Fenton 351.1833 User manual

351.1833 CCTV Security 4 Cam Wireless
NVR kit. User Manual
User Manual
Handleiding
Betriebsanleitung
V2.0

1. Statement
Thanks for purchasing our products, please contact us for any question or requirement.
This manual is meant only for FENTON wireless network video recorder kit.
2. Safety Cautions
1. Please do not put any container with liquid on the device(like vase with water).
2. Please put the device at a ventilated place and prevent clogging the ventilation hole.
3. Please check the power voltage, to avoid any damage to device caused by wrong voltage.
4. The NVR should work under the technical standard temperature and humidity.
5. Please place the device horizontally and keep it away from sharp pounding environment.
6. Moisture and dust on the unit may cause short circuit, for long-term use, please remove the dust on the
unit, connector by brush periodically.
7. Battery replacement by yourself is not suggested, since incorrectly operation may cause burst. Please
contact professional person for battery replacement.
8. Please install the device according to safety norms, you could take the national or local standard as
reference.
3. Package Inspection
Please check the device and all accessories according to packing list. Please contact the distributor timely
in case of any damage or lack of accessory.

1. Product Features & Specification
1.1 Wireless NVR Features
2.4GHz transmission technology 4CH 720P wireless NVR.
Embedded Linux operation system.
Standard H.264 video compression.
Main Chip: Professional industrial processor Hi3520.
4CH 720P real-time recording & synchronous playback.
Auto code matching realizes convenient real P2P application.
More stable wireless signal, Max. 35M transmission distance.
SSID technology guarantees the safety of use.
Motion detection, privacy masking, email alert.
Multiple simultaneous viewing by web browser or smart phone.
Support HDMI/ VGA video output.
Support HDD, USB flash driver storage & backup.
Reserved 3 Ethernet ports for wired IP camera connection.
1 * Standard RJ45 Port, 2*USB 2.0 Port
Network Protocol: UPnP, SMTP, PPPoE, DHCP, FTP, ETC.
1* SATA, Max. 4TB HDD.
Power: DC 12V 2A.
Wireless NVR Technical Parameters
Operating System
Embedded Linux OS
Main Chip
Hi3520
Video Input
4 channel bandwidth 20Mbps
Video Output HDMI
1024*768, 1336*768, 1440*900, 1920*1080
Video Output VGA
1024*768, 1336*768, 1440*900, 1920*1080
Video Playback
4channel synchronous playback 720P / 960H / D1 optional
Recording Mode
Auto / Manual / Motion Detection / Alarm
Playback Mode
Multiple slow / fast playback, real time, routine, event
Backup Mode
Support HDD, USB flash driver, E-cloud storage & backup
HDD Type
1*SATA, Max.4TB
External Interface
4*LAN port (1* adaptable RJ45 10M/100M WAN port
3*reserved LAN port for wired IP camera)
Network Protocol
Upnp(play & plug), SMTP(email service), PPPoE(dial-up),
DHCP(automatically obtain an IP address), etc.
Power Supply
DC 12V/2A
Power Consumption
<= 5W
Working Environment
Temperature -10°--50°, Humidity 10%--90%
Size
257(L) * 210(W) * 45 (H)mm
Weight
1 KG

1.2 Wireless IP Camera Features
2.4GHz wireless transmission technology.
Standard H.264 video compression.
Enhanced wireless module, more stable signal.
Up to 25M transmission distance.
1.0 Megapixels/ 720P wireless IP camera.
Sensor: 1/4” Progressive Scan CMOS Sensor.
Main Chip: Professional industrial processor.
Solution: OV9712+Hi3518E.
Fixed 3.6mm/ 6mm lens optional.
Main stream 1280x720@30fps.
Min. illumination 0.01Lux (0Lux IR Led on).
Smart IR-cut, auto switch day& night vision.
F5* 36pcs IR Leds, 25M effective visual range.
Auto white balance, high sensitivity.
Power: DC12V 1A.
Wireless IP Camera Technical Parameters
Operating System
Embedded Linux OS
Main Chip
Professional industrial processor
Image Sensor
1/4’’ Progressive scan sensor
Solution
OV9712+Hi3518E
Image Resolution
1.0 megapixel, 1280x720P
S/N Ratio
>48dB
Minimum Illumination
Color: 0.1 Lux, B/W: 0.01 Lux
Lens
Fixed 3.6mm
IR Leds
36pcs Leds
Effective Range
Night vision 25M
OSD
Optional (Date Time & Title)
White Balance
Auto
Day & Night
Auto / Color / B&W
3D-DNR
Auto
Mirror / Flip
On / Off
Privacy Masking
4 zones selectable
Frame Specification
Dual Stream: H.264 128x720@30fps or lower
Sub Stream: H.264 640x480@30fps or lower
Anti-thunder Level
Standard IEC6100-4-5
Interface
RJ45/WIFI 802.11b/g/n
Working Environment
Temperature -10°--50°, Humidity 10%--90%
Size
180(L) * 62(W) mm
Weight
500Gr

2. Hardware Operation
2.1 Front Panel
1．PWR：Power indicator light
2．HDD：Hard disk indicator light
2.2 Rear Panel

2.3 Connection Diagram
2.4 Antenna Direction
2.5 Hard Drive Installation
Please note the NVR recorder was pre-installed 1TB HDD inside.

1.Hard drive storage capacity measurement conversion
B
1 B = 8 b
MB
1 MB = 1000 KB
GB
1 GB = 1000 MB
TB
1 TB = 1000 GB
2. How to calculate recording consumption of HDD capacity
--1. One channel recording file size in one hour: A= B / 8 / 1000 *3600
--2. “N” channels recording file size in 24 hours: A= B / 8 / 1000 *3600 *24 *N
--3. “N” channels recording file size in D days: A= B / 8 / 1000 *3600 *24 *D *N
A: Required memory ; B: Code rate ; N: Channels ; D: Recording days
2.6 Packing List
3. System Software Operation
3.1 Turn on/off
1. Make sure the access AC voltage is stable during NVR configuration and use.
2. Connect NVR to monitor by HDMI / VGA video output cable.
3. Apply power to boot up the device, the [power] indicator will be on. When entering the system, it’s a
normal status if the status indicator flashes. The system booting as shown below.
No.
Items
Quantity
1
Wireless NVR
1 pcs
2
Wireless IP camera
4 pcs
3
USB mouse
1 pcs
4
1TB HDD (pre-installed)
1 pcs
5
1M network cable (for IP camera code
1 pcs
6
DC 12V/2A power adapter (for NVR)
1 pcs
7
DC 12V/1A power adapter (for IP
4 pcs
8
FENTON User Manual
1 pcs
9
CD disk
1 pcs
10
Screw bag
4 pcs

3.2 Login
After system is turned on and initialized，it will pop up the login interface automatically as shown below.
Login steps:
1. Left click and enter user name to login. (default users name is “admin” by factory setting)
2. Left click and enter the logging password.(default password is blank by factory setting)
3.Click the “OK” to complete login.
Note: Password can be numbers, operators or */ #, for no longer than 10 characters.
3.3 Logout
Right click mouse to get main menu, go to Exit system (System logout)→ Logout/ Reboot/ System
shutdown.
If users need to logout automatically, steps are below:
Right click mouse to get main menu→ System setup→ General setting→ enable logout automatically→
device logged off without operation in 1 minute→ Re-enter user name & password to login.
3.4 Rebooting
Right click mouse go to main menu, select “ System logout”, click the “rebooting”
4. Setup Wizard
After Logging in, the system will automatically open ” Setup wizard” to help user to complete basic settings.

4.1 Setup wizard
Scan QR-code to download the APP by mobile phone viewing. Check “Enable boot wizard”. (If users do not
click “Enable boot wizard”, all setup wizards steps below will not be prompted at next restarting)
4.2 General setup
Change the time zone/ date / time / language etc, click next to go to HDD setup as below.
4.3 HDD setup
Users can check Hard drive’s model number, capacity, status,etc as below. Also users can format HDD.
And click next to go to record setup.

4.4 Record Setup
Users can choose different record mode. Preset record plan based on channels, weekdays, and schedule,
user can set 4 schedule in the weekday selected for each channel. Or only recording by time / motion /
sensor as shown below.
4.5 Network setup
Users can choose auto DHCP, or edit IP address / gateway / subnet mask / PPPoE etc. click “Done” to
complete all setting as shown below.

5. Video Management
5.1 Refresh
Users can click “Refresh” all wireless IP camera in same subnet.
Steps: Right click mouse to get main menu→ IPC add→ Video manage→ Refresh as below
5.2 Match code
Users can add the IP camera with NVR after matching code.
The IP cameras and NVR have been matched code by factory setting, this device will work normally when

applying power. No need to match code. While if users need to add some new cameras, the cameras must
be matched code with NVR to get video.
Steps: Connect camera with NVR LAN port by network cable→ click NVR main menu Add IPC→ Video
manage→ Match code→ click Yes to mach code.
Note: If device prompt match code unsuccessfully, users need to click “Refresh” to search camera. If
camera can’t be searched, please connect the network cable again to match.
5.3. Delete IP Camera
Users can delete the camera to disconnect video recording.
Steps: Right click to get main menu→ Add IPC→ Video manage→ choose Channel (device name)→ click
Delete channel. Click “Delete all” button to achieve a key operation to remove all cameras.

5.4 Edit channel
Users can modify protocol, IP address, port, user name, password and stream type for each channel.
Steps: Right click to get main menu→ Add IPC→ Video manage→ choose Channel (device name)→ click
Edit channel→ Setup camera configuration as below.
Note: Users can setup stream type (main stream / sub stream) and resolution to check video image upon the
network conditions.
6. Network Setup
6.1 Network setup
1. Right click mouse to get main menu→ System setup→ Network setup, then edit the network as shown
below.

2. Users can choose auto DHCP, or edit IP address / gateway / Subnet mask / PPPoE etc manually. It’s
similar steps as part 4.5.
3. Click OK to save setting.
6.2 DDNS
If the device is without a fixed IP address, users can access it via domain name (dynamic DDNS).
Steps: Right click mouse to get main menu→ System setup→ Network setup→ DDNS→ click Enable and
input URL, user name, password→ click OK to save setting.
1. The DDNS can’t be editable if users do not click “Enable”.
2. Supported network domain type: popdvr, 3322, changeip, no-ip, dyndns.
6.3 FTP
FTP function is used for uploading the file of motion record and sensor record.
Steps: Right click mouse to get main menu→ System setup→ Network setup→ FTP→ FTP function
“Enable”→ enter FTP server, port, users name, password etc→ setup Schedule→ click Test→ click OK to
save setting as below.
Items
Introduction
Remark
IP
Revise local IP address
Edit IP address manually
Subnet
Revise subnet mask
Gateway
Revise gateway IP
MAC
Default MAC address
The device is with the only MAC address
Web port
Web port is used to transmit video &
other control signals.Default code 80
Access device by Webpage/ PC client/ smart
phone are use this same port
DHCP
Click DHCP, device will search local IP
IP address can’t be revised manually if enable DHCP
ESee ID
P2P online remote reviewing
Add device ID to remote view by PC or phone

6.4 E-Mail
Enable E-mail function, the motion record and sensor record file will be notified to users by E-mail.
Steps: Right click mouse to get main menu→ System setup→ Network setup→ E-mail→ Email function
“Enable”→ enter SMTP server, port, users name, password,sender etc→ click Test→ click OK to save
setting as below.

Setup Instruction
Items
Instruction
SMTP server
Input format as smtp. “mail server domain name” .com
User name
User name of mailbox
Password
Email password
Encryption type
Default status is “None”
Sender
Sender’s email address
Sendee
Receiver’s email address
Interval
Interval of emails receiving time
Health mail interval
Interval of emails sending time
1. Users need to enable “Health mail interval” to make sure it’s effective.
2. Users must check their mailbox has been enabled SMTP function.
6.5 PPPoE
PPPoE function is used to be dail-up internet connection.
Steps: Right click mouse to get main menu→ System setup→ Network setup→ PPPoE→ PPPoE function
“Enable”→ setup users name, password→ click OK to save setting as shown below.
6.6 3G
Step: Right click mouse to get main menu→ System setup→ Network setup→ 3G→ Enable 3G module→
setup Dial number, APN, PIN, user name, password→ click OK to save setting as shown below.

7. Video Record
For video record, the recording precedence level is Sensor record> Motion record> Manual record> Time
record.
7.1 Manual record
Users can check or close the video by manual record. Right click mouse to get main menu, go to Manual
record→ Choose the channel No. (click All if needed)→ OK/ Cancel.
7.2 Time Record
The system only record during the schedules upon users’ setting. Right click mouse to get main menu, go
to System setup→ Record setup→ Record plan→ choose Channel No. & Weekday→ choose Schedule→
click Time→ Copy to all (if all channels are same schedule)→ click OK to save setting.

In time record, it’s available to set 4 schedules. While users only need to choose 【00: 00~23:59】if record
in full 24 hour, others schedules are no need to fill.
7.3 Motion record
The system only record in case of detecting people or objects motion. After completing steps 4.6.2, right
click mouse to get main menu, go to System setup→ Record setup→ Video detection→ choose
Channels→ setup Sensitivity “High”→ setup Detection “Motion” → set Alarm/ Buzzer/ Email notice/ FTP
upload→ click OK to save setting.
1. Please copy the same steps to set motion record for each one channel.
2. Please note to set Detection at mode “ video loss” & “video cover” at same way.
3. The default status of sensitivity is high.

7.4 Sensor record
Right click mouse to get main menu, go to System setup→ Record setup→ Sensor setup→ choose
Channel→ Work mode→Alarm duration→set Alarm/ Buzzer/ Email notice/ FTP upload→ click OK to save
setting.
1. Please follow steps 4.6.2 to set sensor record plan, and click the option “Sensor” item.
2. Click record channels “all” or “Copy to all” if all channels sensor setup are same as the first channel
setting.
8. Video Playback
8.1 Rapid playback
Enable rapid playback, users can review the most recent record data easily.
Right click mouse to get main menu, go to Video playback→ Time length (x mins)→ Channel No.→ Check
video.

8.2 Normal playback
Enables normal playback, users can retrieve video data based on the type and recording time.
Right click mouse to get main menu, go to Video playback→ Channel No.→ Record mode→ Search time
(input beginning time and ending time)→ click Search. Recording will come out within 30s. Drag time bar,
click Playback to start.
1. Dragging time bar to control playback progress.
2. 2X, 4X, 8X, 16X and 32X times playback are available.
Dragging bar icon introduction
Button
Function
Playback previous frame
Playback next frame
Play
Pause
Fast forward x2, x4, x8
9. Video Backup
This device support USB flash drive to backup, max. 32GB USB-stick readable.
Connect USB-stick to device, right click mouse to get main menu, go to “Video backup”→ Channel No.→
Record mode→ Search time (input beginning time and ending time) → click Search. Recording will come
out within 30s. Click Backup to copy the video as below. Recording will be stored every one hour.