Fezz Audio SAGITA User manual

USER’S MANUAL

2
SAFETY TIPS______________________________________________
•Never place the Fezz Audio Sagita preamplifier near heat sources, such as radiators,
heaters or direct sunlight. Ensure adequate ventilation and airflow
•We also warn against exposure of the preamplifier to conditions such as very low
temperatures and/or high humidity.
• The preamplifier should be plugged directly into a wall socket. If you must use an
extension cord, please make sure that it has load parameters sufficient to ensure
proper handling of current delivery to the device.
• When cleaning, always disconnect the Sagita from the power source. Use a dry, soft
cloth. Do not use water or cleaning agents.
• If your preamplifier starts to misbehave or to work incorrectly, if it’s temperature
gets too high or you start feeling smoke - immediately disconnect the device from the
mains.
• Due to the risk of exposure to high voltages – please do not open the lid of the
amplifier. ATTENTION: This warning remains in force also in a situation where the
device is already disconnected from the wall outlet.
• Always replace fuses in accordance with the original, intended specification.
• Do not make repairs on your own, or adjustments beyond those as described in this
manual. Execution of any unauthorized repairs or modifications of the device result in
a loss of warranty.

3
TABLE OF CONTENTS_______________________________________
SAFETY TIPS 2
INSTALLATION OF THE DEVICE 4
Unpacking 4
Contents of the package 4
Where to place the preamplifier 4
Description of elements of the preamplifier 5
INTERCONNECTIONS 6
FIRST POWER-UP AND GETTING STARTED 7
OPTIONAL EQUIPMENT 7
Remote control 7
TROUBLE-SHOOTING GUIDE 8
TECHNICAL DATA 8
DECLARATION OF CE CONFORMITY 9
W
YGRZEWAN
IE WZMACNIACZA ___15___
WARUNKI GWARANCJI OGRANICZONEJ ___18___

4
INSTALLATION OF THE DEVICE_______________________________
UNPACKING
Please kindly check if the packaging of the Sagita preamplifier has not been damaged during
transit. If you find any damages, please immediately contact your dealer. Remove the
preamplifier and accessories from the packaging. Make sure that the content is not damaged.
Please do not dispose of the original packaging, so as to facilitate possible shipment of the
device in the future.
CONTENTS OF THE PACKAGE
The package should contains:
•Fezz Audio preamplifier
•power cord
•user’s manual
•optional: remote control,
If any of the above items are missing in your package, contact your dealer immediately.
WHERE TO PLACE YOUR PREAMPLIFIER_______________________
Always provide adequate ventilation for your Sagita preamplifier. Cool operation ensures the
longest possible operating life for any electronic equipment. Do not install the Sagita
preamplifier directly above a heat generating component such as a high powered amplifier.

5
DESCRIPTION OF ELEMENTS OF THE PREAMPLIFIER
1 ) RCA line inputs
2 ) RCA direct input
3 ) RCA line outputs
4 ) IEC power supply cord socket
5 ) Main fuse socket
6 ) Mains switch
8)
7 ) Volume potentiometer
8 ) Output selector
9 ) Power button / Source selector
10 ) Power indicator light

6
CONNECTIONS____________________________________
The figures above shows the front and rear panel views of the Fezz Audio Sagita preamplifier,
together with the description of the inputs and outputs allowing for connection of the other
elements of your audio system.
Follow the instructions below to connect Your sound system correctly.
STEP 1 / CONNECT THE PREAMPLIFIER TO THE POWER AMPLIFIER
Sagita preamplifier has two pairs of power amplifier outputs (3). Please connect the power
amplifier to the one pair of the RCA outputs (3). If you are using two MONO power
amplifiers, please connect one to the L output, second to the R output. Select the source of
output signal by rotating the output selector (8) located on the front panel of the
preamplifier.
The quality of the connecting cable is important. Please pay attention to the output cable
quality as it can have an impact on the performance qualities of the sound.
STEP 2 / CONNECT THE ANALOG SOURCES
Connect the signal sources to the preamplifier inputs (1) Select the source of input signal by
rotating the input selector located on the front panel of the preamplifier (9). In order to
achieve the highest sound quality, use only high-quality RCA cables. Pay attention to the proper
connection and distinction of the right (R) and the left (L) channels.
DIRECT INPUT – You can connect analog signal source (2) and bypass the Sagita`s preamplifier
volume potentiometer. You can control the volume using variable output in your player.
STEP 3 / CONNECT THE POWER SUPPLY CORD
Make sure that the preamplifier is switched off. Connect the power cord to the IEC socket on
the rear panel of the preamplifier.

7
The preamplifier is designed to operate at a rated voltage of 230V / 50Hz. Connecting the
device to a mains network with incorrect parameters can lead to damage that is not covered
by manufacturers warranty.
FIRST POWER-UP AND GETTING STARTED______________________
Make sure that all of your wiring is connected in accordance with the information as provided
above on page 6 of this manual.
Set the volume control to minimum. Turn on the mains power at the back of the Sagita
preamplifier. (6) After this time the light will turn red. Push power / selector source button to
turn-ON the preamplifier. Select output 1 or 2. Make sure the sound source is turned on, select
source number, then gradually increase the volume level by turning the potentiometer.
OPTIONAL EQUIPMENT_________________________________
REMOTE CONTROL
The IR remote control enables adjustment of the volume level, selecting sources and power
ON/OFF the preamplifier.

8
TROUBLE-SHOOTING GUIDE_________________________________
If your amplifier does not work as it is supposed to, it is fairly easy to diagnose and remedy
some of the common malfunctions, by following procedures as outlined in this following.
THE PROBLEM
PROBABLE REASON
THE SOLUTION
After turning the power switch to the ON
position, the amplifier does not switch on.
A blown fuse
Please exchange to faulty fuse to a new one
(0,2 T), within the fuse holder as depicted
with index 5 on page 5 of this user’s
manual.
An improper connection of the mains cable
Please check if the plugs of the mains cable
are properly inserted into the electrical
mains socket and to the socket as depicted
with index 5 on page 5 of this user’s
manual.
If You have verified the aforementioned situations, and your problem still persists, please
contact Your local Fezz Audio dealer.
TECHNICAL DATA__________________________________________
Type: Stereo preamplifier
Model: Sagita
Inputs : 8xRCA
Outputs: 2x RCA
Power consumption: 12W
AC fuse: 0,2A
Net Weight: 6kg
Dimensions (width x depth x height): 420x410x175mm
Colour schemes: black, white, burgundy, red
Optional equipment as a remote contol,

9
Declaration of Conformity
Manufacturer: Toroidy.pl Transformatory L. Lachowski Sp.k. (owner of Fezz Audio brand)
Address: ul. Mazowiecka 20
16-001 Księżyno
POLAND
I declare that the product:
Brand: Fezz Audio
Model: Sagita Pre-amplifier
complies with the following European Union Council Directives and Standards relating to
electromagnetic compatibility (EMC Directive 2014/30/EU) and the low voltage Directive
(2014/35/EU).
This declaration of conformity is the result of an examination carried out in accordance with
European Standards for EN 60065:2002+A2:2010+A12:2011+A11:2008 for low voltage, as
laid down in article 10 of the EMC Directive.
Księżyno 4.01.2021 Lech Lachowski