fidek FDD-3060II User manual

V:1.0
USER’ S MANUAL

Digital Matrix Processor
INDEX
FUNCTIONS ------------------------------------------------------------------------------ 1
FRONT PANEL ---------------------------------------------------------------------------- 1
REAR PANEL ------------------------------------------------------------------------------ 2
OPERATION GUIDANCE ---------------------------------------------------------------- 2
PC SOFTWARE ONLINE SPECIFICATION ------------------- ----------------------- 5
PC SOFTWARE INTERFACE SPECIFICATIONS ----------------------------------- 6
SPECIFICATIONS ------------------------------------------------------------------------ 11
ACCESSORIES --------------------------------------------------------------------------- 11
REAR PANEL CONTROL PORT CONNECTION ------------------------------------ 12
EXTEND REMOTE CONTROL PROTOCOL CONNECTION----------------------- 13
SAFETY INSTRUCTIONS --------------------------------------------------------------- 16

FRONT PANEL
FUNCTIONS
Input Level Indicators
5-segment high precision LED show the situation of current input channel's level.
Input Edit Keys
Press to enter into relevant channel, parameters will show on the edit key and LCD.
Input Mute Keys
Mute channel by pressing and exit by pressing again.
Parameter edit keys
Choose all the system menu/input parameter/output parameter, exit by pressing ”exit” key.
LCD
Show all the related operation parameter and status of current operation.
Parameter Edit Knob
Edit the whole menu and parameter setting confirm by press.
2
1
3
4
1
Digital Matrix Processor
● 96kHz sampling rate, 32-SHARC DSP processor, 24-bit AD/DA convertor.
● Input processing includes Gain, Mute, Link, High-cut, Low -cut, Noise gate, 8PEQ, Phase, Delay.
● Output processing includes Crossover, 9PEQ, Gain, Mute, Compressor/Limiter, Phase, Delay, Link.
● Every input and output can do matrix assign freely.
● Adjustable PEQ frequency, Gain and Bandwidth, the gain step is 0.1dB, we can choose style: Peak,
H-shelf, L-shelf, Low- cut, High- cut.
● The style of all High-cut, Low-cut filter and Distributor Unit: Butterworth, Linkwitz- Riley, Bessel,
Slope is-6dB/oct ~-48dB/oct.
● Adjustable compressor/limiter threshold, ratio, attached time and release time, Adjustable threshold
attached time, release time, keep time of all noise gate.
● The parameters of input and output adjusting are linkable, revisable input and output channels.
● All delay module's delay time can reach over 682ms the step is: 0.021ms.
● Parameter setting of each channel can copy freely, build-in signal generator.
● Input and Output on the front panel are equipped with 5-segment high precision level indicators, key
indicators, security protection function.
● 30 user preset, 1factory preset, device parameter and single preset file can save in computer; it also
can download from computer and save in the device. The device itself can store multiple preset
parameters and recall freely. PC operation software for one-click online made the operation more
convenient.
● USB and RS232 controlling ports, Online remote control and 255 units linkable through RS485.
5
6
810
9
7
6
45
1
2
3

Output Level Indicators
4-segment high precision LED and1 compressor signal LED shows the status of output level and
compressor on current channel.
Output Mute Keys
Mute channel by pressing and exit by pressing again.
Output Edit Keys
Press to enter into relevant channel edit status parameter will show on the edit, Key and LCD.
USB
Used to connect with PC and center-control equipment, remote control.
7
8
9
10
REAR PANEL
Power Socket
The voltage is 95V-240V.
Power on/off Switch
RS232/485 interface
Center-control by RS232, cascade control by RS485.
Output interface
Male XLR balanced output 1-8.
Signal input interface
Female XLR balanced input A-D.
4
2
1
3
5
2
Digital Matrix Processor
OPERATION GUIDANCE
Below status after power on:
Power on, show brand, model and version.
After self-check, show brand, model and current user preset.
ID Number Select
ID: 1
Press UTIL key, enter below setting status
Press UTIL key one time, enter ID number setting: the ID number of the units,
should be different when cas cade connection, the setting scale is1-254. (If
cas cade connection units are over 16 or long distance, a loaded 120 ohms
resistance should be parallel connected by RS 485.
4X8 DSP
Processor 1.01
4X8 DSP
F00 Default Preset
Unit unlock
Password 1234
Press DOWN key one time, enter password setting: users can choose all the
words or numbers to set the password they want, the initial password is
“1234”.
1 2 345

3
Digital Matrix Processor
In Source Select
ANALOG INPUT
Copy CH select
InA InB
LCD DISPLAY TIME
10 Second
Load preset
F00 Default Preset
Store preset
U01 Default Preset
Press DOWN key two times, enter password memory setting way. OFF
mains that password does not memory. It can operate the panel follow-up
afterunlocking the passesword at first time. ON mains that password memory.
It always needs to unlock the password when open the unit every time.
Press DOWN key three times, enter signal source selection: pink noise, white
noise and sine wave 20Hz-20kHz.
Press DOWN key four times, enter copy channel selection: input or output
channel can copy freely.
Press DOWN key five times, enter delay unit setting: ms, m, ft can be chosen.
Press RECALL/SAVE key, enter below setting status
Press RECALL key, enter preset transfer. Users can transfer the saved
Settings U01-U30 and the initial setting F00.
Press SAVE key, enter preset save. Users can save the adjust status in
U01-U30. Attention that the F00 factory preset can’t save.
Press INPUT EDIT enter the settings as follows
Default preferred option is gain the scale is -60dB-+12dB.
Press DOWN key one time enter PEQ parameter setting PEQ current filter
number Is 8 ,the scale of “F” is 20Hz-20kHz, “Q” is 0.4-128, "G" is -12dB
- +12dB, the style of filter are Peak, Low-shelf, High-shelf, Low-cut, High-cut,
Allpass1, Allpass2, Bypass(ON/OFF).
LOCK Select
OFF
PEQ:1 INA
G: 0.0 FREQ: 50.7 BY
Q: 3.00 TYPE: PEAK □
Press DOWN key six times, enter linking adjustment selection: If the
current channel is INA, you can choose INB, INC, IND channel to adjust
parameter simultaneously, together.
Press DOWN key three times, enter delay parameter setting: the scale is
0-680mS, 0-234m, 0-769ft.
PHASE INA
0: □ 180: □
Press DOWN key four times, enter phasic adjust setting, adjustment scale is
(0/180).
Press DOWN key two times enter low-high pass parameter setting, the scale
of the “HP” is 20Hz -20kHz, “LP” is 20Hz -20kHz, 3 different slanting rate for
low/ high pass filter Butterworth, Bessel, Linkwitz-Riley, Slanting rate is
-6dB--48dB.
HI & LOW - PASS INA
HP: 19.6 BYPASS
LP: 20K15 BYPASS
DELAY INA
0.000ms
0.000m 0.000ft
√
IN-LINK INA
A: □ B: □ C: □ D: □
√
GAIN INA
-60.0dB
GATE INA
TH:-90 Hold: 100ms
AT: 1ms REL: 100ms
Press DOWN key five times, enter GATE adjust interface, “TH” scale is -60dB
-0dB, “Hold” keeping time is 1-999ms, “AT” attached time is 1-999ms, “REL”
release time is 10ms-300ms.

4
Digital Matrix Processor
:
GAIN OUT1
+0.0dB
Press DOWN key one time, enter PEQ PARAMETER SETTING: ”PEQ” current
number is 9, the scale of “F” is 20Hz-20kHz, “Q” is 0.4-128 “G” is -12dB
- +12dB, the style of filter are Peak, Low-shelf, High-shelf, High-cut, Low-cut,
Allpass1, Allpass2, Bypass(ON/OFF).
DELAY OUT1
0.000ms
0.000m 0.000ft
Press DOWN key four times,enter delay parameter setting: the scale is 0-680
mS, 0-234m, 0-769ft .
Press DOWN key two times, enter low-high pass parameter setting: the scale
of “HP” is
20Hz-20kHz, “LP” is 20Hz- 20kHz, 3 different slanting rate for low/high pass
filter: Butterworth, Bessel, Linkwitz-Riley, Slanting rate is -6dB--48dB.
Press DOWN key three times, enter matrix setting, all the output channel can
choose one
or several input signal freely.
Press DOWN key five times, enter phase parameter setting: the scale is
°0/180°.
Default preferred option is gain, the scale is- 60dB--12dB.
Press OUTPUT EDIT enter the settings as follow
Press DOWN key six times, enter compressor setting: the scale of threshold is -60dB
~+20dB, startup time is 1-999ms,attached time is 10-3000ms, ratio is 1:1, 1:10-LIMIT..
Press DOWN key seven times, enter linking adjustment: select the
corresponding channel can adjust the parameters.
COMPRESSOR OUT1
TH:+20.0 RAT:1.0
AT: 50ms REL: 500ms
MATRIX OUT1
A: □ B: □ C: □ D: □
√
PEQ: 1 OUT1
G:0.0 FREQ:40.2 BY
Q:3.00 YPTE: PEAK □
HI&LOW-PASS OUT1
HP: 19.6 BYPASS
LP: 20K15 BYPASS
PHASE OUT1
0: □ 180: □
√
OUTLINK OUT1
1: □ 2: □ 3: □ 4: □
5: □ 6: □ 7: □ 8: □
√

USB connection steps
USB connection
USB cord
1, Click the PC software on the CD, press next step to continue according to the instruction until
Finish setup, then exit.
Notice: User manual, PC software are on the attached CD, due to the software upgrades time by time,
Please do control your DSP processor ONLY by this CD!
DSP Processor
PC or laptop
PC SOFTWARE ONLINE SPECIFICATION
Digital Matrix Processor
5
2, Connect the processor to the computer by USB, after turning on the device, the computer will
searching new hardware automatically, during setup new hardware there will show the.
Warnings: hardware setup success and can be used.

3, Open PC controlling software, PC software will find USB and connect device, after that the on-Line
key change into green at the top right corner and show “Online” , you can operate the Processor by
controlling software, Click “Online” button before exit.
Digital Matrix Processor
6
THE FIRST: VOLUME CONTROL INTERFACE
PC SOFTWARE INTERFACE SPECIFICATIONS
2
1
3
4

Digital Matrix Processor
7
1, Menu
File Open and save preset parameter, the whole date upload to the computer
and download to the device.
Link
Copy
Lock
Setting ID
Test Tone
Channel Name
Language Chinese and English menu is switchable.
Help RS232 control protocol codes for reference.
The whole channel name are revisable.
Input and output channels can be set freely to adjust all of the parameters.
Parameter copy freely between the input and Output channels.
Setting password of the panel to ensure the safety of the device.
To cascade control more than 255 device by setting different ID.
Buid-in signal generator, outputting pink noise, white noise and sine wave.
2, Spectrum Area:
You can choose PEQ and phase freely which show the input andoutput channels.
3, The Volume Control Area:
Gain, Phase, Mute control for all input & output channels.
4, Preset Operation Area:
Save or convert preset parameter and show current preset parameter status.
1
2
THE SECOND: NOISE GATE INTERFACE
1,display the current noise gate status curve and input channels level indicators.
2, all input channels noise gate parameters can be set. Noise gate threshold(-60~0dB), attach
time(1~999ms), keep time(1~999ms), release time(10~3000ms) can be adjustable continuously
for input.

Digital Matrix Processor
8
THE FOURTH: DELAY INTERFACE
1, Show the delay parameter status of all channels.
2, Can adjust delay parameter of all channels, the scale is 0-680ms, there are millisecond, meter and
feet units for converting.
1
2
THE THIRD: COMPRESSOR INTERFACE
1
2
1, Show compression status, level indicators and impression status of all channels.
2, Set the whole compression parameters for output channel, the compression range is -60dB–
+20dB, rate is 1:1, 1:10, LIMIT, start time is: 0-200ms, recovery time is 0-999ms.

Digital Matrix Processor
9
THE SIXTH: INPUT INTERFACE
1, Select “Mag" interface, you can adjust the PEQ, High-cut, Low-Cut of the input channel, select
"PHASE" interface, you can adjust the current phase channel, also you can choose the non-current
PEQ and phase curve to show in sync.
1
2
4
356
THE FIFTH: MATRIX INTERFACE
1
2
1, Show connections of the device, users can enter and edit relevant channel by clicking the square ,
every channel name is revisable.
2, All output channels can choose any input channels.

Digital Matrix Processor
10
THE SEVENTH: OUTPUT INTERFACE
1, Select “Mag" interface, you can adjust the PEQ, High-cut, Low-Cut of the output channel, select
"PHASE" interface, you can adjust the current phase channel, also you can choose the non-current
PEQ and phase curve to show in sync.
2, Adjustable Gain, Mute, Q , Frequency, Type of all PEQ, Bypass key is optional, we can choose PEQ
style: Balance, High-shelf, Low-shelf, High-cut, Low-cut, Phase 180° , Phase 360°.
3, The Gain, Q, Frequency of PEQ can be adjusted by putter, and can be controlled by pressing the
UP, DOWN, LEFT, RIGHT key on the keyboard.
4, Low-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate: Butterworth, Bessel,
Linkwitz-Riley, the scale is:-6dB-- -48dB
5, High-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate : Butterworth, Bessel,
Linkwitz-Riley, the scale is:-6dB-- -48dB.
6, The Gain, Mute, Phase of the output channel can control separately, as same as the level display
light.
1
2
4
356
2, Adjustable Gain, Mute, Q , Frequency, Type of all PEQ, Bypass key is optional, we can choose
PEQ style: Balance, High-shelf, Low-shelf, High-cut, Low-cut, Phase 180° , Phase 360°.
3, The Gain, Q, Frequency of PEQ can be adjusted by putter, and can be controlled by pressing the
UP, DOWN, LEFT, RIGHT key on the keyboard.
4, Low-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate: Butterworth, Bessel,
Linkwitz-Riley, the scale is: -6dB-- -48dB.
5, High-cut frequency 20HZ-20KHZ is adjustable, you can choose slope rate : Butterworth, Bessel,
Linkwitz-Riley, the scale is: -6dB-- -48dB.
6, The Gain, Mute, Phase of the input channel can control separately, as same as the level display
Light.

Digital Matrix Processor
11
System Specification
Input Section
Output Section
Digital Processing
Display
Power Supply
Dimension
Weight
Frequency Response 20Hz~20kHz, -0.3dBu
S/N Ratio
>115 dBu
Distortion(THD)<0. 005at1kHz(0dBu)
Cross-talk
2.3kg
48.2x20.5x4.4CM
96kHz Sampling Rates
24-bit sigma - delta converters
Impedance
(LxWxH)
Type
Impedance
Max. Input Level
Type
<100dB below full scale
Balanced XLR
+18dBu
1M/Ω
Balanced XLR
+18dBu
<500
Dot matrix screen display For Parameters Setting And Function Select
Stereo; 500kΩ/MONO
Ω
1, CD (Include PC software and user's manual).
2, One USB cord.
3, One electrical cord.
SPECIFICATION
ACCESSORIES
Max. Output Level (bypass)
AC~95V-240V FUSE 250VAC/2A FAST

Digital Matrix Processor
12
REAR PANEL CONTROL PORT CONNECTION
1, RS232 connection port: Central control and connect to PC through RS232 port.
RS232/USB
CONVERTER
PC or laptop
The 2PIN is: TXD, 3PIN
is:RXD, 5PIN is: GND
(1), Connect several devices by cascading 7PIN and 8PIN
of the RS232 port, connect the computer through
(2), RS485 converted RS232 switch, Cascade controllable
several devices after setting the different ID.
2, RS485 cascade contro port: Parallel connect several devices by RS485, you can choose different
ID to cascade control separately.
PC or laptop
The 7PIN is: RS485 D+ , 8PIN is: RS485 D- of the
RS232 port.
ID:1
ID:2
ID:3

Digital Matrix Processor
13
1, Control package Format
2, Command Detail
(1) Gain Control(0x41)
Example (increase input channel 1 gain): 7B7D01410000007D7B
(2) Mute Control(0x42)
Example (input channel 1 mute): 7B7D01420000017D7B
(3)Load Preset Control(0x43)
Example (recall user preset U00):7B7D01430100007D7B
EXTEND REMOTE CONTROL PROTOCOL
01 2 345678
DLE STX Device
Assress
CMD Data1 Data2 Date3
Packet 0x7B 0x7D 1～254 0x41～0x4A 0x? ? 0x7D0x? ? 0x?? 0x7B
STX DLE
01 2 345678
DLE STX Device
Assress
CMD
Packet 0x7B 0x7D 1～254 0x7D 0x7B
STX DLE
0x41 In:0 Out:10～3+:0,-:1
Channel +/-
In/Out
01 2 345678
DLE STX Device
Assress
CMD
Packet 0x7B 0x7D 1～254 0x7D 0x7B
STX DLE
0x42 In:0 Out:10～3No:0 Yes:1
Channel No/Yes
In/Out
Packet
01 2 345678
DLE STX Device
Assress
CMD
0x7B 0x7D 1～254 0x7D 0x7B
STX DLE
0x43 F:0 U:10～31 0
Preset
0x30
Factory/User

Digital Matrix Processor
14
Example (read input channel 1 gain parameter):7B7D01480000007D7B
MCU Return:0x00～0x90=-60dB～+12dB,0.5dB/Step
(7)Get Now Mute(0x49)
Example (read input channel 1 mute parameter):7B7D01490000007D7B
MCU Return:0x00 or 0x01=Un-Mute or Mute
(6)Get Now Gain(0x48)
(4)Input Volume Control(0x44)
Example(InA volume +0.0dB):7B7D01440001187D7B
(5)Output Volume Control(0x45)
Example（Out2 volume -3.0dB):7B7D01450100FA7D7B
Packet
01 2 345678
DLE STX Device
Assress
CMD
0x7B 0x7D 1～254 0x7D 0x7B
STX DLE
0x49 In:0 Out:10～30
Channel
0x30
In/Out
Packet
01 2 345678
DLE STX Device
Assress
CMD
0x7B 0x7D 1～254 0x7D 0x7B
STX DLE
0x48 In:0 Out:10～30
Channel
0x30
In/Out
Packet
01 2 34
DLE STX Device
Assress
CMD
0x7B 0x7D 1～254 0x44 0x?? 00～07
HI-VOL
Channel
5678
0x7D 0x7B
STX DLE
0x??
LO-VOL
Packet
01 2 34
DLE STX Device
Assress
CMD
0x7B 0x7D 1～254 0x45 0x?? 0x?? 00～07
HI-VOL
Channel
5678
0x7D 0x7B
STX DLE
LO-VOL

Digital Matrix Processor
15
(8) Get Now Preset(0x4A)
Example (read preset parameter):7B7D014A0000007D7B
MCU Return:0x00～0x32=0:F00,1～32:U00～U31
Packet
01 2 345678
DLE STX Device
Assress
CMD
0x7B 0x7D 1～254 0x7D 0x7B
STX DLE
0x4A 0 0
0x30 0x30 0x30
0
Communication
parameter
Bits per second
Data bits
Parity
115200
8
None
Stop bits
Step
ID
1
>=20ms
1

Digital Matrix Processor
16
SAFETY INSTRUCTION

Digital Matrix Processor
17