista cualificado si tuviera alguna duda.
4. PRECAUCIÓN: Para reducir el riesgo de daños personales, instale la base del ventilador en una viga o parte de la estructura utilizando
el equipo suministrado con su ventilador.
Siga las recomendaciones sobre el método correcto de instalación eléctrica de su ventilador de techo. Si no posee la experiencia o6.
los conocimientos eléctricos adecuados, contrate a un electricista autorizado para instalar el ventilador.
Apto para usar con controles de velocidad de estado sólido.7.
ADVERTENCIA: Este producto está diseñado para ser usado sólo con las piezas suministradas o los accesorios indicados
específicamente para el mismo. Si utiliza piezas o accesorios que no están indicados para su uso con este producto, podría
sufrir lesiones personales o dañar el ventilador. ADVERTENCIA: Este producto está diseñado para ser usado sólo con las piezas
suministradas o los accesorios indicados específicamente para el mismo. Si utiliza piezas o accesorios que no están indicados para su
uso con este producto, podría sufrir lesiones personales o dañar el ventilador.
ADVERTENCIA: Para reducir el riesgo de lesiones personales, no doble los soportes de las aspas (borde o soporte de aspas) al instalar
los soportes, balancear las aspas o limpiar el ventilador. No coloque objetos extraños entre las aspas del ventilador en funcionamiento.
ADVERTENCIA: Para reducir el riesgo de descargas eléctricas, este ventilador se debe instalar con un control/interruptor de pared
ADVERTENCIA:
ADVERTENCIA: Soporte directo desde la estructura del edificio.
Para reducir el riesgo de incendios o descargas eléctricas, este ventilador solo debería ser utilizado con la pieza de
control de velocidad del ventilador Nº UC7067RY fabricada por Rhine Electronic Co., Ltd.
aislado.
ADVERTENCIA: No utilice este ventilador con un controlador variable de pared (Rheostat) o un regulador de intensidad. Si lo hiciera
podría dañar la unidad del mando a distancia del ventilador de techo.