Fisher & Paykel DCS PBE1 User manual

PBE1 Models
POWER BURNER
INSTALLATION GUIDE
US CA

1
SAFETY AND WARNINGS
!DANGER
IF YOU SMELL GAS
• Shut off gas to the appliance.
• Extinguish any open flame.
• Open lid.
• If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department.
!WARNING
• Do not store or use gasoline or other
flammable liquids or vapors in the
vicinity of this or any other appliance.
• An LP cylinder not connected for use
must not be stored in the vicinity of
this or any other appliance.
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• This appliance is equipped with a three-prong or
four-prong grounding plug for your protection
against shock hazard and should be plugged
directly into a properly grounded power outlet.
• Never remove the grounding plug or use with
a 2 prong adapter.
• Use only extension cords with a 3 prong
grounding plug, rated for the power of the
equipment, and approved for outdoor use with a
W-A marking.
• Do not immerse cord or plugs in water or other liquid.
!WARNING!
Fire Hazard
Failure to follow this advice may result in a fire
causing death or serious injury.
• This unit is for outdoor use only. Do not operate
under unprotected combustible construction. Do
not use in buildings, garages, sheds, breezeways,
covered structures or other such enclosed areas.
• Never store a spare LP cylinder under or near this
unit.
• Do not fill the gas tank more than 80% of its total
capacity.
• Do not use aluminium foil to line drip pans,
trivets or radiant trays. This can interfere with
combustion, air flow or trap excessive heat in the
control area. The result of this can be melted dials
or damaged ignition components.

2
!WARNING!
Explosion Hazard
Failure to follow this advice may result in injury
or death
• If you smell gas, do not use the appliance.
• Do not use water on grease fires, a violent steam
explosion may result. Turn all burners off, then
smother fire or flame or use dry chemical or foam-
type extinguisher.
• Do not heat unopened food containers such as
cans – build up of pressure may cause container
to burst and result in injury.
!WARNING!
Hot Surface Hazard
Failure to follow this advice may result in fire,
burns, scalds or personal injury.
• Accessible parts may become hot during use.
• When in use, do not touch the burner, trivet,
or immediate surrounding area as these areas
become extremely hot. Clean the with caution.
• Never let clothing or other flammable materials
come in contact with or get too close to any
trivet, burner or hot surface until it has cooled.
• Never lean over an open unit. When lighting a
burner, always pay close attention to what you are
doing. Be certain you are pushing the burner dial
when you attempt to light.
• Never operate the unit without a drip tray. Let hot
grease cool before attempting to handle it. Avoid
letting grease deposits collect in the drip pan.
• Ensure all controls are turned off and the unit
is cool before using any type of aerosol cleaner
on or around the product. The chemical that
produces the spraying action could, in the
presence of heat, ignite or cause metal to corrode
• Keep any electrical supply cord and the fuel
supply hose away from any heated surfaces.
WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the
important safety instructions listed below. Read all the guidance before using the appliance.
Do not use an outdoor cooking gas appliance for purposes other than intended.
Servicing
zDo not repair or replace any part of the appliance unless specifically recommended in
the user guide. All other servicing should be undertaken be a Fisher & Paykel trained and
supported service technician or qualified person.
zOnly use the product with the type of gas specified on the rating plate.
Fire Hazard
zUse only in well ventilated areas.
zNever leave the product unattended when in use.
zAlways remove the cover before lighting. Do not replace cover during cooking or before
appliance has cooled.
zDo not use a flame to check for gas leaks.
zDo not attempt to disconnect any gas connections while your appliance is in use or the
gas supply is on.
zNever connect an unregulated gas line to the appliance.
zHave an ABC rated Fire Extinguisher accessible – never attempt to extinguish a grease fire
with water or other liquids.
Storage
zWhen not in use, ensure the gas supply is turned off at the supply cylinder.
zKeep appliance covered when not in use
zStorage of the appliance indoors is permissible only if the cylinder is disconnected and
removed from the unit.
zCylinders must be stored outdoors, out of reach of children and must not be stored in a
building, garage, or any other enclosed area.
SAFETY AND WARNINGS

3
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to
change at any time. For current details about model and specification availability in your country,
please visit our website dcsappliances.com or contact your local DCS dealer.
zDo not store a full LP tank in direct sunlight.
zAfter a period of storage or non-use, the appliance should be checked for gas leaks,
deterioration, proper assembly, and burner obstructions before use.
General Use
zThis appliance is not intended to be installed in or on recreational vehicles, trailers or
boats.
zAfter lighting burners, ensure they are operating correctly.
zWhen using the appliance, be sure that all parts of the unit are firmly in place and that
everything is stable.
zDo not move the appliance during use.
zChildren should not be left alone or unattended in an area where the product is being
used. Never allow them to sit, stand or play on or around the unit at any time.
zDo not store items of interest to children around or below the appliance.
zNever use the appliance in a windy area.
zTo put out flare-ups, adjust the controls to lower the temperature.
zDo not obstruct the flow of combustion and ventilation to the appliance.
zSpiders and insects can nest in the burners or openings and can block or restrict the
burner. This can cause a flash back to the control panel which can cause a fire.
zDo not try lighting this appliance without reading the lighting instruction in the user guide.
zDo not locate, store or operate the appliance on a slope.
zThis product must be installed by a licensed plumber or gas fitter when installed within
the Commonwealth of Massachusetts.
zNever use a dented or rusty LP tank. Keep the ventilation openings of the cylinder
enclosure free and clear from debris.
zBefore each use, inspect the gas supply piping or hose prior to turning the gas ON. If
there is evidence of cuts, wear, or abrasion, it must be replaced prior to use. The pressure
regulator and hose assembly supplied with the unit must be used. If replacements are
needed, contact customer care at www.dcsappliances.com
zClean and perform general maintenance on the appliance regularly. Watch for corrosion,
cracks, or insect activity. Check the regulator, hoses, burner ports, air shutter, and venturi/
valve section carefully. Always turn off gas at the source prior to inspecting.
zYou must inspect the unit at least once a year or immediately if the smell of gas is present
in conjunction with the burner flames appearing yellow, the appliance does not reach
temperature or heats unevenly or the unit makes popping noises.
zDo not smoke while leak testing and extinguish all open flames.
zWhen cleaning the burners centre the burner onto the orifice correctly and ensure they
are level before lighting to prevent fire hazard or explosion. Refer to the user guide for
detailed guidance.
zUse only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas
appliance.
zUnplug from the outlet when not in use and before cleaning. Allow to cool before putting
on or taking off parts.
zDo not operate the appliance with a damaged cord, plug, or after the appliance
malfunctions or has been damaged in any manner. Contact the manufacturer for repair.
zDo not let the cord hang over the edge of a table or touch hot surfaces.
zWhen connecting, first connect plug to the appliance then plug appliance into the outlet.
zDo not place the unit directly on the ground or other surface without support. This will
prevent damage to the regulator/hose assembly.
Gas requirements
zThis appliance can be used with any brand of 20lb LP gas tank provided it is compatible
with a proper retention device (not supplied).
zThis appliance is set for use with either LP or NG, decided at the point of purchase.
zThe LP gas cylinder must be:
zDesigned for use with a Type 1 system only.
zConstructed and marked in accordance with the Specifications for LP gas Cylinders of
the U.S. Department of Transportation (D.O.T.) or the Standard for Cylinders, Spheres
and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339
zProvided with a listed overfilling prevention device.
zProvided with a cylinder connection device compatible with the connection for outdoor
cooking gas appliances
zThe cylinder must be provided with a shut-off valve terminating in an LP gas supply
cylinder valve outlet specified, as applicable, for connection Type 1.
zDo not change the regulator/hose assembly from that supplied with the unit or attempt
to use a Type 1 equipped regulator/hose assembly with a standard 510 POL tank/valve
assembly.
zNever use a cylinder with a damaged valve. The cylinder that is used must have a collar to
protect the cylinder valve.
zAn installer-supplied gas shut-off valve must be installed in an easily accessible location
zAll installer supplied parts must conform to local codes, or in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA
C22.1, and the National Fuel Gas Code, ANSI Z223.1 or CSA-B149.1 Natural Gas Installation
Code or CSA-B149.2 Propane Installation Code.
zIn Massachusetts such shut-off valves should be approved by the Board of State Examiners
or Plumbers & Gas Fitters.
zAll pipe sealants must be an approved type and resistant to the actions of LP gases. Never
use pipe sealant on flare fittings.
zA dented or rusty LP tank may be hazardous and should be checked by your LP supplier.
zAlways check for leaks after every LP tank change.
zFor LP units, check for leaks with a full cylinder.
zDo not use the appliance until all connections have been checked and do not leak.
SAFETY AND WARNINGS

4
PRODUCT DIMENSIONS
a
c
f
g
D
i
h
JK
L
b
e
FRONT
PLAN
PROFILE
PRODUCT DIMENSIONS
PBE1 MODELS
INCHES MM
A Overall height (excluding burners and pan supports) 10 1/2 266
B Overall width 24 610
C Overall depth (excluding dials) 26 7/8 683
D Depth of chassis 22 1/2 572
E Width of chassis (including support brackets) 21 3/4 552
F Height below countertop 10 1/8 257
G Height of surface above countertop 9/16 14
H Depth of control panel to front of chassis 251
I Depth from control panel to rear of product 25 9/16 649
J Depth of lid 23 585
K Width of lid 23 5/8 600
L Height of lid 1 11/16 43

5
BUILT-IN CONSTRUCTION
CAVITY DIMENSIONS PBE1 MODELS
INCHES MM
A Height of cutout 10 1/8 257
B Depth of cutout 22 3/4 578
C Width of cutout 22 1/2 572
D Depth of gas supply opening 4102
E Width of gas supply opening 4 15/16 125
F Height of countertop recess 6-12 152 - 305
G Minimum distance from countertop recess to cutout 376
a
I
b
c
d
f
g
e
As the power burner is designed for larger cookware, it is recommended that the product is mounted 6-12” below the countertop. Sufficient space should also be left around the product for safe
cookware handling.
Notes:
• When determining a suitable location, take into account concerns such as exposure to wind, proximity to traffic paths,
and keeping any gas supply lines as short as possible.
• Locate the unit in a well-ventilated area.
• The counter and supporting ledges or deck must be level and flat.
• The enclosure should have ventilation holes to prevent gas build-up in the event of a leak. Refer to ANSI Z21.58
Standard for Outdoor Cooking Gas Appliances, Section 1.7 Enclosures For Self Contained LP-Gas Supply Systems.
Notes:
• To purchase access doors and drawers, visit dcsappliances.com
• 24” access doors model number: ADN1-20x24
• 24” access drawers model number: ADR2-20x24
CUTOUT DIMENSIONS PBE1 MODELS
INCHES MM
A Height of cutout 11 1/8 283
B Depth of cutout 23 3/4 603
C Width of cutout 28 7/8 734
D Depth of gas supply opening 4102
E Width of gas supply opening 4102
F Depth to gas supply opening from front of cutout 18 1/2 470
G Width to gas supply opening from side of cutout 3 1/2 89
H Height of countertop recess 6-12 152 - 305
I Minimum distance from countertop recess to cutout 18 457
RECESSED CUTOUT RECESSED INSULATED JACKET CUTOUT
If the unit is to be placed into a combustible enclosure, an insulated jacket is required.
a
F
G
b
c
ed
ventilation ventilation
H

6
BUILT-IN CONSTRUCTION
CAVITY DIMENSIONS PBE1 MODELS
INCHES MM
A Height of cutout 10 1/8 257
B Depth of cutout 22 3/4 578
C Width of cutout 22 1/2 572
D Depth of gas supply opening 4102
E Width of gas supply opening 4 15/16 125
a
b
c
d
e
ventilation
a
b
c
d
f
g
e
ventilation
As the power burner is designed for larger cookware, sufficient space should be left around the product for safe handling.
Notes:
• When determining a suitable location, take into account concerns such as exposure to wind, proximity to traffic paths,
and keeping any gas supply lines as short as possible.
• Locate the unit in a well-ventilated area.
• The counter and supporting ledges or deck must be level and flat.
• The enclosure should have ventilation holes to prevent gas build-up in the event of a leak. Refer to ANSI Z21.58
Standard for Outdoor Cooking Gas Appliances, Section 1.7 Enclosures For Self Contained LP-Gas Supply Systems.
Notes:
• To purchase access doors and drawers, visit dcsappliances.com
• 24” access doors model number: ADN1-20x24
• 24” access drawers model number: ADR2-20x24
CUTOUT DIMENSIONS PBE1 MODELS
INCHES MM
A Height of cutout 11 1/8 283
B Depth of cutout 23 3/4 603
C Width of cutout 28 7/8 734
D Depth of gas supply opening 4102
E Width of gas supply opening 4102
F Depth to gas supply opening from front of cutout 18 1/2 470
G Width to gas supply opening from side of cutout 3 1/2 89
COUNTER TOP LEVEL CUTOUT COUNTER TOP LEVEL INSULATED JACKET CUTOUT
If the unit is to be placed into a combustible enclosure, an insulated jacket is required.

7
BUILT-IN CLEARANCES
CLEARANCE DIMENSIONS
PBE1 MODELS
INCHES MM
A
Minimum distance from non-combustible surface to power burner (above
the cook surface)
376
Clearances to non-combustible construction
Material which is not capable of being ignited and burned, such as
materials consisting entirely of, or a combination of, steel, iron, brick
tile, concrete, slate, and plaster.
The power burner is designed for easy placement into built-in
masonry enclosures. For non-combustible applications the power
burner drops into the opening and hangs from its side flanges. A
deck is not required to support it from the bottom.
Do not use this appliance under unprotected overhead combustible
surfaces.
Fisher&Paykel recommends installing the manual shut-off valve
in a location readily accessible by the customer, so that gas to the
appliance can be shut off in an emergency situation. However, the
appliance must not be modified in any way to accommodate such
placement.
A spirit level should be used to ensure that the unit is level both
front-to-back and side-to-side. If it is not level, burner combustion
may be erratic or the unit may not function efficiently for grease
flow.
aa

8
BUILT-IN CLEARANCES
CLEARANCE DIMENSIONS
PBE1-30 MODELS
INCHES MM
A Minimum distance from combustible surface to power burner
(above the
cook surface)
18 457
Clearances to combustible construction
Any materials of a building structure or decorative structure made
of wood, compressed paper, plant fibres, vinyl/plastic or other
materials that are capable of transferring heat or being ignited
and burned. Such material shall be considered combustible even
though flame-proofed, fire-retardant treated or surface-painted,
or plastered.
Do not use this appliance under unprotected overhead
combustible surfaces.
Fisher&Paykel recommends installing the manual shut-off
valve in a location readily accessible by the customer, so that
gas to the appliance can be shut off in an emergency situation.
However, the appliance must not be modified in any way to
accommodate such placement.
A spirit level should be used to ensure that the unit is level
both front-to-back and side-to-side. If it is not level, burner
combustion may be erratic or the unit may not function
efficiently for grease flow. a
a
Insulated jacket
If the power burner is to be placed into a combustible enclosure,
an approved insulated jacket is necessary. Insulated jackets are
available from your dealer. Use only the DCS insulated jacket
which has specifically been designed and tested for this purpose.
Review the detail drawing shown and take into account the
provisions shown for gas line connection clearance in the right
rear corner. It is required that ventilation holes are provided in the
enclosure to eliminate the potential build-up of gas in the event
of a gas leak. The supporting ledges or deck must be level and
flat and strong enough to support the power burner and insulated
jacket. The counter should also be level.
24” insulated jacket part number: 71426

9
TRIVET ASSEMBLY
MAIN TRIVET SMALL POT SUPPORT
The main trivet assembly is made up of two halves that interlock to form the cooking surface.
To install the trivets, position the feet onto the products ledge and slot the trivets together.
A small pot support is supplied with the Power Burner for cooking with pots smaller than 8”.
To install the pot support, slot onto the centre of the main trivet assembly as shown above.

10
Electrical requirements
Use only a Ground Fault Interrupter (GFI) protected circuit with
this product.
An outdoor 120VAC 15A GFI electrical outlet should be installed
by a qualified electrician either inside the island enclosure for
built-in units, or near the location where a free-standing unit
will be used. For built-in products, the supplied 12V transformer
should be connected during installation.
Installation
The transformer must be secured below the product in a dry
location away from any excessive heat. Be sure to provide
adequate access to facilitate service if the transformer or
connections require maintenance.
All units are supplied with a 12V power transformer to operate the
products ignition and dial illumination features. The transformer is
sealed in a box with an attached power supply cord.
ELECTRICAL CONNECTION
TO OUTLET
Dial halos
When a dial is in use, an orange halo around that dial will
illuminate. This will change from orange to white if the dial is
turned to OFF but another dial remains active. If all dials are
turned OFF, all halos will dim.
Multiple DCS Series 9 products may be linked together to allow
for cross-product halo illumination. To allow for this functionality,
an approved DCS kit is required and can be purchased separately
from your local DCS dealer.
If the ignition or dial halos fail to operate, a connection may
have come loose during installation or the GFI may have tripped
requiring a reset. Refer to the troubleshooting section of your
user guide for further guidance.

11
Connection: 1/2” NPT male with 3/8” flare adapter Operating pressure: 4” W.C.
Supply pressure: 5” to 14” W.C. If in excess of 14” W.C. a step down regulator is required.
Check with your local gas utility company or local codes for instructions on installing gas
supply lines. Be sure to check on type and size of run, and how deep to bury the line. If the
gas line is too small, the unit will not function properly. .
Connecting the fittings supplied with the power burner.
Use joint compound on male threads only. Do not use joint compound on the flare end of the
1/2” NPT to 3/8” flare adapter. Ensure that the regulator arrow points in the direction of gas
flow towards the unit, away from the supply. Do not forget to place the installer-supplied gas
valve in an accessible location.
base of product
open top manifold
1/2” coupling
1/2” NPT x 2.0 nipple
1/2” NPT to 3/8”
flare adapter
to gas supply
1/2” NPT x 5.0 nipple
Regulator
Verify the type of gas supply to be used, either natural or LP, and make sure the marking
on the appliance rating plate agrees with that of the supply. The rating plate is located
behind the drip tray on one of the endcaps. Never connect an unregulated gas line to the
appliance. You must use a gas regulator even if the supply is controlled.
The appliance and its individual shut-off valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of
1/2 PSIG (3.5 kPa.). The appliance must be isolated from the gas supply piping system by
closing its individual manual shut-off valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation
of this appliance must conform with local codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA 54.
Installation in Canada must be in accordance with Natural Gas and Propane Installation
Code, CSA B149.1, and/or Propane Storage and Handling Code, B149.2 and local codes.
Note:
If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced
prior to the outdoor cooking gas appliance being put into operation.
Regulator and hose replacement
The pressure regulator and hose assembly supplied with the unit must be used. If
replacements are needed, contact customer care at www.dcsappliances.com
Total gas consumption of the power burner with all burners on HI.
PBE1: 70,000 Btu/hr
GAS REQUIREMENTS NATURAL GAS CONNECTION
GAS CONNECTION

12
GAS CONNECTION
Connection: LP Hose with a Type 1 quick disconnect and regulator. Operating pressure: 11.0” W.C.
To operate your power burner on LP gas utilizing a 20lb type 1 cylinder, then a built-in LP
tank restraint must be installed prior to initial use of the power burner. The Installer must
supply ½” ID Flex hose and fixed pipe and a flare adaptor
BUILT-IN LP CONNECTION LEAK TESTING
When an LP unit is being directly connected to an LP house system, you must follow the
natural gas connection guidelines. The installer must provide the proper gas regulator to
reduce the gas pressure to 11” W.C.
1/2” ID flex hose with
1/2” NPT fittings*
Enclosure wall
Tank retention
device*
20lb LP tank*
1/2” NPT fixed pipe*
adapter 3/8” flare
fitting 1/2” NPT female
LP regulator/
hose assembly
*not supplied
base of product
open top manifold
Changing the LP cylinder
Ensure the main tank valve is turned off before turning the coupler counter clockwise, the
inlet will then disengage. Remove the inlet from the tank valve opening. Your local LP filling
station should be equipped with the proper equipment to fill your tank.
Do not attempt to remove, repair or replace the regulator/hose assembly. This must be
done by qualified and licensed technician only.
1
2
Prepare soap solution by combining
one part liquid detergent and one
part water. Pour into a spray bottle.
Ensure all control valves are in the
OFF position before turning the gas
supply ON.
Check all connections from the
supply line or LP cylinder by
applying the solution around the
connection, tubing and end of the
manifold. Soap bubbles will appear
where a leak is present.
A complete gas tightness check must be performed at the installation site. Periodically
check the whole system for leaks, or immediately if the smell of gas is present.
When using a LP gas cylinder ensure it is installed in a vertical position to provide the
required vapor withdrawal.
If a leak is present
Immediately turn the gas supply OFF and tighten any leaking connections. Turn gas ON,
and recheck. If you cannot stop a gas leak turn the gas supply OFF and call your local gas
utility or the dealer you purchased the appliance from. Only parts recommended by the
manufacturer should be used on the unit, substitution can void the warranty.
leak points
leak points
NG:
LP:

13 13
BURNER ADJUSTMENT
FLAME HEIGHT ADJUSTMENT LOW FLAME ADJUSTMENT
The valve for the outer burner feature an adjustable low setting. Due to fluctuations in gas
pressure, or heating value you may feel it necessary to increase or decrease gas flow in the
low position.
1
3
4
2
Remove the dial.
While holding the valve shaft with pliers,
insert a flat-tipped screwdriver into the
shaft and, while viewing the burner, adjust
to a minimum stable flame.
Push in and hold the selected dial
for 2 seconds before turning to HI.
Hold for 10 seconds to light the
selected burner.
Turn the control dial counter-
clockwise to the lowest setting.
BEZEL FRONT VIEW
Flames should be blue and stable with no yellow tips, excessive noise or lifting (Note: LP
units may have some yellow tipping). If any of these conditions exist, check the air shutter
and burner ports are clear. If cleaning these does not improve performance, the air shutter
for the outer burner can be adjusted as below.
yellow tips noisy/lifting blue + stable
1
3
4
2
With a screw driver, loosen the lock screw
on the face of the air shutter. If the flame
is yellow turn the air shutter counter-
clockwise, if the flame is noisy and tends
to lift turn the air shutter clockwise.
Light to check adjustment. If the flame
is blue and stable, tighten the air shutter
screw and replace all parts. If flame is still
unstable, repeat the above steps.
Ensure the power burner is
OFF and cool.
To access the air shutter, remove the
trivets and burner hob. The hob can
be removed by unscrewing the four
screws from each corner.
The burner should not be removed.
BURNER TOP VIEW

14
specified clearances are maintained to combustibles
proper enclosure ventilation has been verified
all internal packaging and any adhesive residue is removed
the burner is level and does not rock
dials turn freely, bezels centered
halo lighting is functioning correctly
all warning labels removed and supplied to customer for future reference
flame has been checked and adjusted if required
each burner lights satisfactorily - individually or with adjacent burner lit
the pressure regulator is connected and set for 4” W.C. Natural, 11.0” W.C. LP gas
the manual shut-off valve is installed and accessible
the unit has been tested and is free of leaks
the user is informed of gas supply shut-off valve location
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
INSTALLER CHECKLIST
IMPORTANT!
Read all installation instructions in this manual to see if the unit has been correctly installed.
Ensure that installation has been completed correctly before use.
Ensure that:

US CA
592070A 11.19
DCSAPPLIANCES.COM
© Fisher & Paykel Appliances 2019. All rights reserved.
The product specifications in this document apply to the specific
products and models described at the date of issue. Under our policy
of continuous product improvement, these specifications may change
at any time. You should therefore check with your Dealer to ensure this
document correctly describes the product currently available.