Fencee MX10 User manual

1
EN
User
manual
REMOTE MONITORING
OF FENCE PARAMETERS
Wireless RF connection with the Gateway.
IT DOES NOT NEED A SIM CARD
No additional operating costs.
www.fencee.eu
Electric fencing
WORKS ONLY IN CONJUNCTION WITH:

2
Thank you for purchasing the MX10 Monitor from VNT electronics s.r.o.
The device complies with the safety regulations according to the valid
law as well as the relevant EU regulation (CE).
The device complies with the Council of Europe Directive 2014/53/EC, meets the requirements
of the General License of the Czech Telecommunication Oce according to the general authorization
No. VO-R/10/05.2014-3, and it also complies with the below requirements of the standards and regulations
applicable to this type of equipment:
2014/35/EU I2014/30/EU IR&TTE EN300-220 a EN 61000-6-3:2007 + A1:2011
ETSI EN 301 489-1 V1.9.2 I ETSI EN 301 489-3 V1.6.1 I ETSI EN 300 220-2 V.2.4.1
ETSI EN 60950-1 ed.2:2006 /A1:2010 /A11:2009 /A12:2011 /A2:2014/Opr.1:2012 EN 62479:2010
We recommend that you read this manual carefully
before using the device and keep it for future reference!
CONTENT
1introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2Overview of the main benets of the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3Technical parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5Description of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6Description of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7Pairing the Monitor with the GATEWAY GW10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8Connection with GATEWAY GW10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
9Installing the Monitor on a fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10 Troubleshooting - possible fault sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3
1. INTRODUCTION
Use this device to ensure better protection of your animals and land.
Local conditions and circumstances always aect the function of the device and therefore
we cannot guarantee complete protection against breach of the fence. The energizer
manufacturer does not warrant that there will be no breakdown of the fence installation and
does not guarantee that animals cannot run away. The installation of a fence should increase
the safety of the animals in the fence system or protect the land.
Please follow the instructions for use of this device.
Important Notice
•Switch off the electric fence before carrying out any work on the energizer or fence.
•Read the Safety Instructions carefully.
•When installing, make sure that you observe all safety regulations.
•Use only original spare parts.
2. OVERVIEW OF THE MAIN BENEFITS OF THE MONITOR
•LED indication
•Audible indication
•No SIM Card required
•Magnet controlled
•Possibility of connecting an external antenna
•Up to 6 Monitors per fence system and Gateway can be connected
4. PACKAGE CONTENTS
•MX10 Monitor
•Two C-LR14 batteries
•Magnet with a string
•Earthing pin
•Earthing cable for grounding
•Connecting cable to the fence system
•Antenna
•2 pcs plastic cable tie for mounting on a post
3. TECHNICAL PARAMETERS
•Range with basic antenna up to 10 km (included)
•Possibility of connecting an external antenna
(extension cable 2 m or 10 m - range increase up to 30 km)
•RF transmission frequency - 869.525 MHz /22 dBm
•Power battery: 2 × C-LR14
•Dimensions: 78 × 144 × 42 mm
•Weight: 325 g

4
5. DESCRIPTION OF THE DEVICE
•The Monitor MX10 is used to measure voltage anywhere in your fence system.
•Up to 6 MX Control Monitors can be paired on one Gateway and thus divide the fence
system into several zones. Everything then communicates with the central Gateway and
the energizer of the fencee power DUO RF PDX series (it is not part of the Monitor package).
•Using radio frequency technology, it transmits the measured data wirelessly to the central
Gateway, where the values are shown on the display.
•In the event of a voltage drop at the measured point below the set limit, an alarm is sent
and signalling to the Gateway immediately notifies the user of the fault.
Figure 1: Description of the device
SMA connector for
antenna connection
Magnetic target
LED diode
Earthing connector
Connector for
connection to the fence

5
Inserting the batteries
•Unscrew the screws and open the cover on the back of the Monitor.
•Insert two C-LR14 batteries according to the instructions in the plastic cover.
•Return the cover to its original position and tighten the screws firmly.
Figure 2: Back sice of the device
2 × C-LR14
An opening
for the cable tie.
An opening
for the cable tie.

6
6. DESCRIPTION OF CONTROLS
Power supply
The Monitor is powered by two C-LR14 batteries, which must be inserted through the back
cover and the correct polarity must be observed. It is recommended to install alkaline
batteries for longer life. The battery status is indicated in the Gateway as a percentage.
Battery life is about 1 year.
Control
The device is controlled by the included magnet, which must be attached to the target on
the side of the MX10 Monitor. When the magnet approaches, the status of the Monitor is
indicated by an LED diode:
Red = o
Green = on
If no LEDs light up, the batteries need to be checked and replaced.
Switching on
Place the magnet on the target for about two seconds.
The Monitor rst beeps and lights up the red indicator LED. Subsequently, the Monitor will
ash green and beep 3 times. The Monitor is now on and indicates its ON status by regular
ashing green LED. When the Monitor is ON, it indicates its activity for a limited time of
2 minutes to save battery power.
Shutdown
By bringing the magnet closer to the target for about two seconds.
The Monitor rst beeps and lights up the green indicator LED.
Then the Monitor will ash red and beep twice.
The Monitor is now turned o.
You can check the status at any time - by bringing the magnet
closer to the target for <1s. The colour of the LED indicates the
status: red = off, green = on.
TIP:

7
7. PAIRING THE MONITOR WITH THE GATEWAY GW10
First, the MX10 Monitor must be paired with the Gateway in order to display the measured
data. Pairing is performed by the following steps:
1Place the Monitor and Gateway next to each other, up to a maximum distance
of approx. 30 cm.
2The Monitor must be turned o.
3Attach the magnet to the Monitor target for> 3 s.
4The green and red LEDs on the Monitor will start ashing simultaneously.
5Now it is necessary to trigger the pairing mode on the Gateway too.
– description is provided in the Manual for GATEWAY GW10
6Upon successful pairing, the Monitor beeps and ashes green.
At the same time it also automatically shuts o so as not to trigger the alarm
immediately, because it is not connected to the fence yet and has no voltage.
It is displayed on the Gateway with a value of 0 kV.
7The Monitor is now paired and can be installed on the fence system in the required
measuring point.
The Monitor can only be paired to one Gateway - after pairing with
another Gateway , the previous device will be deleted. The pairing
mode ends automatically after 1 minute or it can be interrupted by
applying a magnet to the target.

8
8. CONNECTION WITH GATEWAY
The Monitor measures each pulse in the fence system and sends the values to the Gateway
every 15 minutes. If a voltage lower than the set limit is measured , data is sent to the
Gateway immediately and an alarm is triggered.
Setting the low voltage alarm level on the fence system
The 3 kV limit is set at the factory. The user can freely adjust this value in the Gateway (see
instructions for the Gateway). If the alarm limit on the Gateway is changed, it will not take
eect in the Monitor until the next time new data is received, i.e. in a 15 min cycle.
Low battery alarm
The Monitor‘s low battery is indicated on the Gateway when it drops below 10%.
We recommend replacing it within 2 weeks at the latest.
Display of the paired Monitor on the Gateway and all available information about
a specific device.
DETAILED SCREEN
Signal level between
Monitor and Gateway
Fence voltage
value [kV]
Current set
value for
triggering
an alarm [kV]
Time since
last data
transfer
MX Monitor battery
voltage status [%]
Type
of device
Figure 3: Displaying the paired Monitor on the GATEWAY GW10 display

9
9. INSTALLING THE MONITOR ON A FENCE
After pairing the Monitor with the Gateway, it is possible to place the Monitor in the desired
location of measurement on the fence system.
Before installation, it is necessary to turn o the energizer, in order to ensure safe handling.
We install the Monitor as shown in Figure 4.
After installation, it is possible to turn on the energizer and turn on the Monitor.
Placement rules:
The Monitor can be installed outdoors in an fence system, it is resistant to normal weather
conditions.
The Monitor can be easily installed with cable ties.
Never place the Monitor on the ground - in a humid or wet environment.
Never expose the Monitor to a continuous stream of water.
Figure 4: Connecting the Monitor to the fence system
For a better signal and connection within 30 km
it is possible to use an external antenna.
TIP:

10
Standard installation
Fence system divided into zones. When the voltage drops on a particular Monitor, you
can easily identify the zone and locate the problem.
Installation examples
4
1
2
3
TIP: Place the Monitor where voltage monitoring is required (entrance
to the fence system) or where frequent problems can be expec-
ted, e.g. with vegetation, by the forest, by the water.
Figure 5: Standard installation

11
Installation at the entrance to the fence system
Installation for easy identication of the fence system with a non-functional fence.
FENCE 1 FENCE 2 FENCE 3
Installation at the entrance to the fence system and problem areas
Installation for easy identication of the fence with a non-functional fence. Or places
where problems may occur more often, e.g. near the forest, near water, in places with
denser vegetation.
FENCE 1 FENCE 2
1 2 3
Figure 6: Installation at the entrance to the fence system
Figure 7: Installation at the entrance to the fence system and in problem areas
1
2
34
5

12
9High-voltage connecting cable
10 Conductor
11 Line connector
12 Fixed post
1RF energizer
2Gateway GW10
3External RF antenna
4External alarm
Figure 8: Monitor, Gateway and fence connection
5Monitor MX10
6Earthing cable
7Anticorrosive earthing rod
8Lightning diverter
11.2 kV
BAT 12,6 V
ALARM 3kV
6
7
811
9
10
15
16
12
13
17
Control • Check • Keep informed
WORKS ONLY IN CONJUNCTION WITH:

13
14
13 Tensioner
14 Insulators
15 Warning sign
16 Gate
17 Insulator of gate Table 1:
Description of individual parts of the connection
10.8 kV
BAT 12.2 V
ALARM 3 kV 10,5 kV
BAT 100 %
ALARM 3kV
GAT E WAY GW10
Monitor
MX10
External
Antenna
2
4
3
5
7
8
7
13
11.2 kV
BAT 12,6 V
ALARM 3kV

14
11. WARRANTY
In addition to the statutory warranty, we provide a warranty in accordance with the
following conditions:
•The warranty begins on the day of purchase. Warranty claims are recognized solely upon
presentation of the receipt from the purchase of the product. Warranty repair is free, or we
reserve the right to deliver similar equipment of the same value.
•The warranty is valid if used correctly according to the instructions for use. It expires if there
are interventions by unauthorized persons and when using spare parts other than from the
producer.
•All failures resulting from defects in materials or workmanship will be rectied at the
discretion of the manufacturer either by repair or free replacement of the device.
•When delivering spare parts or providing repair, the warranty period of the original
product is not extended.
•The duration of the warranty and the address of the warranty provider can be found
in the enclosed user instructions for the given type of equipment.
•The warranty does not include accumulator batteries or batteries of any type, excessive
damage due to overvoltage (including lightning) and damage due to battery acid spillage.
This device has a 3-year warranty period according to our warranty conditions!
Safety instructions, commissioning, battery care, warranty conditions and possible sources of
faults can be found in the enclosed operating instructions!
10. TROUBLESHOOTING - POSSIBLE FAULT SOURCES
Cause Troubleshooting
Pairing cannot be completed The surroundings is very noisy, or the signal between
the Monitor and the Gateway is too weak. Try pairing the
device with antennas closer to each other or in less noisy
environment.
The Monitor does not respond to the
application of a magnet
Check the condition of the inserted batteries, replace if
necessary.
Table 2: Possible sources of faults

15
New website
An easy to orient e-shop
BLOG I ADVICE I TIPS
MANUALS FOR DOWNLOAD
We are online

16
Seller‘s stamp and signature:
[phone]
www.fencee.eu
Servis: [phone]
VNT electronics s.r.o.
Dvorská 605, 563 01 Lanškroun
Czech Republic
[e-mail]
06102020
fencee.cz fenceeczech
print
Electric fencing