Fiery KM-C2030 User manual

QUICK START GUIDE
Part Number: 45040356
22 January 2004
2004  Electronics for Imaging, Inc.
This Quick Start Guide provides system requirements and an overview of how to set up
your Fiery X3e 31C-M Color Server
™
so you can begin printing. The guide describes
the initial tasks you must perform and points you to sections in the user
documentation where the procedures are described in detail. A full set of user
documentation is provided on the User Documentation CD. A brief description of
the user manuals and how to print them follows.
N
OTE
:
The term “Fiery X3e” is used in this document to refer to the Fiery X3e 31C-M
Color Server.
This icon identifies information that applies only to the Fiery X3e copier.
This icon identifies information that applies only to the Fiery X3e printer.
Media pack
Your Fiery X3e media pack should contain the following:
•User Software CD
•User Documentation CD
•Printed Quick Start Guide
•Printed Release Notes
•Kodak Gray Scale

2 Quick Start Guide
About the documentation
Along with the printed Release Notes included in the media pack, documentation
is provided in electronic form on the User Documentation CD. The documents are
provided as Acrobat PDF (Portable Document Format) files, which are linked and
cross-referenced. A description of the documentation follows:
• The Quick Start Guide summarizes the steps for configuring the Fiery X3e and
setting up printing. It also describes how to access the Acrobat PDF files on the User
Documentation CD.
• The User Software Installation Guide describes how to install software from the
User Software CD to enable users to print to the Fiery X3e, as well as how to set up
printing connections to the Fiery X3e.
• The Configuration Guide explains basic configuration and administration of the
Fiery X3e for the supported platforms and network environments. It also includes
guidelines for setting up UNIX, Windows NT 4.0/2000/Server 2003, and Novell
NetWare servers to provide printing services to users.
• The Printing Guide describes the printing features of the Fiery X3e for users who
send jobs from their computers.
• The Color Guide provides information on managing the color output of the Fiery
X3e. It explains how to calibrate your copier/printer and take advantage of the
ColorWise
®
color management system, as well as features in ColorWise Pro Tools
™
.
• The Fiery Color Reference addresses concepts and issues associated with managing
color output of the Fiery X3e and outlines key workflow scenarios. In addition, it
offers information on printing from popular Microsoft Windows and Apple Mac
OS applications.
• The Job Management Guide explains the functions of the job management utilities,
including Command WorkStation
™
, Command WorkStation LE, and DocBuilder
Pro
™
(optional), and how you can use them to monitor and control jobs on the Fiery
X3e. This manual is intended for an operator or administrator, or a user with the
necessary access privileges, who monitors and manages job flow, performs color
calibration, and troubleshoots problems that may arise.
• Release Notes provide last-minute product information and workarounds for some of
the problems you may encounter.

3 About the documentation
Printing the manuals
The PDF files on the User Documentation CD include blank pages to allow for
correct pagination with duplex printing. The CD also includes an installer for Adobe
Acrobat Reader, an application that allows you to view and print the user
documentation from a Windows or Mac OS computer. If your system includes
Acrobat Reader version 5.1 or later, you can view and print these documents directly
from the User Documentation CD. If not, install the version of Acrobat Reader
provided on the User Documentation CD.
T
O INSTALL
A
CROBAT
R
EADER ON A
M
AC
OS
OR
W
INDOWS COMPUTER
1. Insert the User Documentation CD into the CD-ROM drive of your computer.
2. Double-click the CD icon to open the Documentation folder.
3. For Macintosh: Open the Acrobat Reader folder, and then open the Mac folder.
Double-click Reader Installer.
For Windows 98/Me/NT/2000/XP/Server 2003: Open the Acrobat Reader folder, and
then open the Windows folder. Double-click AcroReader51_ENU_full.exe.
When installation is complete, you can view, print, and search the following files:
Configuration Guide , User Software Installation Guide , Printing Guide , Job Management
Guide , Color Guide , and Fiery Color Reference .
N
OTE
:
To view the documentation on your computer, copy the language folder you
want to use to your computer. You can change the name of the folder, if necessary, but
all the manuals must remain in the same folder.

4 Quick Start Guide
System requirements
To install the Fiery X3e user software on a Windows or Mac OS computer,
the computer must be equipped with a built-in or external CD-ROM drive. The
following table lists the minimum system requirements.
Minimum requirements for Windows 98/Me Windows NT 4.0 Windows 2000/
XP/Server 2003 Mac OS
Operating system Windows 98/Me Windows NT with
NT Service Pack 6
Windows 2000 with
Service Pack 3
Windows XP with
Service Pack 1
Windows Server
2003 Standard
Edition, Enterprise
Edition, or
Datacenter Edition,
all the 32-bit version
(printer driver only
supported)
Mac OS 8.6 to 9.2
Mac OS X 10.1 to
10.2 Classic Mode
Mac OS X 10.2.4 or
higher Native Mode
Memory for printing and Fiery
X3e utilities (Fiery
Downloader, ColorWise Pro
Tools, and Fiery Spooler
[Mac OS only])
8MB of RAM for printing
128MB of RAM for printing and utilities
32MB of RAM
for printing
64MB of RAM
for utilities
Networking protocol IPX/SPX, TCP/IP, or AppleTalk AppleTalk (Ether
Talk supported)
TCP/IP
Networking protocol for
Fiery
®
utilities
TCP/IP TCP/IP
N OTE : AppleTalk
can be used for Fiery
Downloader.

5System requirements
PostScript printer driver Adobe PostScript
Printer Driver for
Windows (included
with user software)
Adobe PostScript
Printer Driver for
Windows NT
(included with user
software)
Microsoft PostScript
Printer Driver for
Windows 2000/XP/
Server 2003
(included with
Windows 2000/XP/
Server 2003
operating systems)
The PostScript
Printer Description
(PPD) files for
Windows XP are
provided for
Windows Server
2003
Adobe PostScript
Printer Driver
(included with user
software)
PCL printer driver PCL Printer Driver for Windows only (included with user software) —
EFI Fiery Remote Scan TWAIN-compliant application software
Fiery WebTools
™
•Java-enabled web browser:
—Internet Explorer v5.5 or higher (Windows 98/Me/NT 4.0/2000)
—Internet Explorer v6.0 (Windows 2000/XP/Server 2003)
—Internet Explorer v5.0 for Mac OS
N
OTE
: Microsoft releases frequent updates to its browsers. As support cannot be guaranteed
for all versions, use the versions specified for best results.
•Amonitor and video memory that supports 16-bit color at a minimum resolution
of 800
x
600
•ATCP/IP-enabled network and the IP address or DNS name of the Fiery X3e
•Web Services enabled on the Fiery X3e
Minimum requirements for Windows 98/Me Windows NT 4.0 Windows 2000/
XP/Server 2003 Mac OS

6 Quick Start Guide
Command WorkStation
(Windows only)
•Windows-based computer with a 200-MHz or greater
Pentium processor
• 60MB of available hard disk drive space for installation
•At least 2
x CD-ROM drive
•Amonitor that supports 16-bit color at a minimum resolution
of 1024 x 768
• 128MB of RAM
•Video adapter card with 2MB of video memory
•TCP/IP networking protocol installed
—
Command WorkStation LE
(Mac OS X Native Mode)
• 300Mhz Apple Macintosh G3
• 128MB RAM
• 80MB hard disk drive space (installation)
• 500MB hard disk drive space—recommended for generating full previews of raster files
and handling large PS/PDF files
•Operating system—MAC 10.2.4 or later
•Java for Mac OS X—Java 2 Platform, Standard Edition, version 1.3.1
N
OTE
: More system resources (RAM and hard disk drive space) and a faster processor will
lead to better system performance.
DocBuilder Pro (available as
an option) on Command
WorkStation (Windows only)
In addition to requirements for Command WorkStation:
•Windows-based computer with 333-MHz Pentium processor
• 90MB of available hard disk drive space
•Dongle to be installed on parallel port for every client workstation
—
Parallel port 24MB of RAM 32MB of RAM 64MB of RAM —
Parallel cable included with the Fiery X3e has a DB-25 male connector that connects to the
computer on one end and a DB-25 female connector that connects to the Fiery X3e on the
other end.
Other Network Requirements
UNIX (TCP/IP) workstation • Standard TCP/IP connectivity (for example, Solaris 9 or RedHat Linux version 7.2)
•TCP/IP printing software that conforms to RFC1179 (Berkeley lpd protocol)
IPX (Novell) network • Novell server NetWare software version 5.x or higher
• NDPS gateway in Netware 5.x or higher
•Support for Ethernet SNAP, Ethernet II, Ethernet 802.3, Ethernet 802.2 frame types
Minimum requirements for Windows 98/Me Windows NT 4.0 Windows 2000/
XP/Server 2003 Mac OS

7Preparing to print
Preparing to print
To set up your Fiery X3e, you must perform the following tasks:
• Connect the Fiery X3e physically to a functioning network.
• Configure the network server.
•Set up the Fiery X3e from the Control Panel.
•Prepare client workstations for printing.
A brief explanation of each task follows.
Connecting the Fiery X3e to a functioning network
N
OTE
:
When you add the Fiery X3e to a network, it is assumed that a network
administrator has already installed a network cabling system and has connected
workstations and servers. For examples of different networks, see the Configuration
Guide .
T
O CONNECT THE
F
IERY
X3
E TO A NETWORK
1. Prepare a network node for the Fiery X3e.
2. Route the cable to a location near the copier/printer where the Fiery X3e will be
installed, and attach the cable to the network interface of the Fiery X3e.
For more information, see Chapter 1 of the Configuration Guide .
3. Connect the Fiery X3e to the copier/printer and print a Test Page.
For detailed instructions, see the Configuration Guide .
T
O PREPARE FOR
F
IERY
X3
E CONFIGURATION
1. Print a copier/printer Test Page to verify the copier/printer is functioning normally.
2. Turn off the copier/printer and connect the interface cable from the copier/printer to
the Fiery X3e.

8 Quick Start Guide
3. To confirm this connection, turn on the copier/printer and the Fiery X3e and print a
Test Page from the Fiery X3e Control Panel.
To print a Test Page, press the Utility button on the Control Panel. In the Touch Panel,
press the Controller Detail button. Press the Menu button and select Print Pages.
Choose PS Test Page.
4. With both the copier/printer and the Fiery X3e turned off, connect the network cable
to the Fiery X3e.
The network should be installed and operational.
5. Turn on the copier/printer and the Fiery X3e.
Configuring the network server
If you require a network server, you must configure that server to provide client access
to the Fiery X3e as a color printer. To configure a network server in a Windows or
UNIX network environment, see the Configuration Guide . For Novell and Windows
NT/2000 (using TCP/IP) networks, the network servers must be configured for
printing to the Fiery X3e before you configure Fiery X3e network settings in Setup.
For more information, see the Configuration Guide .
Setting up the Fiery X3e from the Control Panel
Setup configures the Fiery X3e to communicate with other devices and manage print
jobs. You must perform Setup the first time you turn on the Fiery X3e after new system
software is loaded, or any time Server software is reinstalled. Initial Setup must be
performed at the Fiery X3e Control Panel.
Perform the following Setup options in the order listed:
•
Server Setup
—specifies system options.
•
Network Setup
—specifies all the active network systems that transmit print jobs to
the Fiery X3e.
•
Printer Setup
—specifies how print jobs and queues are managed.

9Preparing to print
N OTE
:
This is the minimum setup required to enable your Fiery X3e to begin printing.
To configure network settings in Setup, you need a live network connection so the
Fiery X3e can query the network for zones, servers, and server-based queues.
To perform Setup from the Control Panel, select one menu after another and enter
information about your Fiery X3e and your network and printing environment. In
each Setup screen, the last line of the display shows the name of the current Setup
menu.
The Configuration page lists all the settings in effect in the current Setup. Print a
Configuration page before and after running Setup, to keep a record of current copier/
printer default settings.
T
O PRINT A
C
ONFIGURATION PAGE
1. Make sure the information screen on the Control Panel reads Idle.
If Printing or RIPping appears, the Fiery X3e is processing, and you must wait until
the system finishes and reaches the Idle state.
2. Press the Utility button on the copier Control Panel.
3. In the Touch Panel, press the Controller Detail button.
4. Press the Menu button.
5. Select Print Pages.
6. Choose Configuration.
N
OTE
:
The other pages you can print from the Control Panel include the Test Page,
Font List, Job Log, and color charts. Print the Configuration page after you have
finished running Setup to confirm your settings.
For an introduction to Fiery X3e Setup and detailed instructions on setting up the
Fiery from the Control Panel or a Windows computer, see the Configuration Guide .

10 Quick Start Guide
T
O ACCESS
S
ETUP WHEN THE
F
IERY
X3
E IS READY
1. Make sure the information screen on the Control Panel reads ready.
If Printing or RIPping appears, the Fiery X3e is processing, and you must wait until
the system finishes and reaches the Idle state.
2. Press the Utility button on the copier Control Panel.
3. In the Touch panel, press the Controller Detail button.
4. Press the Menu button.
5. Use the down arrow button to scroll to Run Setup.
At the main Setup window, press the button for the Setup you want to access.
Preparing client workstations for printing
Before you can print to the Fiery X3e, you must install the appropriate printer files
from the User Software CD and connect the client to the Fiery X3e over the network.
The software provided on the User Software CD is described in the User Software
Installation Guide.
NOTE:The steps to set up printing vary slightly for Windows and Mac OS computers.
Windows computers
For all Windows operating systems supported (including Windows 98/Me,
Windows NT 4.0, and Windows 2000/XP/Server 2003), the minimum steps for
setting up printing are as follows:
•Install the printer drivers and corresponding printer driver files.
• Configure installable print options.
• Configure the print connection between the client and the Fiery X3e.

11 Preparing to print
For details, see the User Software Installation Guide. This manual also contains
instructions for the following:
•Installing Fiery utilities
• Configuring the connection for Fiery utilities
• Copying additional files from the User Software CD, as required
Mac OS computers
To set up printing on a Mac OS computer, perform the following steps:
•Install the printer driver and PPD files.
•Set up the Fiery X3e in the Chooser.
• Configure installable print options.
For details, see the User Software Installation Guide. This manual also contains
instructions for the following:
•Installing Fiery utilities
•Installing printer and screen fonts
• Configuring the connection for Fiery utilities
• Copying additional files from the User Software CD as required

12 Quick Start Guide
Shutting down the Fiery X3e
Generally, you can leave the Fiery X3e and the copier/printer running all the time.
This section describes how to shut down the Fiery X3e when necessary.
Shutting down the Fiery X3e
You may need to shut down the Fiery X3e for service. When you do so, fonts that have
been downloaded to the hard disk drive are not deleted. Print jobs in the Hold queue,
the Printed queue, and jobs that have been processed but not printed are not deleted;
they will be available for printing when you restart the Fiery X3e.
TOSHUT DOWN THE FIERY X3ECOPIER
1. Make sure that no jobs are being processed or printed (the activity light should
be off).
2. Press the Utility button on the copier Control Panel.
3. In the Touch Panel, press the Controller Detail button.
4. Press the Menu button.
5. Use the down arrow to scroll to Shut Down.
6. Select Shut Down System.
A message will be displayed when it is safe to power off the system.
7. Turn off the Fiery X3e using the Fiery X3e power switch.
8. Turn off the copier using its main power switch.
NOTE:After turning off the copier, wait at least three seconds before turning it back on.

13 Safety warnings
TOSHUT DOWN THE FIERY X3EPRINTER
1. On the printer Control Panel, press the Menu key to display the Functions menu.
2. Scroll to display Shut Down and press the Set key.
3. Scroll to display Shut Down System and press the Set key.
A message will be displayed when it is safe to power off the system.
4. Turn off the Fiery X3e using the Fiery X3e power switch.
NOTE:If you are recycling power, wait at least ten seconds before powering back on.
5. Turn off the print engine using its main power switch.
Safety warnings
The Fiery X3e display window is a liquid crystal display (LCD) that is made of glass
and can break. Do not subject it to strong shocks.
If the display window breaks and the liquid crystal material leaks out, do not inhale,
ingest, or touch it. If the material gets on your skin or clothing, wash it off with soap
and water immediately.
Do not touch or put pressure on the panel. This will change the color of the panel.
Cleaning the Fiery X3e display window
Clean the Fiery X3e with a soft cloth moistened with isopropyl alcohol or ethyl
alcohol. Never use water or ketone, as these may permanently alter the display.

14 Quick Start Guide
Summary of Fiery X3e network installation
Fiery X3e
At each workstation that will print to the Fiery
X3e:
•Install the appropriate printer files and connect
to one or more queues.
•For computers that will use them, install Fiery
utilities and an Internet browser.
•Verify the Fiery X3e in the list of printers and
run a test print.
Fiery X3e available on the network
Network server
UNIX Mac OS Windows
Fiery X3e Prepare a network node. Connect the Fiery X3e to
the network.
Configure UNIX, Windows NT 4.0/2000/Server
2003, and IPX (Novell) servers to specify Fiery
X3e print queues and Fiery X3e users.
No special configuration of AppleShare servers
is required.
On the Fiery X3e Control Panel, configure at least
the Server Setup, Network Setup, and Printer
Setup.
Server configuration
Connection
Client setup
Fiery X3e setup