dreambaby F854 User manual

IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEE
P FOR F UTURE REFERENCE
If you sell or give away this product, make sure you give this instruction to the new owner.
INSTRUCTIONS
Liberty Security Gate
F854
F867
F919
F920
F1961
F1962
F1963
F1964
Item numbers may also end in BB.
Caution:
With any pressure mounted gate, a construction bar is required across the base. Note, this bar can be a tripping hazard. If you choose
to position a pressure mounted gate at the top of stairs, use extra caution to step over this bar to prevent trips and falls.
Can be used in conjunction with a Dreambaby
®
Watch-the-Step
®
Gate Ramp (F837) to help avoid tripping.
WARNING
WARNING - Incorrect installation can be dangerous.
WARNING - Do not use the safety barrier if any components are damaged or missing.
WARNING - The safety barrier must not be fitted across windows.
WARNING - Never use without wall cups.
Screws MUST always be used to install wall cups.
This safety barrier is for domestic use only.
This safety barrier is suitable for use with children up to 24 months of age.
Not every child is the same. If your child of less than 24 months is able to pass through, climb
over, crawl under or able to open or to dislodge the safety barrier, then the safety barrier can’t
be used to provide the assumed protection.
Never use with a child able to climb or dislodge/open gate.
The surfaces that the gate is to be fixed to must be suitable for the purpose and must be
structurally sound.
If the barrier is to be used at the top of the stairs, it should not be positioned below top level.
If the safety barrier is used at the bottom of the stairs, it should be positioned at the front of
the lowest tread possible.
This gate has a manual close system.
This gate is intended for indoor use and is not to be exposed to outdoor elements.
Install this gate away from heaters and other sources of heat.
This product will not necessarily prevent all accidents. Never leave child unattended.
Conforms to EN1930:2011
1

PARTS LIST
E x 4
H x 4
F x 4
G x 4
J x 4
C
A
G
H
I
D
BEF
The gap in
this gate is
NOT a fault.
The gap will
disappear
when the gate
is correctly
installed .
NOTICE TO CUSTOMERS
IMPORTANT NOTICE
to Customers
The gap in this gate is NOT a fault.
The gap will disappear when the
gate is correctly installed.
Refer to enclosed instructions for
correct installation procedures.
F - Gate Notice
A Gate Panel
B Upper Locking Set
C Release Switch
D Gate Frame
E Tension Knobs
F Bolts with Rubber Pads
G Wall Cups
H Double-sided Adhesive Tape
I Lower Locking Set
J Wood Screws
Wood Screws
Wood use only
WARNING:
This package contains small parts and
sharp points in an unassembled state.
Keep out of reach of children.
Adult assembly required.
2

INSTALLATION
Ensure the surface you are mount the gate is structurally sound such as solid timber, brick or masonry.
For plaster / gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster / gyprock alone is not strong enough and not safe). DO NOT MOUNT TO GLASS.
For use on stairs
1. Measure the width of the opening of where you intend to install the gate .
For wider openings select the appropriate Gate Extension(s), sold separately.
75 - 81cm / 29.5 - 32in 75 - 81cm / 29.5 - 32in
F854 / F919
F1961 / F1962
Xtra-Tall
99 - 105.5cm / 39 - 41.5in 99 - 105.5cm / 39 - 41.5in
F867 / F920 Xtra-Wide
F1963 / F1964 Xtra-Wide, Xtra-Tall
F768
F769
F773
F774
F775
F776
F777
F1992
F1961 + F1965 (9cm/3.5in)
F1961 + 2 x F1965 (9cm/3.5in)
F1963 + F1965 (9cm/3.5in)
F1963 + F1965 (9cm/3.5in) + F1967 (18cm/7in)
F854 + 2 x F901 (9cm/3.5in)
F854 + F901 (9cm/3.5in)
F867 + F901 (9cm/3.5in)
F919 + F968 (9cm/3.5in)
75-90cm
75-99cm
99-114.5cm
99-132.5cm
75-99cm
75-90cm
99-114.5cm
75-90cm
29.5-35.5in
29.5-39in
39-45in
39-52in
29.5-39in
29.5-35.5in
39-45in
29.5-35.5in
Fits openings
KITS
K2
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
&
&
&
&
&
&
&
&
&
Bottom of stairs
Landing
Top of stairs
Floor 5cm
2in
If the safety barrier is used at the top of stairs, it
should not be positioned below the top level.
At the top of landing, position the gate 5cm / 2in
away from the top step.
If the safety barrier is used at the
bottom of the stairs, it should be
positioned at the front of the lowest
tread possible.
Always open
door AWAY
from stairs.
3

A maximum of 2 Gate
Extensions can be used,
1 on each side of gate.
Do NOT install 2 Gate
Extensions on the same side
of gate.
WARNING
2. To use with Gate Extensions.
INSTRUCTIONS :
1. Install Lower Clamp Xonto bottom of gate extension using Z.
2. Insert short end of Extension Pin Kinto gate frame.
3. Slip the gate extension over pin.
4. Screw Upper clamp Yinto place using W.
KYW
XZ
X
Z
Y
W
K
K
X
PARTS
K - Extension Pin
W - Screws
X - Lower Clamp
Y - Upper Clamp
Z - Connector Screw
For Extensions over 36cm / 14in
Insert Extension Pins K into the holes on the outside of the Gate Frame D
Next, slip Extension Frames L over the Pins K .
Finally, slide in the Tension Knobs
E and Bolts with Rubber Pads F .
D Gate Frame
E Tension Knobs
F Bolts with Rubber Pads
9cm / 3.5in
E
F
D
KL
Insert SHORT END of
EXTENSION PIN (K)
into Gate Frame
Insert LONG END of EXTENSION
PIN (K) into Gate Frame
9cm/3.5in
DL
F
K
E
*F901/F968 - 9cm (3.5in)
*F1989 - 2x9cm (3.5in)
F902/F969 - 18cm (7in)
F903/F970 - 27cm (10.5in)
F1951/F1952 - 36cm (14in)
F1953/F1954 - 45cm (17.5in)
F1955/F1956 - 54cm (21in)
F1957/F1958 - 63cm (24.5in)
F1959/F1960 - 100cm (39in)
Gate Extensions (sold separately)
*F1965/F1966 - 9cm (3.5in)
F1967/F1968 - 18cm (7in)
F1969/F1970 - 27cm (10.5in)
F1971/F1972 - 36cm (14in)
F1973/F1974 - 45cm (17.5in)
F1975/F1976 - 54cm (21in)
F1977/F1978 - 63cm (24.5in)
F1979/F1980 - 100cm (39in)
Xtra-Tall
DL
K
K1
K2
K3
9cm / 3.5in
18cm / 7in &
27cm / 10.5in
36cm / 14in —
100cm / 39in
K Extension Pin
L Gate Extension
4

Top view of gate Side view of gate
floor floorfloor
5A
5. Tighten both of the lower Tension Knobs (E) by turning them at the same time.
NOTE: Make sure the bottom of the gate frame remains completely flat on the floor.
Next, tighten both of the upper Tension Knobs (E) by turning them at the same time.
When first installing,
the gate will have this gap.
This is normal and will
disappear when gate is
completely installed.
Tighten
inward Tighten
inward
5B 5C
Tighten
inward
E
D
4. Place the gate in the opening so that the bottom of the Gate Frame is completely flat on the floor,
and it is perpendicular to the opening and the floor.
3. Insert the Bolts with Rubber Pads and Tension Knobs into the Gate Frame.
x 4
E
x 4
F
5

Y
X
Y
X
MAX
6cm
2.5in
Keep this gap about
1mm/0.04in
6. Tighten the Tension Knobs until the two Indicator Lines, located on the Upper Locking Set(B) align horizontally.
When correctly tightened, the distances between Tension Knobs and Rubber Pads should be equal.
Distance
should be
equal
Y=Y
X=X
Indicator
Lines
7. Use a pencil to mark around the ends of the 4 Bolts with Rubber Pads (F).
G x 4
H x 4
8. Loosen the Tension Knobs and remove gate.
Add tape (H) to Wall Cups (G)
Line up Wall cups with marks on wall. Check gate is in alignment. Press Wall Cups (B) firmly into place.
G
F
B
6

Keep this gap about
1mm/0.04in
Distance
should be
equal
Y=Y
X=X
X
Y Y
X
Indicator
Lines
MAX
6cm
2.5in
10. Reinstall gate inserting Bolts with Rubber Pads into Wall Cups (B).
F
x 4
J
G x 4 J x 4
H x 4
9. Screw Wall Cups (G) into place.
Never use without wall cups.
Screws MUST always be used
to install wall cups.
Wood screws (J) included.
For Brick or Masonry use the appropriate fittings,
screws and plugs for your wall (not included)
Ensure the surface you are mount the gate is structurally sound such as solid timber, brick or masonry.
For plaster / gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster / gyprock alone is not strong enough and not safe). DO NOT MOUNT TO GLASS.
Wood use only
Wood Screws
7

1. To open the gate:
MAINTENANCE & CARE
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check Tension Knobs, Rubber Pads and Wall Cups to make sure the gate is securely in place and closes correctly.
Adjust as required.
• Only use Dreambaby
®
spare parts. Any additional and replacement parts should be obtained from Tee-Zed Products.
• To clean, wipe surface with a damp cloth using mild detergent and warm water.
Never clean with abrasive, ammonia, bleach or spirit based type cleaners.
CONTACT DETAILS
OPERATION
2.To close the gate:
This gate has a manual close system. Make sure the Upper and Lower Locking sets are engaged (2A & 2B).
Tee-Zed acknowledges that its customers may be entitled to statutory consumer guarantees and does not seek to exclude or limit them. These guarantees
include that Tee-Zed’s products are of acceptable quality. This Tee-Zed product is for the specific purpose detailed in the instructions and packaging and Tee-Zed
considers use outside of that purpose to be abnormal use. To the maximum extent permitted by law, Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
Dreambaby
®
products by
Tee-Zed Products Pty Ltd
PO Box 2022,
Bondi Junction NSW 1355
Australia
[phone]
[e-mail]
www.dreambaby.com.au
Tee-Zed Products (N.Z.) Ltd
PO Box 64013,
Botany Town Centre Auckland
New Zealand
� [phone]
[e-mail]
www.dreambaby.co.nz
Lift Gate Panel up
to open
1B
Release
Switch
Slide
1A Gate opens in
both directions
1C
C
F854.F867.F919.F1961.F1962.F1963.F1964_ IM_pages1-8_01.07.19_PRESSURE_Mounted_X.03
Tee-Zed Products Ltd
PO Box 29227,
Dunfermline, KY12 2DN
United Kingdom
�[phone]
[e-mail]
www.dreambaby.co.uk
SMART STAYOPEN SYSTEM
To engage the Smart
Stay-Open System
swing gate to its
maximum opening.
Gate will stay open.
Close as required.
CAUTION: Keep gate closed when children are present.
Gate in CLOSED position
Swing to OPEN positions
TOP VIEW OF GATE
Made in Hangzhou, China.
©2019 Tee-Zed Products Pty Ltd
2A 2B
Upper
Locking Set
B
A
A
Lower
Locking Set
I
A
8