Vivo STAND-V002P User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002p
SKU: STAND-V002P
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Base
B(x1)
Arm
C(x1)
Pole
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole Cover
E(x1)
Cable Clip
G (x1)
3mm Allen
Wrench
H (x1)
5mm Allen
Wrench
I (x1)
6mm Allen
Wrench
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
F(x1)
Base Cover

3
ASSEMBLY STEPS
STEP 1
STEP 2
TOOLS NEEDED
Phillips
Screwdriver
Slide the cable management clip (E) and base cover (F) onto the bottom of the pole (C). Loosen the
grub screws in the base (A) using the 3mm Allen wrench (G) and screw the pole into the base. Tighten
the grub screws using the 3mm Allen wrench (G).
Attach the pole cover (D) to the pole (C).
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4
STEP 3
If needed, adjust the support collar height using the 3mm Allen wrench (G).
STEP 4
Slide the arm (B) onto the top of the pole and tighten using the 5mm Allen wrench (H).

5
STEP 5
Insert two bolts (M-A or M-B) and washers (M-C) into the top mounting holes of the
monitors, making sure to leave 3mm of thread exposed. Align bolts (M-A, M-B) in VESA
plates. Secure using two more bolts (M-A or M-B) and washers (M-C) in the bottom
two holes of each monitor. Tighten all bolts using a Phillips screwdriver.

6
STEP 6
Tighten or loosen the tilt joints using the 6mm Allen wrench (I).
STEP 7
Store the Allen wrenches (H, I) in the cable management clip (E) for future adjustments.

7
STEP 8
Do not move monitors past the center point of gravity. This could result in tipping.
STEP 9
If monitor heights are not aligned, turn the screw behind each VESA plate using the 5mm Allen
wrench (H). Clockwise will raise the monitor and counter-clockwise will lower the monitor.

LAST UPDATED: 11/20/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303