Wali MF002XLS User manual

MF002XLS
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Dual Monitor Desk Mount
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
Weighted Base
B (x1)
J1
A1
I
Install the Lower Pole a to the weighted Base b using 3pcs M5x14 Bolts e ,
and tighten with Allen key 3mm o .
2
A1 B
B
I
J1
1
A2
A2
A1
A1
A1
I
I
Option A : 31.5'' Pole Installation
Loosen the screw on the Lower Pole a1 with Allen key 3mm o . Connect
Lower Pole a1 to Upper Pole a2 and tighten the screw with Allen key
3mm o to fix the two poles.
A1
A1
Pre-Assembly
I
A2
I
I
3
Put the Wire Clips k and Monitor Arms d through the Upper Pole a , adjust the preferred
height and tighten using Allen Key 5mm o .
C
C
KA2
I
A2
K
K (x2)
Wire Clip
Nut
E (x2)
M5x14 Bolt
J1 (x3)
Allen Key
I (x1)
M4x30 Bolt
G (x8)
M4x12 Bolt
F (x8) H (x8)
M4~M6 Spacer
VESA Plate
D (x2)
Lower Pole
A1 (x1)
Upper Pole
A2 (x1)
Monitor Arm
C (x2)

7Manually swivel, tilt, and rotate the monitor for the best viewing angle. 6Guide the cable through the Wire Clips and store the Allen Keys o in the Wire Clips k .
Adjust the tilt angle using Allen Key 5mm n .
KK
I
I
45°
45°
45°
45°
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)
Step 4.1
Select Monitor Screws
Step 4.3a
Flat Back Monitor
Step 4.3b
Curved or Recessed Back Monitor
D
D
G
H
F
M4x12 M4x30
4
Only one screw size fits your Monitor
Step 4.2
Select Spacers( if needed )
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4x12 orM4x30)
to use.
5Put the assembled TV/Monitor onto the Monitor Arms d and tighten the VESA Plate e with
Nut h for stability.
h
I
I
K
D
C
E
D
E
C
Notice: Please make sure the security nut is installed before you rotate the monitor.
E
E