Firefly MV IEEE-1394a Digital Camera User manual

Getting Started
Firefly®MV IEEE-1394a Digital Camera
The following items are included with your Firefly MV
Development Accessory Kit
• 2 meter, 6-pin to 6-pin, ultra-thin IEEE-1394 cable
• IEEE-1394 OHCI PCI Host Adapter 3 port-400 Mbps card
• Male GPIO connector pre-wired for quick and easy access
• FlyCapture®SDK (C/C++ API and device drivers) CD
FIREFLY®MV SPECIFICATIONS
IMAGE ACQUISITION
CAMERA AND DEVICE CONTROL
CAMERA INTERFACE
STANDARD IMAGE FORMATS
TECHNICAL DRAWINGS
IMAGE PROCESSING
Mode Description Frames Per Second
1.875 3.75 7.5 15 30 60
640x480 Y8 (8bpp) ••• •
640x480 Y16 (16bpp) •••
PARTIAL IMAGE FORMATS (FORMAT_7)
STATUS LED
SPECIFICATION FFMV-03MTM/C (BW or Color)
Image Sensor Type 1/3” progressive scan CMOS
Shutter Type G l o b a l s h u t t e r u s i n g M i c r o n T r u e S N A P ™ t e c h n o l o g y
Image Sensor Model M i c r o n M T 9 V 0 2 2
Maximum Resolution 75 2 (H ) x 4 8 0 ( V )
Pixel Size 6 .0 μ m x 6 .0 μ m
Analog-to-Digital Converter O n- c hi p 10 - b it A D C
Video Data Output 8 and 16-bit digital data
Image Data Formats Y8, Y16 (monochrome), 8-bit and 16-bit raw Bayer data (color models)
Digital Interface 6-pin IEEE 1394a for camera control, video data, power
Tran sfer Ra t es 400 Mb/s
Maximum Frame Rate 752x480 at 61 FPS • 320x240 at 112 FPS (region of interest)
320x240 at 122 FPS (2 x 2 pixel binning)
Partial Image Modes pixel binning and region of interest modes via Format_7
General Purpose I/O Ports 7-pin JST GPIO connector, 4 pins for trigger and strobe, 1 pin +3.3 V, 1 Vext pin for
external power
Gain Control automatic / manual, 0 dB to 12 dB
Shutter Speed aut om atic / m an ual , 0.12 m s to 512 m s
Gamma 0 to 1 (enables 12-bit to 10-bit companding)
Synchronization via external trigger, software
trigger (on same bus only), or free-running1
External Trigger Modes IIDC v1.31 Trigger Modes 0 and 3
Power Requirements 8 to 30 V via IEEE-1394, less than one (1) Watt
Dimensions (L x W x H) 24.4 x 44 x 34 mm
Mass 37 g (including tripod adapter)
Camera Specications IIDC 1394-based Digital Camera Specication v1.31
Memory Storage three memory channels for user congurable power-up settings
Lens Mount CS-mount (5mm C-mount adapter included) • M12 microlense mount2
Compliance CE, FCC Class B, RoHS
Operating Temperature 0° to 45°C
Storage Temperature -30° to 60°C
2 For qualied OEMs
1 Using standard non-Format_7 video formats and modes operating at 30 FPS and 60 FPS only.
Global Shutter Photodiode pixels with simultaneous integration and readout
Near-IR Performance Enhanced performance provides NIR QE greater than 35%
Auto Exposure Control Ensures optimal auto settings of shutter and gain for each image
Fast Frame Rates Faster standard frame rates up to 60 FPS
Partial Image Modes Format_7 modes for fast frame rates and higher signal-to-noise
Multiple Trigger Modes Standard external trigger mode, skip frames mode
Gain and Brightness Adjust gain and black clamp via a 10-bit A/D converter
ADC On-Chip 10-bit linear or 12-bit to 10-bit companding mode via Gamma
Image Flip Horizontal image flipping (mirror image)
Embedded Image Info Pixels contain image timestamp (1394 cycle time)
Memory Channels Non-volatile storage of camera default power-up settings
Strobe Output Strobe output with configurable delay and duration
Absolute Value Controls Shutter and gain reported in real-world units (seconds and dB)
Broadcast Properties Camera responds to broadcast register writes on the same bus
Camera Upgrades Firmware upgradeable in field via IEEE-1394 interface.
IEEE-1394 Connector
The Firey®MV has a standard 6-pin IEEE-1394 connector that is used for data transmission, camera control and
powering the camera.
Cables
The maximum 1394 cable length between any 1394 node (e.g. camera to PCI card, card to hub, etc.) is 4.5m, as
specied by the IEEE-1394 standard. Use standard, shielded twisted pair copper cables.
General Purpose I/O Connector
The Firey MV has a 7-pin GPIO connector on the back of the case.The connector is made by JST (Mfg P/N:
BM07B-SRSS-TB).The Development Kit contents include a pre-wired female connector (Point Grey P/N:ACC-01-
3002); refer to the diagram below for wire color-coding.Additional female connectors (JST Mfg
P/N: SHR-07V-S-B) can be purchased from Digikey (P/N: 455-1382-ND).
The Firey MV GPIO pins areTTL 3.3V pins. Inputs can be congured to accept external trigger signals.When
congured as inputs, the pins are internally pulled high using weak pull-up resistors to allow easy triggering of the
camera by simply shorting the pin to ground (GND). Inputs can also be directly driven from a 3.3V or 5V logic
output.The inputs are protected from both over and under voltage. It is recommended, however, that they only be
connected to 5V or 3.3V digital logic signals. Outputs can be congured to send an output signal or strobe pulse.
When congured as outputs, each line can sink 10mA of current.
44.0
34.0
22.0
33.5
6.8
26.4 17.0
STATUS LED GPIO C
O
1394a CONNECTOR
22.0
12.0
3.6
4x HOLES FOR M2 THREAD FORMING SCREW
0.3 18.9 12.6
LENS MOUNT
18.9 0.3 12.6
LENS MO
U
22.0
12.0
3.6
4x HOLES FOR M2 THREAD FORMING S
44.0
34.0
1394A CONNECTOR
1.6
16.5
4.9
3.4
SIDE VIEW
FRONT VIEW
IMAGE SENSOR
21.7
12.5
20.010.0
PCB MOUNTING HOLES
2.1 THRU
40.0
1.7 36.7
20.0
1.7
25.0
2.1 THRU
LENS HOLDER MOUNTING HOLES
12-BIT TO 10-BIT COMPANDING
A gamma value of 0 yields a linear response; a value of 1 puts the camera into 12-bit to 10-bit mode. This
mode allows higher ADC resolution (12 bits) for low-level signals (shadow details) and lower ADC resolution
(9 bits) for high-level signals (highlight details).
"IT2ESOLUTION
"IT2ESOLUTION
"IT2ESOLUTION






"IT
#ODES
"IT
#ODES
"IT2ESOLUTION

SPECTRAL RESPONSE (QE)
Diagram Pin Function Description
1 Vext Power camera externally
2 +3.3V Power external circuitry up to a total of 150mA
3 IO0 Input / Output (Default Trigger_Src)
4 IO1 Input / Output
5 IO2 Input / Output / RS232 Transmit (TX)
6 IO3 Input / Output / RS232 Receive (RX)
7 GND
To configure the GPIO pins, consult the “General Purpose Input / Output”
section of the PGR IEEE-1394 Digital Camera Register Reference.
Pre-wired GPIO cable

green green red white
black
green
green
FFMV-03MT / FMVU-03MT
Mode Pixel Format Size FPS Description
0 Mono8 (8bpp) 752x480 61 Region of interest (ROI)
0 Mono8 (8bpp) 320x240 112 Region of interest (ROI)
0 Mono8 (8bpp) 160x120 190 Region of interest (ROI)
1 Mono8 (8bpp) 320x240 122* 2x2 pixel binning
2 Mono8 (8bpp) 640x240 122* 1x2 pixel binning
Steady on Receiving power and successful camera initialization
Steady on and very bright Acquiring / transmitting images
Flashing bright, then brighter Camera registers being accessed (no image acquisition)
Steady or slow flashing on and off Camera firmware updated (requires power cycle),
or possible camera problem
April 2011
*Black and white output only. Color data is removed due to pixel binning.

The FlyCapture®User Guide and other technical references can
be found in the Programs > Point Grey Research > PGR FlyCapture >
Documentation directory. Our on-line Knowledge Base (www.ptgrey.com/
support/kb/) also addresses the following problems:
• Article 21:Troublesome hardware configurations
• Article 88:Vertical bleeding or smearing from a saturated portion of an image
• Article 91: PGR camera not recognized by system and not listed in Device Manager
• Article 93: My laptop’s IEEE-1394 port or PCMCIA card doesn’t supply power to my camera
• Article 145: Image discontinuities or horizontal tearing of images when displayed on monitor
• Article 171: Performance of 1394 devices may decrease after installing Windows XP SP2
• Article 188: Image data acquired by my camera is corrupt and displayed images are broken
• Article 189: Image capture freezes after a period of successful image capture.
Installation
1 2
3
4
Installation
Installation
Troubleshooting
3. Install the IEEE-1394 PCI card
• Turn the computer back on and log into Windows.
• In most cases, the Windows IEEE-1394 drivers will be automatically
installed for the card,with no user input required. However, in some cases
the Found New Hardware Wizard will appear. Follow the prompts
given by the Wizard to install the card.
• Open Windows Device Manager by going to the
Control Panel > System > Hardware tab > Device Manager. Ensure
the PCI card is properly installed as an IEEE 1394 Bus host controller.
4. Install the FlyCapture®Software and Drivers
• Follow the installation instructions to install the software.
• A dialog will appear asking if you want to downgrade your Windows XP
drivers. If you have installed Service Pack 2, we encourage users to do this.
See this Knowledge Base article for further information:
www.ptgrey.com/support/kb/index.asp?a=4&q=171
5. Installing theTripod Mounting Bracket (optional)
• The mounting bracket for the Firefly®MV attaches to the camera using
the included M2 screws.
6. Connect the 1394 PCI Card and Cable to the camera
• Plug the 4.5 meter, 6-pin to 6-pin, IEEE-1394 cable into the 1394 PCI
card and the Firefly MV 1394 Connector.
NOTE: The camera relies on the 6-pin 1394 cable to provide power. If
using an interface card other than that provided, ensure that adequate
power is provided.
• If the Microsoft Windows “Found New Hardware Wizard”appears,
proceed to Step 7. Otherwise, proceed to Step 8.
7. Install the PGRCAM Driver
• Click “Install from a list or specific location”and click “Next”.
• Select “Don’t search. I will choose the driver to install”and “Next”.
• Click “Have Disk”and browse to C:\Program Files\Point Grey
Research\PGR FlyCapture\driver\signed\<your platform>, click
“Open”, then “OK”.
• Select the camera model (e.g. PGR Dragonfly2 DR2-COL). Click “Next”.
• You will be prompted to continue installation - click “Continue Anyway”
then “Finish”to complete installation.
8. Confirm Successful Installation
• Check the Device Manager to conrm that installation was successful. Go to
the Start menu, select Run and enter “devmgmt.msc”.Verify the camera
is listed under “Point Grey Research Devices”.
• To test the camera’s image acquisition capabilities, run the FlyCap demo
program. From the Start menu, select All Programs > Point Grey
Research > PGR FlyCapture > FlyCap.exe.
1. Recommended System Configuration
• Windows XP Service Pack 1
• 512MB of RAM
• Intel Pentium 4 2.0GHz or compatible processor
• AGP video card with 128MB video memory
• 32-bit PCI slot for IEEE-1394 card
• MicrosoftVisual C++ 6.0 (to compile and run example code)
2. Electrostatic Precautions and Camera Care
• Users who have purchased a bare board camera should:
• To clean the imaging surface of your CCD, follow the steps outlined in
www.ptgrey.com/support/kb/index.asp?a=4&q=66.
• Extended exposure to bright sunlight, rain, dusty environments, etc.
may cause problems with the electronics and the optics of the system.
• Avoid excessive shaking, dropping or mishandling of the device.
CPU RAM VIDEO PORTS
OS
2.0GHz
or equivalent
Windows XP
SP1 512mb AGP
128mb
IEEE-1394a
• Turn computer off and place the IEEE-
1394b PCI card in an open PCI slot.
• Connect the 4-pin connector on the
card to the PC power supply.
FLYCAPTURE
Software and Drivers
• Insert the FlyCapture software
CD-ROM. If the Installation Wizard
does not automatically run, browse
to your CD-ROM directory and
run the setup.exe file.
FIREWIRE
1394a
Case Level
Email:
For all general questions about Point Grey Research please
contact us at [e-mail].
For technical support (existing customers only) contact
us at www.ptgrey.com/support/contact/.
Main Office:
Mailing Address: Tel: [phone]
Point Grey Research, Inc. Toll Free (N.America only): [phone]
Richmond B.C. Canada Fax: [phone]
12051 Riverside Way Email: [e-mail]
V6W 1K7
Knowledge Base:
Find answers to commonly asked questions in our knowledge base at
www.ptgrey.com/support/kb/.
Downloads:
Users can download the latest manuals and software from
www.ptgrey.com/support/downloads/.
CONTACTING POINT GREY RESEARCH
Board Level
• This product is not intended for use in residential environments.
• Either handle bare handed or use non-chargeable gloves, clothes
or material.Also use conductive shoes.
• Install a conductive mat on the floor or working table to prevent
the generation of static electricity.
• When handling the camera unit, avoid touching the lenses. To
clean the lenses, use a standard camera lens cleaning kit or a clean
dry cotton cloth. Do not apply excessive force.
• This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesirable operation. This Class A digital apparatus complies
with Canadian ICES-003. Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du Canada.