Feig Electronic ID ISC.LR.WS-A User manual

INSTALLATION
final –public (B)
2018-02-15 –M80211-0e-ID-B.docx
ID ISC.LR.WS-A Wiegand Switch (4955.000.00)
Functional Description and Installation

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 2 of 18
M80211-0e-ID-B.docx
Note
Copyright 2018 by
FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg
Tel.: [phone]
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this manual may be
changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are
forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved
in the event of the grant of a patent or the registration of a utility model or design.
Composition of the information in this manual has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC
GmbH does not give any guarantee promise for perfect function in cross environments and does not give
any guaranty for the functionality of the complete system which incorporates the subject of this document.
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed
with components and testing methods for a level of reliability suitable for use in or in connection with surgical
implants or as critical components in any life support systems whose failure to perform can reasonably be
expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application
designer must take reasonably prudent steps to protect against system failures.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this
manual and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does
not convey any license under its patent rights nor the rights of others.

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 3 of 18
M80211-0e-ID-B.docx
Contents
1. Abbreviated terms 4
2. Safety Instructions / Warning - Read before start-up ! 5
3. Characterization ID ISC.LR.WS-A 6
3.1. Scope of delivery...............................................................................................................7
3.2. Reader Support..................................................................................................................7
4. Dimensions 8
5. System Architecture 9
6. Connector description of the Wiegand Switch 10
6.1. Power Supply................................................................................................................... 11
6.2. Inputs ...............................................................................................................................12
6.3. Wiegand Outputs D0, D1 (5V TTL).................................................................................. 13
7. DIP-Switch settings 14
8. Indicators LED’s 15
9. Technical Data 16
10. Wiring and Configuration Examples 17
10.1. ID ISC.LRU1002.............................................................................................................. 17
10.1.1. Wiring.......................................................................................................................17
10.1.2. Configuration............................................................................................................18

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 4 of 18
M80211-0e-ID-B.docx
1.
Abbreviated terms
Ant Antenna
D0 Data-0
D1 Data-1
GND Ground
IN Input
I/O Input/Output
OUT Output
REL Relay
RFID Radio-Frequency Identification
UHF Ultra High Frequency

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 5 of 18
M80211-0e-ID-B.docx
2.
Safety Instructions / Warning - Read before start-up !
The device may only be used for the intended purpose designed by for the
manufacturer.
The installation manual should be conveniently kept available at all times for each user.
Unauthorised changes and the use of spare parts and additional devices which have not
been sold or recommended by the manufacturer may cause fire, electric shocks or
injuries. Such unauthorised measures shall exclude any liability by the manufacturer.
The liability-prescriptions of the manufacturer in the issue valid at the time of purchase
are valid for the device. The manufacturer shall not be held legally responsible for
inaccuracies, errors, or omissions in the manual or automatically set parameters for a
device or for an incorrect application of a device.
Repairs may only be executed by the manufacturer.
Installation, operation, and maintenance procedures should only be carried out by
qualified personnel.
Use of the device and its installation must be in accordance with national legal
requirements and local electrical codes .
When working on devices the valid safety regulations must be observed.

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 6 of 18
M80211-0e-ID-B.docx
3.
Characterization ID ISC.LR.WS-A
The Wiegand Switch is an additional interface device which allows you to route the Wiegand signal
of a FEIG RFID reader to two different input channels of an access control panel.
Switching between the output channels of the Wiegand Switch is controlled by the readers relay.
The readers relay is switched on or off in dependency of a read event on a particular antenna.
This offers the possibility to control two neighboring gates e.g. in a vehicle access control applica-
tion with just one reader. This can either be an entry and an exit, two entry lanes or two exit lanes.
Multiple antennas can be used per lane.
Figure 1: Examples for control of two lanes with one reader ID ISC.LRU1002 (V2)
The Wiegand Switch can be also used if the Wiegand signal quality of other reader types is not
sufficient for the connected Access Control Panel.

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 7 of 18
M80211-0e-ID-B.docx
3.1.
Scope of delivery
The delivery contains the following parts:
Table 1: Product order information
Part Number
Product Name
4955.000.00
ID ISC.LR.WS-A Wiegand-Switch
3.2.
Reader Support
The Wiegand Switch can be used with the following FEIG devices:
Table 2: Supported Reader types if Wiegand Switch is used for two lanes
Part Number
Product Name
Commend
4127.001.00
4128.001.00
ID ISC.LRU1002-EU (V2)
ID ISC.LRU1002-FCC (V2)
Useable from firmware version 1.00
3548.000.01
3549.000.01
ID ISC.LRU3000-EU
ID ISC.LRU3000-FCC
If required please contact
[e-mail]
3551.000.01
3550.000.01
ID ISC.LRU3500-EU
ID ISC.LRU3500-FCC
Table 3: Supported Reader types if Wiegand Switch is used for one lane to get an improved 5 V
TTL Wiegand signal
Part Number
Product Name
Commend
4127.000.00
4128.000.00
ID ISC.LRU1002-EU
ID ISC.LRU1002-FCC
Can be used to get an improved 5 V
TTL Wiegand signals for an easy
adaption of the reader to a Wiegand
Controller
3548.000.01
3549.000.01
ID ISC.LRU3000-EU
ID ISC.LRU3000-FCC
3551.000.01
3550.000.01
ID ISC.LRU3500-EU
ID ISC.LRU3500-FCC
3620.000.00
ID ISC.LR2500-A
3618.000.00
3619.000.00
ID ISC.LRM2500-A
ID ISC.LRM2500-B

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 8 of 18
M80211-0e-ID-B.docx
4.
Dimensions
The ID ISC.LR.WS-A is designed for DIN hat rail mounting (according to DIN EN 50 022) and is
therefore especially suited for use in industrial housings.
22,5 mm
90 mm
99 mm

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 9 of 18
M80211-0e-ID-B.docx
5.
System Architecture
The Wiegand Switch is powered by a an external supply voltage of 12 up to 24 V DC. This can be provided
either by an external power supply or by the DC pin of the readers I/O connector (depending on used
reader).
The Wiegand Output of the reader is connected to the Wiegand Input of the Switch. The Wiegand Outputs of
the Switch are connected to different inputs at an Access Control Panel.
The output of the Wiegand Switch is controlled by a switching signal. The switching signal can be generated
by the readers relay output. The on/off switching of the relay in dependency of a read event on a particular
antenna can be configured in the reader settings (see: 10.1.2. Configuration).
If the reader relay is switched off (default state) the Wiegand Switch uses its Wiegand Output A. If the relay
is switched active the Wiegand signal will be routed to Wiegand Output B.
Figure 2: System Architecture

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 10 of 18
M80211-0e-ID-B.docx
6.
Connector description of the Wiegand Switch
Figure 3: Available Connectors gives an overview on the different connectors of the Wiegand
Switch, the reader and the used Access Control Panel.
Figure 3: Available Connectors
Figure 4: Connector overview X1 –X4
X2
X1
X4
X3

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 11 of 18
M80211-0e-ID-B.docx
6.1.
Power Supply
The supply voltage of 12-24 V DC must be connected to connector X1 of the Wiegand Switch.
Figure 5: Pin Assignment at connector X1
Table 4: Pin assignment at connector X3
Pin
Signal
X1-GND
Ground
X1-VCC
12-24 V DC
X1

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 12 of 18
M80211-0e-ID-B.docx
6.2.
Inputs
The Output signals from the reader are connected to connector X1 and X2 of the Wiegand Switch.
Figure 6: Pin Assignment at connector X1
Table 5: Pin assignment at connector X1 and X2
Pin
Signal
X1-Relay No
Switching signal of the relay
X1- Relay COM
X2-OUT1 E/D0
Data-0 Signal of the readers Wiegand Output
X2-OUT1 C/ 5V
5 V DC Signal to drive the outputs of the reader
X2-OUT2 E/D1
Data-1 Signal of the readers Wiegand Output
X2-OUT2 C/ 5V
5 V DC Signal to drive the outputs of the reader
X2
X1

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 13 of 18
M80211-0e-ID-B.docx
6.3.
Wiegand Outputs D0, D1 (5V TTL)
The input signals of the external access controller are connected to connector X3 and X4 of the
Wiegand Switch.
Figure 7: Pin Assignment at connector X3 and X4
Table 6: Pin assignment at connector X2
Pin
Signal
X3-A D0
D0 at Input 1 of the Access Controller (5V TTL)
X3-A D1
D1 at Input 1 of the Access Controller (5V TTL)
X3-GND
Common Ground
X4-B D0
D0 at Input 2 of the Access Controller (5V TTL)
X4-B D1
D1 at Input 2 of the Access Controller (5V TTL)
X4-GND
Common Ground
X4
X3

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 14 of 18
M80211-0e-ID-B.docx
7.
DIP-Switch settings
The Wiegand Switch is equipped with two DIP-Switches . This DIP-Switch need to be set depend-
ing on the used reader type.
For getting access to the DIP-Switches the Wiegand Switch need to be opened.
Figure 8: Position of the DIP-Switch
Table 7: Jumper setting
Jumper position
Action
Default Setting
Use with ID ISC.LRU1002 (V2) only
(EU: 4127.001.00; FCC: 4128.001.00)
Use with ID ISC.LRU3x00 and ID ISC.LR(M)2500 and
ID ISC.LRU1002 (EU: 4127.000.00; FCC: 4128.000.00)
NOTE:
The setting of the DIP Switch 1-2 should always be set in pairs
DIP-
Switch
Push latch to open
Push latch to open

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 15 of 18
M80211-0e-ID-B.docx
8.
Indicators LEDs
The Wiegand Switch has two green LEDs which indicates the active Wiegand output A or B.
Figure 9: shows the position of the two green LEDs

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 16 of 18
M80211-0e-ID-B.docx
9.
Technical Data
Technical Data
Housing
Polyamide
Colour
RAL7035 (light grey)
Dimensions
99 mm x 90 mm x 22,5 mm (H x L x W)
Weight
approx. 90 g
Power Supply
12…24 V DC (+/-20 %)
Current Consumption
typ. < 80 mA
Output voltage
5V TTL (D0, D1)
Supported Reader
Two lane support:
ID ISC.LRU1002 (V2)
Wiegand Signal improvement:
ID ISC.LRU1002, ID ISC.LRU3000, ID ISC.LRU3500,
ID ISC.LR2500
Indicator
2 green LED; indicates the active Wiegand output
Other Features
Housing for DIN Hat Rail Mounting
Temperature
- Operation
- Storage
-25 °C up to +55 °C
-40 °C up to +85 °C
Humidity
5 % up to 95 % (non-condensing)
Vibration
EN 60068-2-6
10 Hz up to 150 Hz: 0,075 mm / 1 g
Shock
EN 60068-2-27
Acceleration: 30 g
Applicable Standards
- EMC
- Safety
EN 301 489
EN 32 368

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 17 of 18
M80211-0e-ID-B.docx
10.
Wiring and Configuration Examples
10.1.
ID ISC.LRU1002
10.1.1.
Wiring
Figure 10: Wiring Example for ID ISC.LRU1002

IDENTIFICATION
Installation
Wiegand Switch
FEIG ELECTRONIC GmbH
Page 18 of 18
M80211-0e-ID-B.docx
10.1.2.
Configuration
Figure 11: Example for relay settings in the reader configuration shows an example for possible
settings in the reader configuration. In that scenario two antennas are connected to the reader.
Each antenna is used to control a separate lane. If a transponder is detected by antenna 1 the re-
lay of the reader stays off. Data is transmitted by Output A of the Wigand Switch to the Access
Controller. If a transponder is read by antenna 2 the relay output of the reader is switched on. Data
is transmitted by Output B of the Wiegand Switch to the Access Controller.
Figure 11: Example for relay settings in the reader configuration
NOTE:
The relay “Setting Time” need to be set to (00001 x 100 ms)
Table 8: Settings for 2 gates with one antenna per lane
Gate
Antenna assignment
Read Event Activation
Output Wiegand Switch
1
ANT1
False
OUT A
2
ANT2
True
OUT B
Table 9: Settings for 2 Gates with 2 antennas per lane
Gate
Antenna assignment
Read Event Activation
Output Wiegand Switch
1
ANT1
False
OUT A
1
ANT2
False
OUT A
2
ANT3
True
OUT B
2
ANT4
True
OUT B