Fieldmann FDUV 70105-0 User manual

FDUV 70105-0

2
FDUV 70105-0
English .................................................................................................................................................................................5–20
Čeština............................................................................................................................................................................. 21–38
Slovenčina .....................................................................................................................................................................39–56
Magyarul ........................................................................................................................................................................57–72
Polski .................................................................................................................................................................................73–89

CORDLESS DRILL USER’S MANUAL
3

4
FDUV 70105-0
43
21
AB
C

EN
CORDLESS DRILL USER’S MANUAL
5
Table of Contents
Cordless Drill
USER'S MANUAL
Thank you for purchasing this Cordless Drill. Before you start using it, please carefully
read this user's manual and save it for possible future use.
CONTENTS
1. GENERAL SAFETY INSTRUCTIONS..........................................................................................................................6
2. SYMBOLS........................................................................................................................................................................... 7
3. PRODUCT DESCRIPTION AND SPECIFICATIONS ............................................................................................8
4. OPERATION......................................................................................................................................................................8
5. APPLICATIONS..............................................................................................................................................................11
6. OPERATING INSTRUCTIONS....................................................................................................................................12
7. MAINTENANCE AND STORAGE............................................................................................................................15
8. TECHNICAL DATA........................................................................................................................................................17
9. TROUBLESHOOTING...................................................................................................................................................18
10. DISPOSAL ........................................................................................................................................................................19
11. DECLARATION OF CONFORMITY .......................................................................................................................20

EN 6
FDUV 70105-0
General safety instructions
1. GENERAL SAFETY INSTRUCTIONS
WARNING!
Carefully read the instruction manual before use.
Important safety warnings
Unpack the product carefully and be sure not to throw away any part of the package before having found all
components of the product.
Keep the product in a dry place out of reach of children.
Read all cautions and instructions. The failure to adhere to warning cautions and instructions may result in
an accident, fire and/or a serious injury.
Packaging
The product is placed in a package preventing damage during transport. This package is a raw material therefore
it can be handed-over for recycling.
Instructions for use
Before beginning to work with the machine, read the following safety rules and instructions for use. Familiarize
with operating elements and the proper use of the device. Keep the manual in a safe place for future reference.
We recommend keeping the original package including the inner packaging materials, cash voucher and
guarantee card for a period of warranty at minimum.
For a case of transportation, pack the machine into the original box from the manufacturer, thus ensuring
a maximum protection of the product during a possible transport (e.g. moving or sending into a service station).
Note:
If you hand the machine over to next persons, hand it over together with the manual. Adherence to the attached
instructions for use is a precondition for the proper use of the machine. The operation manual includes also
instructions for operation, maintenance and repairs.
The manufacturer does not take any responsibility for accidents or damages resulting
from the failure to adhere to this manual.

EN
CORDLESS DRILL USER’S MANUAL
7
Symbols
2. SYMBOLS
The product complies with the applicable
standards and regulations.
Read the Instruction Manual attentively
prior to use.
Use eyes protective equipment
Use ears protective equipment

EN 8
FDUV 70105-0
Product description and specifications | Operation
3. PRODUCT DESCRIPTION AND
SPECIFICATIONS
1. Trigger
2. LED
3. Keyless chuck
4. Torque selector collar
5. Application selector collar (01A-18Li only)
6. Speed selector
7. Control switch
8. Handle
9. Battery (not included)
4. OPERATION
WARNING!
Always remove battery pack before changing or removing accessories. Only use
accessories specificallyrecomended for this tool. Others may be hazardous. To reduce
the risk of injury, always wear safety goggles or glasses with side shields.
Installing Bits
Always remove the battery before inserting or removing bits. Select the proper style and size bit for the job. This
tool is equipped with a spindle lock. The chuck can be tightened with one hand, creating higher grip strengths on
the bit.
1. To open the chuck jaws, turn the sleeve in the counterclockwise direction. When using drill bits, allow the
bit to strike the bottom of the chuck. Center the bit in the chuck jaws and lift it about 1/16” off of the bottom.
When using screwdriver bits, insert the bit far enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the clockwise direction. The bit is secure when the chuck makes
a ratcheting sound and the sleeve can not be rotated any further.
3. To remove the bit, turn the sleeve in the counterclockwise direction.
Note:
A ratcheting sound may be heard when the chuck is opened or closed. This noise is part of the locking feature,
and does not indicate a problem with the chuck’s operation.
Selecting Hammer, Drill or Drive Action
1. To use the hammer-drilling mode, rotate the application selector collar until the hammer symbol
appears in line with the arrow. Apply pressure to the bit to engage the hammering mechanism. (Fig. 1)
Note:
The number selected on the torque selector collar has no effect on operation of the drill in hammer mode.

EN
CORDLESS DRILL USER’S MANUAL
9
Operation
Note:
When using carbide bits, do not use water to settle dust. Do not attempt to drill through steel reinforcing rods. This
will damage the carbide bits.
2. To use the drilling only mode, rotate the application selector collar until the drill symbol appears
in line with the arrow. (Fig. 2)
Note:
The number selected on the torque selector collar has no effect on operation of the drill in drilling mode.
3. To use the driving screws mode rotate the application selector collar until the drive symbol
appears in line with the arrow. Then rotate the torque selector collar until the desired clutch setting appears
in line with the arrow. The adjustable clutch, when properly adjusted, will slip at a preset torque to prevent
driving the screw too deep into different materials and to prevent damage to the screw or tool. The torque
spetifications shown here are approximate values obtained with a fully charged battery pack. (Fig. 3)
Clutch Setting Applications
1–3 Small screws in softwood.
4–6
7–9 Medium screws in softwood or small screws in hardwood.
10–13
14–17 Large screws in softwoods. Medium screws in hardwood or large screws in
hardwood with pilot hole.
18
Note:
Because the settings shown in the table are only a guide, use a piece of scrap material to test the different clutch
settings before driving screws into the workpiece.
Selecting Speed
The speed selector is on top of the motor housing. Allow the tool to come to a complete stop before changing
speeds. See “Applications” for recom - mended speeds under various conditions.
1. For Low speed, push the speed selector to display “1”.
2. For High speed, push the speed selector to display “2”.
Using the Control Switch
The control switch may be set to three positions: forward, reverse and lock. Due to a lockout mechanism, the
control switch can only be adjusted when the ON/OFF switch is not pressed. Always allow the motor to come to
a complete stop before using the control switch.
For forward (clockwise) rotation, push in the control switch from the right side of the tool. Check the
direction of rotation before use. (Fig. 4, A - Forward, B - Reverse, C - Lock Push to CENTER)

EN 10
FDUV 70105-0
Operation
For reverse (counterclockwise) rotation, push in the control switch from the left side of the tool. Check the
direction of rotation before use.
To lock the trigger, push the control switch to the center position. The trigger will not work while the control
switch is in the center locked position. Always lock the trigger or remove the battery pack before performing
maintenance, changing accessories, storing the tool and any time the tool is not in use.
WARNING!
To reduce the risk of injury, always hold or brace securely.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handles firmly and pull the trigger.
Note:
An LED is turned on when the trigger is pulled.
2. To vary the speed, increase or decrease the pressure on the trigger. The further the trigger is pulled, the
greater the speed.
3. To stop the tool, release the trigger. Make sure the bit comes to a complete stop before laying the tool down.
Drilling
Place the bit on the work surface and apply firm pressure before starting. Too much pressure will slow the bit and
reduce drilling efficiency. Too little pressure will cause the bit to slide over the work area and dull the point of the
bit. If the tool begins to stall, reduce pressure slightly to allow the bit to regain speed. If the bit binds, reverse the
motor to free the bit from the workpiece.