FireAngel W2-SVP-630 User manual

This product may be purchased from Connevans Limited
secure online store at www.DeafEquipment.co.uk
DeafEquipment.co.uk
Offering you choice
Helping you choose
Connevans.info
Solutions to improve the quality of life

User Manual
COMBINED STROBE
& VIBRATING PAD
W2-SVP-630
Please read me – as I could save your life.
Please retain this user manual for future reference

Keeping you safe from  re and carbon monoxide
For a full range of smoke alarms and carbon monoxide alarms
visit www. reangel.co.uk

CONTENTS
Note: This User Manual is also available in large text and other
formats. Please call 0800 141 2561 for further information
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . 2
KEY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLING THE STROBE AND VIBRATING PAD . . . . . . . 4
CONNECTING THE BATTERY/MAINS POWER . . . . . . . . . 4
WIRELESSLY INTERLINKING THE
WI-SAFE 2 STROBE AND PAD TO YOUR
WI-SAFE 2 SMOKE OR CO ALARM . . . . . . . . . . . . . . . 6
TESTING THE WI-SAFE 2 STROBE AND
VIBRATING PAD WITH SMOKE/CO ALARMS . . . . . . . . . 7
POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTALLING THE STROBE . . . . . . . . . . . . . . . . . . . . 10
LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
UNPLUGGING FROM THE MAINS/POWER CUT . . . . . . 13
PRODUCT INDICATORS (LEDS) . . . . . . . . . . . . . . . . 14
WHAT TO DO IF YOUR STROBE AND
VIBRATING PAD GOES INTO ALARM . . . . . . . . . . . . . 15
WHAT TO DO IN THE EVENT OF
A SMOKE ALARM TRIGGERING
THE STROBE AND PAD . . . . . . . . . . . . . . . . . . . . . 16
WHAT TO DO IN THE EVENT OF
A CARBON MONOXIDE ALARM
TRIGGERING THE STROBE AND PAD . . . . . . . . . . . . . 17
REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . 19
DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RETURNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PRODUCT RANGE . . . . . . . . . . . . . . . . . . . . . . . . 21

2
INTRODUCTION
KEY FEATURES
IMPORTANT: If you are installing this product for
use by others, you must leave this manual (or a
copy of it) for the end user.
Wi-Safe 2 is the very latest in wireless technology from
Sprue Safety Products. It provides a network of wireless
radio frequency (RF) communication which can trigger
Wi-Safe 2 Alert products to alarm in the event of danger.
This Strobe and Vibrating Pad, when interlinked with
Wi-Safe 2 enabled Smoke alarms and/or Wi-safe 2
enabled Carbon Monoxide (CO) Alarms (purchased
separately) will provide warning of danger from smoke
and/or carbon monoxide.
In addition to the audible sound from the Smoke (or
CO) alarm, the ashing Strobe and Vibrating Pad will be
triggered to alert someone who may not be able to hear
the audible alarm. The ashing strobe provides a visual
warning for waking hours, while the vibrating pad is
designed to be placed under a pillow or a mattress and
is suitable for waking an individual to alert them when a
smoke alarm sounds. If placed under a mattress, ensure
the thickness of the mattress does not cushion the pad
to the extent it cannot be felt adequately.
• Uses Wi-Safe 2 technology to provide warning of re
or Carbon Monoxide (CO). Wi-Safe 2 products can
be interlinked to create a network, meaning if smoke
or CO triggers any alarm in the network, all other
networked alarms and ancillary devices activate.
• When used with Wi-Safe 2 enabled Smoke and/or CO
alarms, the kit provides additional protection when
sound alone may not be enough.
• Provides a simple two button press “learn in” process

3
to wirelessly interlink with Wi-Safe 2 smoke alarms or
CO alarms.
• The Strobe provides a remote low level testing
facility for testing interlinked smoke and CO alarms,
avoiding the need to reach up to ceiling mounted
alarms to test.
• Mains powered with rechargable battery back-up
(must be replaced after 5 years).
• The Strobe will detect and demonstrate a fault or low
battery warning with any smoke alarm or CO alarm
within the inter-linked network.
• The Strobe is suitable for wall mounting with 2 screw
xings or free standing.
• Designed for use with Smoke alarms and Carbon
Monoxide alarms from the Wi-Safe 2 range
(purchased separately).
Wi-Safe 2 Strobe and Vibrating Pad Pack contains:
1. CP-STROBE - Strobe light with integrated control
unit (referred to as “strobe”)
2. CP-VPAD - Vibrating pad to be placed under pillow
or chair (referred to as ”pad”)
3. AD-DC12V05A - AC mains adaptor, 12v, 0.5A
rated output
4. B-450L - Replaceable, rechargeable 5 year
life battery
5. Wall xing screws
NOTE: The Strobe and Vibrating Pad is only compatible
with Wi-Safe 2 alarms from Sprue Safety Products. It
cannot be wirelessly interlinked with other models or
brands of smoke alarms or carbon monoxide alarms.
It is not compatible with products from Sprue Safety
Products original Wi-Safe range.
The Wi-Safe 2 product range is currently being
expanded. Please visit www.reangel.co.uk for
details of the latest additions to the portfolio.

4
INSTALLING THE STROBE
AND VIBRATING PAD CONNECTING THE BATTERY/MAINS POWER
PREPARATION: Please ensure you have read and
understood this entire manual before installing your Strobe
and Vibrating Pad.
Your Strobe and Vibrating Pad is designed to be used in
conjunction with Smoke alarm(s) and CO alarm(s) from
the Wi-Safe 2 range of products. It is recommended that
for optimum protection from smoke and/or carbon
monoxide, one Wi-Safe 2 smoke alarm is tted in each
living room of your home, including bedrooms, and one
Wi-Safe 2 CO alarm is tted in every room containing a fossil
fuel appliance, connected to your Strobe and Vibrating Pad.
NOTE: Up to fty Wi-Safe 2 enabled Smoke alarms, CO
alarms and/or Wi-Safe 2 accessories can be interlinked
(“learned in”) to a single network
Ensure all smoke alarms and/or CO alarms to be used
are installed, tested and working correctly as per the
instructions in their respective user manuals.
It is possible to use the strobe independently. For further
details please contact Technical Support on: 0800 141 2561
NOTE: The Strobe and Vibrating Pad requires both a
continuously powered AC (mains) electrical supply
and internal battery for its normal operation. The
battery accompanying this product is rechargeable and
charges when there is mains power to the Strobe.
1. Plug the Vibrating Pad connector into the Strobe
(as shown in g1) Route the wires through the wire
guide.
fig1

5
NOTE: When power is rst provided to the Strobe,
the amber LED and both red LEDs will ash twice and
the unit will ‘bleep’ three times; the amber LED will
then illuminate continuously to indicate that the unit
has not been “learned in” to any network. Both alarm
LED’s (smoke and CO) will extinguish. This will typically
happen when the battery is connected. If the battery
does not retain any residual charge, it will happen when
the mains power is connected.
2. Remove the battery cover on the back of the Strobe
by pulling back the clip to release. Connect the
rechargeable battery, by aligning the terminals
(red wire to red wire) and clipping the connectors
together. You may hear the Strobe chirp as you do
this.
7. Plug the mains adaptor into a 230V socket and
turn the power on. The green power LED should
illuminate.
6. Plug the power cable in to the Strobe. Route the
wire through the wire guide (g3).
3. Place the battery into the recess. NB: the battery
cable needs to be positioned underneath the
battery. Place the cable at the bottom of the recess
with the battery lying over the top with the text
on the battery face down. This will ensure that the
battery is installed correctly.
5. Assemble the power cable and adaptor by
positioning the plug head as shown. Rotate onto the
adaptor clockwise until it clicks into position. (g2)
4. Replace the battery cover.
CAUTION: Connect the battery with mains
power disconnected.
fig2 fig3

6
WIRELESSLY INTERLINKING
THE WI-SAFE 2 STROBE AND
VIBRATING PAD TO YOUR
WI-SAFE 2 SMOKE OR CO ALARM
It is recommended that you read through these “learn
in” instructions before starting.
Learning a Strobe into a new Wi-safe 2 system:
Learning a strobe into an existing Wi-Safe 2 system:
1. Place one of your Smoke or CO alarms on to its
baseplate. You will use this product to interlink with
the strobe to create a network.
2. Briey push and release the learn button located in
a circular hole in the back of the Strobe, using a ball
point pen or similar pointed instrument (g4). 1. Locate a Smoke / CO alarm that is already part of the
existing Wi-Safe 2 system. You will use this product
when adding the strobe into the network
2. Follow steps from point 2 above
3. After pressing this button, the two Alarm (red) LEDs
on the front of the unit will ash and then illuminate
for 5 seconds.
4. During this period, while the red LEDs are
illuminated, press the test/reset button on the
Smoke or CO alarm to wirelessly interlink the two
products.The Smoke alarm (or CO alarm) will emit
an audible signal, and the red (Alarm) LED on the
Smoke (or CO alarm) will also ash.
5. After learning in the Strobe and Vibrating Pad into
the alarms, test the units individually to ensure they
are wirelessly interlinked (see below)
To add any further alarms to the network, press the
learn button on the new alarm then the test button on
the Strobe, or on any alarm already learned in to the
network.
fig4

7
NOTE: The battery is supplied in a discharged or
partially discharged state and will require up to 24
hours of charging (continuous connection to the
mains supply) to ensure that it is fully charged. During
this period the amber fault LED may ash once every
ve seconds to indicate that the battery is low. The
following tests however may be carried out before the
charging is complete.
Further Wi-Safe 2 products (including additional
Strobes) can be learned into the network in the same
way. The learn button on the Strobe is located on the
back of the product.
NOTE: The amber fault LED will also ash (once per
second) if the Vibrating pad is not correctly installed.
After learning in the Strobe and Vibrating Pad into the
alarms, test the units individually to ensure they are
wirelessly interlinked (see next section)
To remove (“unlearn”) the Strobe from the wireless
network:
1. Briey push and release the learn button located in
the circular hole in the back of the Strobe as shown
(g 4). The two red alarm LEDs on the front of the
Strobe will illuminate as you push the button.
2. Push and hold the learn button a second time. The
red alarm LEDs will illuminate. Hold the button until
the red alarm LEDs extinguish.
3. The red alarm LEDs will then perform a sequence of
two long and three short ashes. The yellow fault
LED will illuminate continuously to conrm that the
the Strobe is no longer interlinked to the wireless
network.
4. Press the test button on the Strobe. It should not
cause other Wi-Safe 2 alarms to sound. However,
if the Strobe is still interlinked, repeat the above
procedure.
IMPORTANT: If you wish to remove the Strobe
and Vibrating Pad from the wireless network, it
is important to “unlearn” the unit from the network.
Failure to do so means that the unit continues to try
and communicate with the removed unit, and will
result in a system fault.

8
Strobe: The strobe will ash and the corresponding red
(alarm) LED will also ash
Vibrating Pad: The Vibrating Pad will vibrate.
Repeat the procedure with all alarms in the wireless
network.
Testing the network from the Strobe
Briey press the test button on the strobe and release.
The Strobe will ash, and the Vibrating Pad will vibrate.
At the same time any alarm that is wirelessly interlinked
(“learned in”) to the network will also sound, the sound
pattern on each alarm corresponding to its type (smoke
or CO – see previous section). The ashing Strobe and
Vibrating Pad will be activated for the length of time
that the alarms sound. Both red (alarm) LEDs on the
Strobe will ash for a short time.
This conrms that the units are wirelessly interlinked.
Weekly Testing
It is recommended that a self-test of all the units in your
Wi-Safe 2 network is carried out weekly.
TESTING THE WI-SAFE 2 STROBE
AND VIBRATING PAD WITH
SMOKE/CO ALARMS
Testing the network from the Smoke Alarm or CO
alarm
Briey press the test button on the smoke alarm or CO
alarm and release (g5). The alarm will give an audible
sound (consisting of 2 cycles of 3 loud beeps on smoke
alarms, 2 cycles of 4 rapid beeps on CO alarms), then
stop automatically. The red (alarm) LED on the alarm
will ash rapidly during the audible signal. Any other
wirelessly interlinked alarms which are also part of the
network will also give an audible alarm, and then stop
automatically.
fig5

9
In addition the network should also be tested whenever:
• An additional alarm or ancillary product is added to
the system
• There are changes to the structure of your property
• There are signicant changes in the position of large
items of furniture or electrical products in your home
• You replace the battery in any product within the
Wi-Safe 2 network.
The Strobe and Vibrating Pad are now ready to be
placed into position.
If you are testing the Strobe and Vibrating Pad for the
rst time during installation and they do not test, please
repeat the “learn in procedure.”
If you are unable to resolve the problem, please contact
Technical Support on 0800 141 2561,
This product has been fully tested. However, as with any
electronic product, it could fail and may not produce
an indication of smoke or CO within su󱐰cient time to
alert you of the danger and provide adequate time for
your escape. In order to maximise your level of safety,
always test your Strobe and Vibrating Pad and all alarms
in the Wi-Safe 2 network system every week to ensure
the whole system is in full working order and that the
wireless interlink (RF) between the alarms and ancillary
products has not been compromised.
NOTE: The Strobe and Vibrating Pad, smoke and CO
alarms should not be considered as a substitute for life
or property insurance. The Strobe and Vibrating Pad
System should be replaced immediately in the event
of failure, and the rechargeable battery should be
replaced every 5 years.
Where should the Strobe and Vibrating Pad be
installed?
If you have one Strobe and Vibrating Pad, it should
be installed in the main room where you sleep. You
may wirelessly interlink additional strobes and pads
to the network and install them in any room where
you may need to be alerted in the event of an alarm.
POSITIONING

10
placed securely and cannot fall out – ideally within the
pillowcase or cushion cover.
Position the Strobe:
• Close to a power socket where it can be easily
plugged in and the cable does not create a
tripping hazard.
• Where you can see the Strobe ashing from
anywhere in the room
• Where you can see the LEDs on the front of the unit
• Ensure that the Vibrating Pad cable can easily reach
its position under the chosen pillow/cushion
NOTE: The Strobe can be tted to a wall OR it can be
placed on a table.
CAUTION: Do not put the Strobe and Vibrating Pad:
• Outside the building
• In a damp or humid area
• In an area where the temperature could regularly
drop below –5°C or rise above 40°C
• Anywhere where the units can easily be knocked
or damaged
It is important that if you install additional Strobes and
Vibrating Pads you test each of these upon installation
to check they are “learned in” to the rest of the network.
Wireless Range: The wireless range of Wi-Safe 2
products is over 200 metres in clear air/clear line of
sight.
However it is recommended not to exceed 35m as the
maximum distance between any interlinked Wi-Safe
2 smoke alarm or carbon monoxide alarm from the
Strobe and Vibrating Pad. This is because the range
can be reduced by walls, and other obstructions in the
building.
Position the Vibrating Pad:
• Under your pillow
• Under a cushion on a chair where you are likely
to fall asleep
Test and check that the Vibrating Pad can be felt in all
circumstances where you may fall asleep. Ensure it is

11
INSTALLING THE STROBE
Make sure the Strobe is visible from anywhere in
the room.
To wall mount the Strobe drill two suitably sized holes
64mm apart, centre to centre, using the template (g6)
(Warning - make sure that you check for electrical
cabling and pipework hidden in the wall before
carrying out any drilling). In the pack you will nd two
screws and two screw anchors. Push the screw anchors
(if needed) into the drill holes and secure the screw
leaving the heads protruding so that the face of the
head is 5mm away from the wall. Now hook the Strobe
onto the screws (see below).
If placing the Strobe on a table
instead of mounting on the wall,
make sure it cannot be easily
knocked or slide o󱐯. The green
‘Power’ LED should illuminate
continuously to show that the AC
power supply is connected.
64mm
Drill hole spacing
fig6

12
DANGER: Under no circumstances should this product
be immersed in water, or used in an area where water
may come into contact with the product.
OPERATION
1. Standby Mode, but not “learned in” to a network.
The amber (fault) LED will be illuminated.
2. Standby mode
The Strobe should be connected to the mains AC
supply with the Vibrating Pad connected, and placed
in a suitable position. The Green “power” LED on the
strobe will be permanently illuminated.
3. Alarm mode
Strobe – Flashing strobe and either smoke or CO red
(alarm) LED ashing - Alarm
Pad – Vibration warning
When a Wi-Safe smoke or carbon monoxide alarm goes
into “alarm” mode the RESPECTIVE red alarm LED will
illuminate, the Strobe will continuously ash and the
Vibrating Pad will continuously vibrate.
LIMITATIONS
NOTE: This Strobe and Vibrating Pad is not compatible
with products from the original Wi-Safe product range.
• The Strobe and Vibrating Pad will not operate in
isolation, with non Wi-Safe 2 Alarms, or any alarms
made by other manufacturers.
• The separate units making up the Strobe and
Vibrating Pad cannot be interchanged with those of
other manufacturers and an attempt to do this may
render the whole system unsafe. Do not connect any
other product to the Strobe.
• The Strobe and Vibrating Pad may not respond to
the signal from a Wi-Safe 2 alarm if the alarm and the
Strobe containing the control box are too far apart
(see positioning).
• The Strobe and Vibrating Pad may not respond
to the signal from a Wi-Safe 2 alarm if there are
obstructions that signicantly reduce the signal
(e.g.: steel reinforcement in concrete). Always test
the operation of the Strobe and Vibrating Pad with
all other alarms and units in the network after any
changes to the building structure or in the position
of large items of furniture.

13
UNPLUGGING FROM THE
MAINS/POWER CUT
The way in which the Strobe and Pad alerts a warning
is the same for both alarm types, i.e. the Strobe will
ash and the Pad will vibrate in exactly the same way,
irrespective of whether the alarm is triggered by a
smoke alarm or a CO alarm.
If both smoke and CO alarms are in “alarm” mode, only
the smoke LED will ash.
NOTE: The Strobe will stop ashing, the red LED will
cease to ash and the Vibrating Pad will stop vibrating
when the alarm sending the signal has been reset or
has stopped if the danger is no longer present.
Only reset an alarm if you are certain there is no
imminent danger from Fire or Carbon Monoxide.
Locate Feature
When the network is in alarm mode, pressing the test
button on any unit in the network will silence all other
alarms in the network, for a period of 2 minutes, except
the alarm that has sensed smoke or carbon monoxide.
This will enable the instigating alarm to be identied/
located. If necessary, the instigating alarm can then be
silenced.
The Strobe and Pad is designed to be mains powered.
The internal rechargeable battery will still provide
power if the mains is disconnected. A fully charged
battery will allow the Strobe and Pad to continue to
operate for three days. NB: Only use the battery supplied
in the pack or a genuine FireAngel replacement. Other
rechargeable batteries may damage the equipment or
create a safety hazard.
WARNING: When the mains power is disconnected,
the green power LED will no longer illuminate and the
amber (fault) LED will double ash every 5 seconds.
Plug the Strobe back into the mains as soon as possible
to recharge the battery and maintain operation.
If the amber LED is ashing once every 5 seconds
when the green power LED is o󱐯 then URGENTLY
restore power to unit as battery status is very low, and
may fail to operate in an alarm situation.
NOTE: Once the Strobe is plugged back into the mains,
the amber (fault) LED will continue to ash once every
5 seconds until the battery has fully recharged.

14
PRODUCT INDICATORS (LEDS)
STATUS STROBE/PAD
ACTIVITY
POWER
GREEN
SMOKE
RED
FAULT
AMBER
CO
RED
ACTION
NEEDED
Standby mode Illuminated None required
Mains not
connected
or on battery
power
Double ash every
ve seconds
Reconnect Strobe
to mains power
Vibrating pad
not connected to
strobe
Illuminated
(providing Strobe is
plugged into mains)
Flashing once per
second
Reconnect
vibrating pad to
strobe
Mains not
connected and
battery capacity
low
Strobe will chirp Flashing once
every 5 secs
URGENTLY restore
power to unit as
battery status is
very low.
Alarm mode
Smoke
Strobe ashing/
pad vibrating
Illuminated
(providing Strobe is
plugged into mains)
Flashing
Alarm – CO –
Open windows
and evacuate
property
Alarm mode
CO
Strobe ashing/
pad vibrating
Illuminated
(providing Strobe is
plugged into mains)
Flashing
Alarm – CO –
Open windows
and evacuate
property

15
STATUS STROBE/PAD
ACTIVITY
POWER
GREEN
SMOKE
RED
FAULT
AMBER
CO
RED
ACTION
NEEDED
Unit fault
Illuminated
(providing Strobe is
plugged into mains)
Flashes rapidly Contact technical
support
Network fault Double ash every
1 sec
Ensure every
alarm and WiSafe
2 device is tted
correctly and
working
Not Learned in Illuminated Follow learn in
procedure
Powering up
Strobe Unit will
chirp with beep
sequence
Double ash (not
repeated)
Double ash (not
repeated)
Double ash (not
repeated) None required
WHAT TO DO IF YOUR
STROBE AND VIBRATING PAD GOES INTO ALARM
CAUTION: In all circumstances assume your Strobe and
Vibrating Alert is responding to a real alarm situation
that has been triggered by either a smoke alarm or
carbon monoxide alarm.
The type of incident triggering the Strobe and
Vibrating Pad to go into alarm is indicated on the
Strobe:
Smoke Alert
The Smoke (red) LED will ash
Carbon Monoxide Alert
The CO (red) LED will ash
Smoke and CO Alert
The Smoke LED (red) will ash

16
WHAT TO DO IN THE EVENT OF A
SMOKE ALARM TRIGGERING THE
STROBE AND PAD
What to do in Case of Fire in your Home
If you have made a family escape plan and practiced it
with your family, you have increased their chances of
escaping safely. Go over the following rules with your
children each time you have a re drill. This will help
everyone remember them in case of a real emergency.
• Don’t panic; stay calm. Your safe escape may depend
on thinking clearly and remembering what you have
practiced.
• Notify every member in the residence of the re.
• Get out of the house as quickly as possible. Follow
a planned escape route. Do not stop to collect
anything or to get dressed.
• Feel the doors to see if they are hot. If they are hot,
do not open them - use an alternative escape route.
• Stay close to the oor. Smoke and hot gases rise.
• Cover your nose and mouth with a cloth (wet if
possible). Take short, shallow breaths.
• Keep doors and windows closed. Open them only if
you have to in order to escape.
• Meet at your planned meeting place after leaving the
house. Carry out a head count.
• Call the re service on 999 as soon as possible from
outside your house. If possible use a neighbour’s
phone or call box rather than a mobile phone (as the
location can be traced from the number if the line is
lost).
• Give the address and your name.
• Never go back inside the building until a member of
the re service has told you it is safe to do so. If after
proceeding with extreme caution you have been
able to conrm that your Strobe and Vibrating Alert
System was triggered by a nuisance alarm (which
may occur from time to time from cooking or other
non-emergency situations) you should silence the
smoke alarm that has been triggered. This will stop
the Vibrating Pad from vibrating and the strobe from
ashing. It is important to practice escape plans and
show everyone in the house, including children,
what to do in the event of an alarm.

17
WHAT TO DO IN THE EVENT
OF A CARBON MONOXIDE
ALARM TRIGGERING THE
STROBE AND PAD
Contact your local re service. They will give you more
ideas about how to make your home safer from res
and how to plan your family’s escape.
Assume Carbon Monoxide has been detected in your
home
WHAT TO DO IN THE EVENT OF A CO ALARM
WARNING: A loud alarm is a warning that unusually
high and potentially lethal levels of carbon monoxide
are present. Never ignore this alarm; further exposure
could be fatal. Immediately check residents for
symptoms of carbon monoxide poisoning, (see product
manual) and contact the proper authorities to resolve
all CO problems.
NEVER IGNORE ANY ALARM.
What to do during an alarm
• Keep calm and open the doors and windows to
ventilate the property
• Stop using all fuel burning appliances and ensure,
if possible, that they are turned o󱐯
• Evacuate the property leaving the doors and
windows open
• Ring your gas or other fuel supplier on their
emergency number; keep the number in a
prominent place
• Do not re-enter the property until the alarm
has stopped. When exposed to fresh air it can
take up to 10 minutes for the sensor to clear and
the alarm to stop depending on the level of
carbon monoxide detected
• Get medical help immediately for anyone su󱐯ering
the e󱐯ects of carbon monoxide poisoning
(headache, nausea, drowsiness), and advise that
carbon monoxide poisoning is suspected
• Do not use the appliances again until they have
been checked by an expert. Contact a Gas Safe
registered engineer in the case of a gas appliance.